summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
authorDavid S. Miller <davem@davemloft.net>2013-02-18 12:35:42 -0500
committerDavid S. Miller <davem@davemloft.net>2013-02-18 12:35:42 -0500
commit2f219d5fb1184bda8398e5ab9fb2910a202e2c94 (patch)
treef5773b7c41cae27aa2ce0ec3acdbb097121dcd47
parent96b45cbd956ce83908378d87d009b05645353f22 (diff)
parent990a3158002ff19b2d665334bc7a21a8887a123d (diff)
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says: ==================== This series contains updates to e1000, e1000e, igb, igbvf and ixgbe. The e1000, e1000e, igb and igbvf are single patch changes and the remaining 11 patches are all against ixgbe. The e1000 patch is a comment cleanup to align e1000 with the code commenting style for /drivers/net. It also contains a few other white space cleanups (i.e. fix lines over 80 char, remove unnecessary blank lines and fix the use of tabs/spaces). The e1000e patch from Koki (Fujitsu) adds a warning when link speed is downgraded due to SmartSpeed. The igb patch from Stefan (Red Hat) increases the timeout in the ethtool offline self-test because some i350 adapters would sometimes fail the self-test because link auto negotiation may take longer than the current 4 second timeout. The igbvf patch from Alex is meant to address several race issues that become possible because next_to_watch could possibly be set to a value that shows that the descriptor is done when it is not. In order to correct that we instead make next_to_watch a pointer that is set to NULL during cleanup, and set to the eop_desc after the descriptor rings have been written. The remaining patches for ixgbe are a mix of fixes and added support as well as some cleanup. Most notably is the added support for displaying the number of Tx/Rx channels via ethtool by Alex. Also Aurélien adds the ability for reading data from SFP+ modules over i2c for diagnostic monitoring. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
Diffstat
-rw-r--r--drivers/net/ethernet/intel/e1000/e1000.h65
-rw-r--r--drivers/net/ethernet/intel/e1000/e1000_ethtool.c140
-rw-r--r--drivers/net/ethernet/intel/e1000/e1000_hw.c558
-rw-r--r--drivers/net/ethernet/intel/e1000/e1000_main.c322
-rw-r--r--drivers/net/ethernet/intel/e1000/e1000_param.c29
-rw-r--r--drivers/net/ethernet/intel/e1000e/netdev.c7
-rw-r--r--drivers/net/ethernet/intel/igb/igb_ethtool.c2
-rw-r--r--drivers/net/ethernet/intel/igbvf/igbvf.h2
-rw-r--r--drivers/net/ethernet/intel/igbvf/netdev.c52
-rw-r--r--drivers/net/ethernet/intel/ixgbe/ixgbe.h17
-rw-r--r--drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c257
-rw-r--r--drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c21
-rw-r--r--drivers/net/ethernet/intel/ixgbe/ixgbe_main.c125
-rw-r--r--drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c36
14 files changed, 973 insertions, 660 deletions
diff --git a/drivers/net/ethernet/intel/e1000/e1000.h b/drivers/net/ethernet/intel/e1000/e1000.h
index 2b6cd02bfba0..26d9cd59ec75 100644
--- a/drivers/net/ethernet/intel/e1000/e1000.h
+++ b/drivers/net/ethernet/intel/e1000/e1000.h
@@ -81,68 +81,69 @@ struct e1000_adapter;
#include "e1000_hw.h"
-#define E1000_MAX_INTR 10
+#define E1000_MAX_INTR 10
/* TX/RX descriptor defines */
-#define E1000_DEFAULT_TXD 256
-#define E1000_MAX_TXD 256
-#define E1000_MIN_TXD 48
-#define E1000_MAX_82544_TXD 4096
+#define E1000_DEFAULT_TXD 256
+#define E1000_MAX_TXD 256
+#define E1000_MIN_TXD 48
+#define E1000_MAX_82544_TXD 4096
-#define E1000_DEFAULT_RXD 256
-#define E1000_MAX_RXD 256
-#define E1000_MIN_RXD 48
-#define E1000_MAX_82544_RXD 4096
+#define E1000_DEFAULT_RXD 256
+#define E1000_MAX_RXD 256
+#define E1000_MIN_RXD 48
+#define E1000_MAX_82544_RXD 4096
#define E1000_MIN_ITR_USECS 10 /* 100000 irq/sec */
#define E1000_MAX_ITR_USECS 10000 /* 100 irq/sec */
/* this is the size past which hardware will drop packets when setting LPE=0 */
-#define MAXIMUM_ETHERNET_VLAN_SIZE 1522
+#define MAXIMUM_ETHERNET_VLAN_SIZE 1522
/* Supported Rx Buffer Sizes */
-#define E1000_RXBUFFER_128 128 /* Used for packet split */
-#define E1000_RXBUFFER_256 256 /* Used for packet split */
-#define E1000_RXBUFFER_512 512
-#define E1000_RXBUFFER_1024 1024
-#define E1000_RXBUFFER_2048 2048
-#define E1000_RXBUFFER_4096 4096
-#define E1000_RXBUFFER_8192 8192
-#define E1000_RXBUFFER_16384 16384
+#define E1000_RXBUFFER_128 128 /* Used for packet split */
+#define E1000_RXBUFFER_256 256 /* Used for packet split */
+#define E1000_RXBUFFER_512 512
+#define E1000_RXBUFFER_1024 1024
+#define E1000_RXBUFFER_2048 2048
+#define E1000_RXBUFFER_4096 4096
+#define E1000_RXBUFFER_8192 8192
+#define E1000_RXBUFFER_16384 16384
/* SmartSpeed delimiters */
-#define E1000_SMARTSPEED_DOWNSHIFT 3
-#define E1000_SMARTSPEED_MAX 15
+#define E1000_SMARTSPEED_DOWNSHIFT 3
+#define E1000_SMARTSPEED_MAX 15
/* Packet Buffer allocations */
-#define E1000_PBA_BYTES_SHIFT 0xA
-#define E1000_TX_HEAD_ADDR_SHIFT 7
-#define E1000_PBA_TX_MASK 0xFFFF0000
+#define E1000_PBA_BYTES_SHIFT 0xA
+#define E1000_TX_HEAD_ADDR_SHIFT 7
+#define E1000_PBA_TX_MASK 0xFFFF0000
/* Flow Control Watermarks */
-#define E1000_FC_HIGH_DIFF 0x1638 /* High: 5688 bytes below Rx FIFO size */
-#define E1000_FC_LOW_DIFF 0x1640 /* Low: 5696 bytes below Rx FIFO size */
+#define E1000_FC_HIGH_DIFF 0x1638 /* High: 5688 bytes below Rx FIFO size */
+#define E1000_FC_LOW_DIFF 0x1640 /* Low: 5696 bytes below Rx FIFO size */
-#define E1000_FC_PAUSE_TIME 0xFFFF /* pause for the max or until send xon */
+#define E1000_FC_PAUSE_TIME 0xFFFF /* pause for the max or until send xon */
/* How many Tx Descriptors do we need to call netif_wake_queue ? */
#define E1000_TX_QUEUE_WAKE 16
/* How many Rx Buffers do we bundle into one write to the hardware ? */
-#define E1000_RX_BUFFER_WRITE 16 /* Must be power of 2 */
+#define E1000_RX_BUFFER_WRITE 16 /* Must be power of 2 */
-#define AUTO_ALL_MODES 0
-#define E1000_EEPROM_82544_APM 0x0004
-#define E1000_EEPROM_APME 0x0400
+#define AUTO_ALL_MODES 0
+#define E1000_EEPROM_82544_APM 0x0004
+#define E1000_EEPROM_APME 0x0400
#ifndef E1000_MASTER_SLAVE
/* Switch to override PHY master/slave setting */
#define E1000_MASTER_SLAVE e1000_ms_hw_default
#endif
-#define E1000_MNG_VLAN_NONE (-1)
+#define E1000_MNG_VLAN_NONE (-1)
/* wrapper around a pointer to a socket buffer,
- * so a DMA handle can be stored along with the buffer */
+ * so a DMA handle can be stored along with the buffer
+ */
struct e1000_buffer {
struct sk_buff *skb;
dma_addr_t dma;
diff --git a/drivers/net/ethernet/intel/e1000/e1000_ethtool.c b/drivers/net/ethernet/intel/e1000/e1000_ethtool.c
index 14e30515f6aa..43462d596a4e 100644
--- a/drivers/net/ethernet/intel/e1000/e1000_ethtool.c
+++ b/drivers/net/ethernet/intel/e1000/e1000_ethtool.c
@@ -115,12 +115,12 @@ static int e1000_get_settings(struct net_device *netdev,
if (hw->media_type == e1000_media_type_copper) {
ecmd->supported = (SUPPORTED_10baseT_Half |
- SUPPORTED_10baseT_Full |
- SUPPORTED_100baseT_Half |
- SUPPORTED_100baseT_Full |
- SUPPORTED_1000baseT_Full|
- SUPPORTED_Autoneg |
- SUPPORTED_TP);
+ SUPPORTED_10baseT_Full |
+ SUPPORTED_100baseT_Half |
+ SUPPORTED_100baseT_Full |
+ SUPPORTED_1000baseT_Full|
+ SUPPORTED_Autoneg |
+ SUPPORTED_TP);
ecmd->advertising = ADVERTISED_TP;
if (hw->autoneg == 1) {
@@ -161,8 +161,8 @@ static int e1000_get_settings(struct net_device *netdev,
ethtool_cmd_speed_set(ecmd, adapter->link_speed);
/* unfortunately FULL_DUPLEX != DUPLEX_FULL
- * and HALF_DUPLEX != DUPLEX_HALF */
-
+ * and HALF_DUPLEX != DUPLEX_HALF
+ */
if (adapter->link_duplex == FULL_DUPLEX)
ecmd->duplex = DUPLEX_FULL;
else
@@ -179,8 +179,7 @@ static int e1000_get_settings(struct net_device *netdev,
if ((hw->media_type == e1000_media_type_copper) &&
netif_carrier_ok(netdev))
ecmd->eth_tp_mdix = (!!adapter->phy_info.mdix_mode ?
- ETH_TP_MDI_X :
- ETH_TP_MDI);
+ ETH_TP_MDI_X : ETH_TP_MDI);
else
ecmd->eth_tp_mdix = ETH_TP_MDI_INVALID;
@@ -197,8 +196,7 @@ static int e1000_set_settings(struct net_device *netdev,
struct e1000_adapter *adapter = netdev_priv(netdev);
struct e1000_hw *hw = &adapter->hw;
- /*
- * MDI setting is only allowed when autoneg enabled because
+ /* MDI setting is only allowed when autoneg enabled because
* some hardware doesn't allow MDI setting when speed or
* duplex is forced.
*/
@@ -224,8 +222,8 @@ static int e1000_set_settings(struct net_device *netdev,
ADVERTISED_Autoneg;
else
hw->autoneg_advertised = ecmd->advertising |
- ADVERTISED_TP |
- ADVERTISED_Autoneg;
+ ADVERTISED_TP |
+ ADVERTISED_Autoneg;
ecmd->advertising = hw->autoneg_advertised;
} else {
u32 speed = ethtool_cmd_speed(ecmd);
@@ -260,8 +258,7 @@ static u32 e1000_get_link(struct net_device *netdev)
{
struct e1000_adapter *adapter = netdev_priv(netdev);
- /*
- * If the link is not reported up to netdev, interrupts are disabled,
+ /* If the link is not reported up to netdev, interrupts are disabled,
* and so the physical link state may have changed since we last
* looked. Set get_link_status to make sure that the true link
* state is interrogated, rather than pulling a cached and possibly
@@ -484,7 +481,7 @@ static int e1000_get_eeprom(struct net_device *netdev,
le16_to_cpus(&eeprom_buff[i]);
memcpy(bytes, (u8 *)eeprom_buff + (eeprom->offset & 1),
- eeprom->len);
+ eeprom->len);
kfree(eeprom_buff);
return ret_val;
@@ -517,15 +514,17 @@ static int e1000_set_eeprom(struct net_device *netdev,
ptr = (void *)eeprom_buff;
if (eeprom->offset & 1) {
- /* need read/modify/write of first changed EEPROM word */
- /* only the second byte of the word is being modified */
+ /* need read/modify/write of first changed EEPROM word
+ * only the second byte of the word is being modified
+ */
ret_val = e1000_read_eeprom(hw, first_word, 1,
&eeprom_buff[0]);
ptr++;
}
if (((eeprom->offset + eeprom->len) & 1) && (ret_val == 0)) {
- /* need read/modify/write of last changed EEPROM word */
- /* only the first byte of the word is being modified */
+ /* need read/modify/write of last changed EEPROM word
+ * only the first byte of the word is being modified
+ */
ret_val = e1000_read_eeprom(hw, last_word, 1,
&eeprom_buff[last_word - first_word]);
}
@@ -606,11 +605,13 @@ static int e1000_set_ringparam(struct net_device *netdev,
rx_old = adapter->rx_ring;
err = -ENOMEM;
- txdr = kcalloc(adapter->num_tx_queues, sizeof(struct e1000_tx_ring), GFP_KERNEL);
+ txdr = kcalloc(adapter->num_tx_queues, sizeof(struct e1000_tx_ring),
+ GFP_KERNEL);
if (!txdr)
goto err_alloc_tx;
- rxdr = kcalloc(adapter->num_rx_queues, sizeof(struct e1000_rx_ring), GFP_KERNEL);
+ rxdr = kcalloc(adapter->num_rx_queues, sizeof(struct e1000_rx_ring),
+ GFP_KERNEL);
if (!rxdr)
goto err_alloc_rx;
@@ -619,12 +620,12 @@ static int e1000_set_ringparam(struct net_device *netdev,
rxdr->count = max(ring->rx_pending,(u32)E1000_MIN_RXD);
rxdr->count = min(rxdr->count,(u32)(mac_type < e1000_82544 ?
- E1000_MAX_RXD : E1000_MAX_82544_RXD));
+ E1000_MAX_RXD : E1000_MAX_82544_RXD));
rxdr->count = ALIGN(rxdr->count, REQ_RX_DESCRIPTOR_MULTIPLE);
txdr->count = max(ring->tx_pending,(u32)E1000_MIN_TXD);
txdr->count = min(txdr->count,(u32)(mac_type < e1000_82544 ?
- E1000_MAX_TXD : E1000_MAX_82544_TXD));
+ E1000_MAX_TXD : E1000_MAX_82544_TXD));
txdr->count = ALIGN(txdr->count, REQ_TX_DESCRIPTOR_MULTIPLE);
for (i = 0; i < adapter->num_tx_queues; i++)
@@ -642,7 +643,8 @@ static int e1000_set_ringparam(struct net_device *netdev,
goto err_setup_tx;
/* save the new, restore the old in order to free it,
- * then restore the new back again */
+ * then restore the new back again
+ */
adapter->rx_ring = rx_old;
adapter->tx_ring = tx_old;
@@ -784,7 +786,6 @@ static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data)
REG_SET_AND_CHECK(TCTL, 0xFFFFFFFF, 0x00000000);
if (hw->mac_type >= e1000_82543) {
-
REG_SET_AND_CHECK(RCTL, before, 0xFFFFFFFF);
REG_PATTERN_TEST(RDBAL, 0xFFFFFFF0, 0xFFFFFFFF);
REG_PATTERN_TEST(TXCW, 0xC000FFFF, 0x0000FFFF);
@@ -795,14 +796,11 @@ static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data)
REG_PATTERN_TEST(RA + (((i << 1) + 1) << 2), 0x8003FFFF,
0xFFFFFFFF);
}
-
} else {
-
REG_SET_AND_CHECK(RCTL, 0xFFFFFFFF, 0x01FFFFFF);
REG_PATTERN_TEST(RDBAL, 0xFFFFF000, 0xFFFFFFFF);
REG_PATTERN_TEST(TXCW, 0x0000FFFF, 0x0000FFFF);
REG_PATTERN_TEST(TDBAL, 0xFFFFF000, 0xFFFFFFFF);
-
}
value = E1000_MC_TBL_SIZE;
@@ -858,13 +856,14 @@ static int e1000_intr_test(struct e1000_adapter *adapter, u64 *data)
*data = 0;
- /* NOTE: we don't test MSI interrupts here, yet */
- /* Hook up test interrupt handler just for this test */
+ /* NOTE: we don't test MSI interrupts here, yet
+ * Hook up test interrupt handler just for this test
+ */
if (!request_irq(irq, e1000_test_intr, IRQF_PROBE_SHARED, netdev->name,
- netdev))
+ netdev))
shared_int = false;
else if (request_irq(irq, e1000_test_intr, IRQF_SHARED,
- netdev->name, netdev)) {
+ netdev->name, netdev)) {
*data = 1;
return -1;
}
@@ -1253,14 +1252,15 @@ static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter)
ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */
E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */
E1000_CTRL_SPD_1000 |/* Force Speed to 1000 */
- E1000_CTRL_FD); /* Force Duplex to FULL */
+ E1000_CTRL_FD); /* Force Duplex to FULL */
if (hw->media_type == e1000_media_type_copper &&
hw->phy_type == e1000_phy_m88)
ctrl_reg |= E1000_CTRL_ILOS; /* Invert Loss of Signal */
else {
/* Set the ILOS bit on the fiber Nic is half
- * duplex link is detected. */
+ * duplex link is detected.
+ */
stat_reg = er32(STATUS);
if ((stat_reg & E1000_STATUS_FD) == 0)
ctrl_reg |= (E1000_CTRL_ILOS | E1000_CTRL_SLU);
@@ -1446,7 +1446,7 @@ static int e1000_run_loopback_test(struct e1000_adapter *adapter)
ret_val = e1000_check_lbtest_frame(
rxdr->buffer_info[l].skb,
- 1024);
+ 1024);
if (!ret_val)
good_cnt++;
if (unlikely(++l == rxdr->count)) l = 0;
@@ -1493,7 +1493,8 @@ static int e1000_link_test(struct e1000_adapter *adapter, u64 *data)
hw->serdes_has_link = false;
/* On some blade server designs, link establishment
- * could take as long as 2-3 minutes */
+ * could take as long as 2-3 minutes
+ */
do {
e1000_check_for_link(hw);
if (hw->serdes_has_link)
@@ -1545,7 +1546,8 @@ static void e1000_diag_test(struct net_device *netdev,
e_info(hw, "offline testing starting\n");
/* Link test performed before hardware reset so autoneg doesn't
- * interfere with test result */
+ * interfere with test result
+ */
if (e1000_link_test(adapter, &data[4]))
eth_test->flags |= ETH_TEST_FL_FAILED;
@@ -1639,7 +1641,8 @@ static int e1000_wol_exclusion(struct e1000_adapter *adapter,
default:
/* dual port cards only support WoL on port A from now on
* unless it was enabled in the eeprom for port B
- * so exclude FUNC_1 ports from having WoL enabled */
+ * so exclude FUNC_1 ports from having WoL enabled
+ */
if (er32(STATUS) & E1000_STATUS_FUNC_1 &&
!adapter->eeprom_wol) {
wol->supported = 0;
@@ -1663,7 +1666,8 @@ static void e1000_get_wol(struct net_device *netdev,
wol->wolopts = 0;
/* this function will set ->supported = 0 and return 1 if wol is not
- * supported by this hardware */
+ * supported by this hardware
+ */
if (e1000_wol_exclusion(adapter, wol) ||
!device_can_wakeup(&adapter->pdev->dev))
return;
@@ -1839,7 +1843,7 @@ static void e1000_get_ethtool_stats(struct net_device *netdev,
data[i] = (e1000_gstrings_stats[i].sizeof_stat ==
sizeof(u64)) ? *(u64 *)p : *(u32 *)p;
}
-/* BUG_ON(i != E1000_STATS_LEN); */
+/* BUG_ON(i != E1000_STATS_LEN); */
}
static void e1000_get_strings(struct net_device *netdev, u32 stringset,
@@ -1859,37 +1863,37 @@ static void e1000_get_strings(struct net_device *netdev, u32 stringset,
ETH_GSTRING_LEN);
p += ETH_GSTRING_LEN;
}
-/* BUG_ON(p - data != E1000_STATS_LEN * ETH_GSTRING_LEN); */
+ /* BUG_ON(p - data != E1000_STATS_LEN * ETH_GSTRING_LEN); */
break;
}
}
static const struct ethtool_ops e1000_ethtool_ops = {
- .get_settings = e1000_get_settings,
- .set_settings = e1000_set_settings,
- .get_drvinfo = e1000_get_drvinfo,
- .get_regs_len = e1000_get_regs_len,
- .get_regs = e1000_get_regs,
- .get_wol = e1000_get_wol,
- .set_wol = e1000_set_wol,
- .get_msglevel = e1000_get_msglevel,
- .set_msglevel = e1000_set_msglevel,
- .nway_reset = e1000_nway_reset,
- .get_link = e1000_get_link,
- .get_eeprom_len = e1000_get_eeprom_len,
- .get_eeprom = e1000_get_eeprom,
- .set_eeprom = e1000_set_eeprom,
- .get_ringparam = e1000_get_ringparam,
- .set_ringparam = e1000_set_ringparam,
- .get_pauseparam = e1000_get_pauseparam,
- .set_pauseparam = e1000_set_pauseparam,
- .self_test = e1000_diag_test,
- .get_strings = e1000_get_strings,
- .set_phys_id = e1000_set_phys_id,
- .get_ethtool_stats = e1000_get_ethtool_stats,
- .get_sset_count = e1000_get_sset_count,
- .get_coalesce = e1000_get_coalesce,
- .set_coalesce = e1000_set_coalesce,
+ .get_settings = e1000_get_settings,
+ .set_settings = e1000_set_settings,
+ .get_drvinfo = e1000_get_drvinfo,
+ .get_regs_len = e1000_get_regs_len,
+ .get_regs = e1000_get_regs,
+ .get_wol = e1000_get_wol,
+ .set_wol = e1000_set_wol,
+ .get_msglevel = e1000_get_msglevel,
+ .set_msglevel = e1000_set_msglevel,
+ .nway_reset = e1000_nway_reset,
+ .get_link = e1000_get_link,
+ .get_eeprom_len = e1000_get_eeprom_len,
+ .get_eeprom = e1000_get_eeprom,
+ .set_eeprom = e1000_set_eeprom,
+ .get_ringparam = e1000_get_ringparam,
+ .set_ringparam = e1000_set_ringparam,
+ .get_pauseparam = e1000_get_pauseparam,
+ .set_pauseparam = e1000_set_pauseparam,
+ .self_test = e1000_diag_test,
+ .get_strings = e1000_get_strings,
+ .set_phys_id = e1000_set_phys_id,
+ .get_ethtool_stats = e1000_get_ethtool_stats,
+ .get_sset_count = e1000_get_sset_count,
+ .get_coalesce = e1000_get_coalesce,
+ .set_coalesce = e1000_set_coalesce,
.get_ts_info = ethtool_op_get_ts_info,
};
diff --git a/drivers/net/ethernet/intel/e1000/e1000_hw.c b/drivers/net/ethernet/intel/e1000/e1000_hw.c
index 8fedd2451538..2879b9631e15 100644
--- a/drivers/net/ethernet/intel/e1000/e1000_hw.c
+++ b/drivers/net/ethernet/intel/e1000/e1000_hw.c
@@ -164,8 +164,9 @@ static void e1000_phy_init_script(struct e1000_hw *hw)
if (hw->phy_init_script) {
msleep(20);
- /* Save off the current value of register 0x2F5B to be restored at
- * the end of this routine. */
+ /* Save off the current value of register 0x2F5B to be restored
+ * at the end of this routine.
+ */
ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
/* Disabled the PHY transmitter */
@@ -466,7 +467,8 @@ s32 e1000_reset_hw(struct e1000_hw *hw)
case e1000_82541:
case e1000_82541_rev_2:
/* These controllers can't ack the 64-bit write when issuing the
- * reset, so use IO-mapping as a workaround to issue the reset */
+ * reset, so use IO-mapping as a workaround to issue the reset
+ */
E1000_WRITE_REG_IO(hw, CTRL, (ctrl | E1000_CTRL_RST));
break;
case e1000_82545_rev_3:
@@ -480,9 +482,9 @@ s32 e1000_reset_hw(struct e1000_hw *hw)
break;
}
- /* After MAC reset, force reload of EEPROM to restore power-on settings to
- * device. Later controllers reload the EEPROM automatically, so just wait
- * for reload to complete.
+ /* After MAC reset, force reload of EEPROM to restore power-on settings
+ * to device. Later controllers reload the EEPROM automatically, so
+ * just wait for reload to complete.
*/
switch (hw->mac_type) {
case e1000_82542_rev2_0:
@@ -591,8 +593,8 @@ s32 e1000_init_hw(struct e1000_hw *hw)
msleep(5);
}
- /* Setup the receive address. This involves initializing all of the Receive
- * Address Registers (RARs 0 - 15).
+ /* Setup the receive address. This involves initializing all of the
+ * Receive Address Registers (RARs 0 - 15).
*/
e1000_init_rx_addrs(hw);
@@ -611,7 +613,8 @@ s32 e1000_init_hw(struct e1000_hw *hw)
for (i = 0; i < mta_size; i++) {
E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
/* use write flush to prevent Memory Write Block (MWB) from
- * occurring when accessing our register space */
+ * occurring when accessing our register space
+ */
E1000_WRITE_FLUSH();
}
@@ -630,7 +633,9 @@ s32 e1000_init_hw(struct e1000_hw *hw)
case e1000_82546_rev_3:
break;
default:
- /* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */
+ /* Workaround for PCI-X problem when BIOS sets MMRBC
+ * incorrectly.
+ */
if (hw->bus_type == e1000_bus_type_pcix
&& e1000_pcix_get_mmrbc(hw) > 2048)
e1000_pcix_set_mmrbc(hw, 2048);
@@ -660,7 +665,8 @@ s32 e1000_init_hw(struct e1000_hw *hw)
hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) {
ctrl_ext = er32(CTRL_EXT);
/* Relaxed ordering must be disabled to avoid a parity
- * error crash in a PCI slot. */
+ * error crash in a PCI slot.
+ */
ctrl_ext |= E1000_CTRL_EXT_RO_DIS;
ew32(CTRL_EXT, ctrl_ext);
}
@@ -810,8 +816,9 @@ s32 e1000_setup_link(struct e1000_hw *hw)
ew32(FCRTL, 0);
ew32(FCRTH, 0);
} else {
- /* We need to set up the Receive Threshold high and low water marks
- * as well as (optionally) enabling the transmission of XON frames.
+ /* We need to set up the Receive Threshold high and low water
+ * marks as well as (optionally) enabling the transmission of
+ * XON frames.
*/
if (hw->fc_send_xon) {
ew32(FCRTL, (hw->fc_low_water | E1000_FCRTL_XONE));
@@ -868,42 +875,46 @@ static s32 e1000_setup_fiber_serdes_link(struct e1000_hw *hw)
e1000_config_collision_dist(hw);
/* Check for a software override of the flow control settings, and setup
- * the device accordingly. If auto-negotiation is enabled, then software
- * will have to set the "PAUSE" bits to the correct value in the Tranmsit
- * Config Word Register (TXCW) and re-start auto-negotiation. However, if
- * auto-negotiation is disabled, then software will have to manually
- * configure the two flow control enable bits in the CTRL register.
+ * the device accordingly. If auto-negotiation is enabled, then
+ * software will have to set the "PAUSE" bits to the correct value in
+ * the Tranmsit Config Word Register (TXCW) and re-start
+ * auto-negotiation. However, if auto-negotiation is disabled, then
+ * software will have to manually configure the two flow control enable
+ * bits in the CTRL register.
*
* The possible values of the "fc" parameter are:
- * 0: Flow control is completely disabled
- * 1: Rx flow control is enabled (we can receive pause frames, but
- * not send pause frames).
- * 2: Tx flow control is enabled (we can send pause frames but we do
- * not support receiving pause frames).
- * 3: Both Rx and TX flow control (symmetric) are enabled.
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames, but
+ * not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames but we do
+ * not support receiving pause frames).
+ * 3: Both Rx and TX flow control (symmetric) are enabled.
*/
switch (hw->fc) {
case E1000_FC_NONE:
- /* Flow control is completely disabled by a software over-ride. */
+ /* Flow ctrl is completely disabled by a software over-ride */
txcw = (E1000_TXCW_ANE | E1000_TXCW_FD);
break;
case E1000_FC_RX_PAUSE:
- /* RX Flow control is enabled and TX Flow control is disabled by a
- * software over-ride. Since there really isn't a way to advertise
- * that we are capable of RX Pause ONLY, we will advertise that we
- * support both symmetric and asymmetric RX PAUSE. Later, we will
- * disable the adapter's ability to send PAUSE frames.
+ /* Rx Flow control is enabled and Tx Flow control is disabled by
+ * a software over-ride. Since there really isn't a way to
+ * advertise that we are capable of Rx Pause ONLY, we will
+ * advertise that we support both symmetric and asymmetric Rx
+ * PAUSE. Later, we will disable the adapter's ability to send
+ * PAUSE frames.
*/
txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
break;
case E1000_FC_TX_PAUSE:
- /* TX Flow control is enabled, and RX Flow control is disabled, by a
- * software over-ride.
+ /* Tx Flow control is enabled, and Rx Flow control is disabled,
+ * by a software over-ride.
*/
txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR);
break;
case E1000_FC_FULL:
- /* Flow control (both RX and TX) is enabled by a software over-ride. */
+ /* Flow control (both Rx and Tx) is enabled by a software
+ * over-ride.
+ */
txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
break;
default:
@@ -912,11 +923,11 @@ static s32 e1000_setup_fiber_serdes_link(struct e1000_hw *hw)
break;
}
- /* Since auto-negotiation is enabled, take the link out of reset (the link
- * will be in reset, because we previously reset the chip). This will
- * restart auto-negotiation. If auto-negotiation is successful then the
- * link-up status bit will be set and the flow control enable bits (RFCE
- * and TFCE) will be set according to their negotiated value.
+ /* Since auto-negotiation is enabled, take the link out of reset (the
+ * link will be in reset, because we previously reset the chip). This
+ * will restart auto-negotiation. If auto-negotiation is successful
+ * then the link-up status bit will be set and the flow control enable
+ * bits (RFCE and TFCE) will be set according to their negotiated value.
*/
e_dbg("Auto-negotiation enabled\n");
@@ -927,11 +938,12 @@ static s32 e1000_setup_fiber_serdes_link(struct e1000_hw *hw)
hw->txcw = txcw;
msleep(1);
- /* If we have a signal (the cable is plugged in) then poll for a "Link-Up"
- * indication in the Device Status Register. Time-out if a link isn't
- * seen in 500 milliseconds seconds (Auto-negotiation should complete in
- * less than 500 milliseconds even if the other end is doing it in SW).
- * For internal serdes, we just assume a signal is present, then poll.
+ /* If we have a signal (the cable is plugged in) then poll for a
+ * "Link-Up" indication in the Device Status Register. Time-out if a
+ * link isn't seen in 500 milliseconds seconds (Auto-negotiation should
+ * complete in less than 500 milliseconds even if the other end is doing
+ * it in SW). For internal serdes, we just assume a signal is present,
+ * then poll.
*/
if (hw->media_type == e1000_media_type_internal_serdes ||
(er32(CTRL) & E1000_CTRL_SWDPIN1) == signal) {
@@ -946,9 +958,9 @@ static s32 e1000_setup_fiber_serdes_link(struct e1000_hw *hw)
e_dbg("Never got a valid link from auto-neg!!!\n");
hw->autoneg_failed = 1;
/* AutoNeg failed to achieve a link, so we'll call
- * e1000_check_for_link. This routine will force the link up if
- * we detect a signal. This will allow us to communicate with
- * non-autonegotiating link partners.
+ * e1000_check_for_link. This routine will force the
+ * link up if we detect a signal. This will allow us to
+ * communicate with non-autonegotiating link partners.
*/
ret_val = e1000_check_for_link(hw);
if (ret_val) {
@@ -1042,9 +1054,9 @@ static s32 e1000_copper_link_preconfig(struct e1000_hw *hw)
e_dbg("e1000_copper_link_preconfig");
ctrl = er32(CTRL);
- /* With 82543, we need to force speed and duplex on the MAC equal to what
- * the PHY speed and duplex configuration is. In addition, we need to
- * perform a hardware reset on the PHY to take it out of reset.
+ /* With 82543, we need to force speed and duplex on the MAC equal to
+ * what the PHY speed and duplex configuration is. In addition, we need
+ * to perform a hardware reset on the PHY to take it out of reset.
*/
if (hw->mac_type > e1000_82543) {
ctrl |= E1000_CTRL_SLU;
@@ -1175,7 +1187,8 @@ static s32 e1000_copper_link_igp_setup(struct e1000_hw *hw)
/* when autonegotiation advertisement is only 1000Mbps then we
* should disable SmartSpeed and enable Auto MasterSlave
- * resolution as hardware default. */
+ * resolution as hardware default.
+ */
if (hw->autoneg_advertised == ADVERTISE_1000_FULL) {
/* Disable SmartSpeed */
ret_val =
@@ -1485,13 +1498,15 @@ static s32 e1000_setup_copper_link(struct e1000_hw *hw)
if (hw->autoneg) {
/* Setup autoneg and flow control advertisement
- * and perform autonegotiation */
+ * and perform autonegotiation
+ */
ret_val = e1000_copper_link_autoneg(hw);
if (ret_val)
return ret_val;
} else {
/* PHY will be set to 10H, 10F, 100H,or 100F
- * depending on value from forced_speed_duplex. */
+ * depending on value from forced_speed_duplex.
+ */
e_dbg("Forcing speed and duplex\n");
ret_val = e1000_phy_force_speed_duplex(hw);
if (ret_val) {
@@ -1609,7 +1624,8 @@ s32 e1000_phy_setup_autoneg(struct e1000_hw *hw)
* setup the PHY advertisement registers accordingly. If
* auto-negotiation is enabled, then software will have to set the
* "PAUSE" bits to the correct value in the Auto-Negotiation
- * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation.
+ * Advertisement Register (PHY_AUTONEG_ADV) and re-start
+ * auto-negotiation.
*
* The possible values of the "fc" parameter are:
* 0: Flow control is completely disabled
@@ -1636,7 +1652,7 @@ s32 e1000_phy_setup_autoneg(struct e1000_hw *hw)
* capable of RX Pause ONLY, we will advertise that we
* support both symmetric and asymmetric RX PAUSE. Later
* (in e1000_config_fc_after_link_up) we will disable the
- *hw's ability to send PAUSE frames.
+ * hw's ability to send PAUSE frames.
*/
mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
break;
@@ -1720,15 +1736,15 @@ static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw)
/* Are we forcing Full or Half Duplex? */
if (hw->forced_speed_duplex == e1000_100_full ||
hw->forced_speed_duplex == e1000_10_full) {
- /* We want to force full duplex so we SET the full duplex bits in the
- * Device and MII Control Registers.
+ /* We want to force full duplex so we SET the full duplex bits
+ * in the Device and MII Control Registers.
*/
ctrl |= E1000_CTRL_FD;
mii_ctrl_reg |= MII_CR_FULL_DUPLEX;
e_dbg("Full Duplex\n");
} else {
- /* We want to force half duplex so we CLEAR the full duplex bits in
- * the Device and MII Control Registers.
+ /* We want to force half duplex so we CLEAR the full duplex bits
+ * in the Device and MII Control Registers.
*/
ctrl &= ~E1000_CTRL_FD;
mii_ctrl_reg &= ~MII_CR_FULL_DUPLEX;
@@ -1762,8 +1778,8 @@ static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw)
if (ret_val)
return ret_val;
- /* Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI
- * forced whenever speed are duplex are forced.
+ /* Clear Auto-Crossover to force MDI manually. M88E1000 requires
+ * MDI forced whenever speed are duplex are forced.
*/
phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;
ret_val =
@@ -1814,10 +1830,10 @@ static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw)
e_dbg("Waiting for forced speed/duplex link.\n");
mii_status_reg = 0;
- /* We will wait for autoneg to complete or 4.5 seconds to expire. */
+ /* Wait for autoneg to complete or 4.5 seconds to expire */
for (i = PHY_FORCE_TIME; i > 0; i--) {
- /* Read the MII Status Register and wait for Auto-Neg Complete bit
- * to be set.
+ /* Read the MII Status Register and wait for Auto-Neg
+ * Complete bit to be set.
*/
ret_val =
e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
@@ -1834,20 +1850,24 @@ static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw)
msleep(100);
}
if ((i == 0) && (hw->phy_type == e1000_phy_m88)) {
- /* We didn't get link. Reset the DSP and wait again for link. */
+ /* We didn't get link. Reset the DSP and wait again
+ * for link.
+ */
ret_val = e1000_phy_reset_dsp(hw);
if (ret_val) {
e_dbg("Error Resetting PHY DSP\n");
return ret_val;
}
}
- /* This loop will early-out if the link condition has been met. */
+ /* This loop will early-out if the link condition has been
+ * met
+ */
for (i = PHY_FORCE_TIME; i > 0; i--) {
if (mii_status_reg & MII_SR_LINK_STATUS)
break;
msleep(100);
- /* Read the MII Status Register and wait for Auto-Neg Complete bit
- * to be set.
+ /* Read the MII Status Register and wait for Auto-Neg
+ * Complete bit to be set.
*/
ret_val =
e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg);
@@ -1862,9 +1882,10 @@ static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw)
}
if (hw->phy_type == e1000_phy_m88) {
- /* Because we reset the PHY above, we need to re-force TX_CLK in the
- * Extended PHY Specific Control Register to 25MHz clock. This value
- * defaults back to a 2.5MHz clock when the PHY is reset.
+ /* Because we reset the PHY above, we need to re-force TX_CLK in
+ * the Extended PHY Specific Control Register to 25MHz clock.
+ * This value defaults back to a 2.5MHz clock when the PHY is
+ * reset.
*/
ret_val =
e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL,
@@ -1879,8 +1900,9 @@ static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw)
if (ret_val)
return ret_val;
- /* In addition, because of the s/w reset above, we need to enable CRS on
- * TX. This must be set for both full and half duplex operation.
+ /* In addition, because of the s/w reset above, we need to
+ * enable CRS on Tx. This must be set for both full and half
+ * duplex operation.
*/
ret_val =
e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
@@ -1951,7 +1973,8 @@ static s32 e1000_config_mac_to_phy(struct e1000_hw *hw)
e_dbg("e1000_config_mac_to_phy");
/* 82544 or newer MAC, Auto Speed Detection takes care of
- * MAC speed/duplex configuration.*/
+ * MAC speed/duplex configuration.
+ */
if ((hw->mac_type >= e1000_82544) && (hw->mac_type != e1000_ce4100))
return E1000_SUCCESS;
@@ -1985,7 +2008,7 @@ static s32 e1000_config_mac_to_phy(struct e1000_hw *hw)
* registers depending on negotiated values.
*/
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS,
- &phy_data);
+ &phy_data);
if (ret_val)
return ret_val;
@@ -2002,7 +2025,7 @@ static s32 e1000_config_mac_to_phy(struct e1000_hw *hw)
if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS)
ctrl |= E1000_CTRL_SPD_1000;
else if ((phy_data & M88E1000_PSSR_SPEED) ==
- M88E1000_PSSR_100MBS)
+ M88E1000_PSSR_100MBS)
ctrl |= E1000_CTRL_SPD_100;
}
@@ -2135,9 +2158,9 @@ static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw)
if (mii_status_reg & MII_SR_AUTONEG_COMPLETE) {
/* The AutoNeg process has completed, so we now need to
* read both the Auto Negotiation Advertisement Register
- * (Address 4) and the Auto_Negotiation Base Page Ability
- * Register (Address 5) to determine how flow control was
- * negotiated.
+ * (Address 4) and the Auto_Negotiation Base Page
+ * Ability Register (Address 5) to determine how flow
+ * control was negotiated.
*/
ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV,
&mii_nway_adv_reg);
@@ -2148,18 +2171,19 @@ static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw)
if (ret_val)
return ret_val;
- /* Two bits in the Auto Negotiation Advertisement Register
- * (Address 4) and two bits in the Auto Negotiation Base
- * Page Ability Register (Address 5) determine flow control
- * for both the PHY and the link partner. The following
- * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
- * 1999, describes these PAUSE resolution bits and how flow
- * control is determined based upon these settings.
+ /* Two bits in the Auto Negotiation Advertisement
+ * Register (Address 4) and two bits in the Auto
+ * Negotiation Base Page Ability Register (Address 5)
+ * determine flow control for both the PHY and the link
+ * partner. The following table, taken out of the IEEE
+ * 802.3ab/D6.0 dated March 25, 1999, describes these
+ * PAUSE resolution bits and how flow control is
+ * determined based upon these settings.
* NOTE: DC = Don't Care
*
* LOCAL DEVICE | LINK PARTNER
* PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
- *-------|---------|-------|---------|--------------------
+ *-------|---------|-------|---------|------------------
* 0 | 0 | DC | DC | E1000_FC_NONE
* 0 | 1 | 0 | DC | E1000_FC_NONE
* 0 | 1 | 1 | 0 | E1000_FC_NONE
@@ -2178,17 +2202,18 @@ static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw)
*
* LOCAL DEVICE | LINK PARTNER
* PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
- *-------|---------|-------|---------|--------------------
+ *-------|---------|-------|---------|------------------
* 1 | DC | 1 | DC | E1000_FC_FULL
*
*/
if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
- /* Now we need to check if the user selected RX ONLY
- * of pause frames. In this case, we had to advertise
- * FULL flow control because we could not advertise RX
- * ONLY. Hence, we must now check to see if we need to
- * turn OFF the TRANSMISSION of PAUSE frames.
+ /* Now we need to check if the user selected Rx
+ * ONLY of pause frames. In this case, we had
+ * to advertise FULL flow control because we
+ * could not advertise Rx ONLY. Hence, we must
+ * now check to see if we need to turn OFF the
+ * TRANSMISSION of PAUSE frames.
*/
if (hw->original_fc == E1000_FC_FULL) {
hw->fc = E1000_FC_FULL;
@@ -2203,7 +2228,7 @@ static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw)
*
* LOCAL DEVICE | LINK PARTNER
* PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
- *-------|---------|-------|---------|--------------------
+ *-------|---------|-------|---------|------------------
* 0 | 1 | 1 | 1 | E1000_FC_TX_PAUSE
*
*/
@@ -2220,7 +2245,7 @@ static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw)
*
* LOCAL DEVICE | LINK PARTNER
* PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
- *-------|---------|-------|---------|--------------------
+ *-------|---------|-------|---------|------------------
* 1 | 1 | 0 | 1 | E1000_FC_RX_PAUSE
*
*/
@@ -2233,25 +2258,27 @@ static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw)
e_dbg
("Flow Control = RX PAUSE frames only.\n");
}
- /* Per the IEEE spec, at this point flow control should be
- * disabled. However, we want to consider that we could
- * be connected to a legacy switch that doesn't advertise
- * desired flow control, but can be forced on the link
- * partner. So if we advertised no flow control, that is
- * what we will resolve to. If we advertised some kind of
- * receive capability (Rx Pause Only or Full Flow Control)
- * and the link partner advertised none, we will configure
- * ourselves to enable Rx Flow Control only. We can do
- * this safely for two reasons: If the link partner really
- * didn't want flow control enabled, and we enable Rx, no
- * harm done since we won't be receiving any PAUSE frames
- * anyway. If the intent on the link partner was to have
- * flow control enabled, then by us enabling RX only, we
- * can at least receive pause frames and process them.
- * This is a good idea because in most cases, since we are
- * predominantly a server NIC, more times than not we will
- * be asked to delay transmission of packets than asking
- * our link partner to pause transmission of frames.
+ /* Per the IEEE spec, at this point flow control should
+ * be disabled. However, we want to consider that we
+ * could be connected to a legacy switch that doesn't
+ * advertise desired flow control, but can be forced on
+ * the link partner. So if we advertised no flow
+ * control, that is what we will resolve to. If we
+ * advertised some kind of receive capability (Rx Pause
+ * Only or Full Flow Control) and the link partner
+ * advertised none, we will configure ourselves to
+ * enable Rx Flow Control only. We can do this safely
+ * for two reasons: If the link partner really
+ * didn't want flow control enabled, and we enable Rx,
+ * no harm done since we won't be receiving any PAUSE
+ * frames anyway. If the intent on the link partner was
+ * to have flow control enabled, then by us enabling Rx
+ * only, we can at least receive pause frames and
+ * process them. This is a good idea because in most
+ * cases, since we are predominantly a server NIC, more
+ * times than not we will be asked to delay transmission
+ * of packets than asking our link partner to pause
+ * transmission of frames.
*/
else if ((hw->original_fc == E1000_FC_NONE ||
hw->original_fc == E1000_FC_TX_PAUSE) ||
@@ -2316,8 +2343,7 @@ static s32 e1000_check_for_serdes_link_generic(struct e1000_hw *hw)
status = er32(STATUS);
rxcw = er32(RXCW);
- /*
- * If we don't have link (auto-negotiation failed or link partner
+ /* If we don't have link (auto-negotiation failed or link partner
* cannot auto-negotiate), and our link partner is not trying to
* auto-negotiate with us (we are receiving idles or data),
* we need to force link up. We also need to give auto-negotiation
@@ -2346,8 +2372,7 @@ static s32 e1000_check_for_serdes_link_generic(struct e1000_hw *hw)
goto out;
}
} else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
- /*
- * If we are forcing link and we are receiving /C/ ordered
+ /* If we are forcing link and we are receiving /C/ ordered
* sets, re-enable auto-negotiation in the TXCW register
* and disable forced link in the Device Control register
* in an attempt to auto-negotiate with our link partner.
@@ -2358,8 +2383,7 @@ static s32 e1000_check_for_serdes_link_generic(struct e1000_hw *hw)
hw->serdes_has_link = true;
} else if (!(E1000_TXCW_ANE & er32(TXCW))) {
- /*
- * If we force link for non-auto-negotiation switch, check
+ /* If we force link for non-auto-negotiation switch, check
* link status based on MAC synchronization for internal
* serdes media type.
*/
@@ -2468,15 +2492,17 @@ s32 e1000_check_for_link(struct e1000_hw *hw)
if (phy_data & MII_SR_LINK_STATUS) {
hw->get_link_status = false;
- /* Check if there was DownShift, must be checked immediately after
- * link-up */
+ /* Check if there was DownShift, must be checked
+ * immediately after link-up
+ */
e1000_check_downshift(hw);
/* If we are on 82544 or 82543 silicon and speed/duplex
- * are forced to 10H or 10F, then we will implement the polarity
- * reversal workaround. We disable interrupts first, and upon
- * returning, place the devices interrupt state to its previous
- * value except for the link status change interrupt which will
+ * are forced to 10H or 10F, then we will implement the
+ * polarity reversal workaround. We disable interrupts
+ * first, and upon returning, place the devices
+ * interrupt state to its previous value except for the
+ * link status change interrupt which will
* happen due to the execution of this workaround.
*/
@@ -2527,9 +2553,10 @@ s32 e1000_check_for_link(struct e1000_hw *hw)
}
}
- /* Configure Flow Control now that Auto-Neg has completed. First, we
- * need to restore the desired flow control settings because we may
- * have had to re-autoneg with a different link partner.
+ /* Configure Flow Control now that Auto-Neg has completed.
+ * First, we need to restore the desired flow control settings
+ * because we may have had to re-autoneg with a different link
+ * partner.
*/
ret_val = e1000_config_fc_after_link_up(hw);
if (ret_val) {
@@ -2538,11 +2565,12 @@ s32 e1000_check_for_link(struct e1000_hw *hw)
}
/* At this point we know that we are on copper and we have
- * auto-negotiated link. These are conditions for checking the link
- * partner capability register. We use the link speed to determine if
- * TBI compatibility needs to be turned on or off. If the link is not
- * at gigabit speed, then TBI compatibility is not needed. If we are
- * at gigabit speed, we turn on TBI compatibility.
+ * auto-negotiated link. These are conditions for checking the
+ * link partner capability register. We use the link speed to
+ * determine if TBI compatibility needs to be turned on or off.
+ * If the link is not at gigabit speed, then TBI compatibility
+ * is not needed. If we are at gigabit speed, we turn on TBI
+ * compatibility.
*/
if (hw->tbi_compatibility_en) {
u16 speed, duplex;
@@ -2554,20 +2582,23 @@ s32 e1000_check_for_link(struct e1000_hw *hw)
return ret_val;
}
if (speed != SPEED_1000) {
- /* If link speed is not set to gigabit speed, we do not need
- * to enable TBI compatibility.
+ /* If link speed is not set to gigabit speed, we
+ * do not need to enable TBI compatibility.
*/
if (hw->tbi_compatibility_on) {
- /* If we previously were in the mode, turn it off. */
+ /* If we previously were in the mode,
+ * turn it off.
+ */
rctl = er32(RCTL);
rctl &= ~E1000_RCTL_SBP;
ew32(RCTL, rctl);
hw->tbi_compatibility_on = false;
}
} else {
- /* If TBI compatibility is was previously off, turn it on. For
- * compatibility with a TBI link partner, we will store bad
- * packets. Some frames have an additional byte on the end and
+ /* If TBI compatibility is was previously off,
+ * turn it on. For compatibility with a TBI link
+ * partner, we will store bad packets. Some
+ * frames have an additional byte on the end and
* will look like CRC errors to to the hardware.
*/
if (!hw->tbi_compatibility_on) {
@@ -2629,9 +2660,9 @@ s32 e1000_get_speed_and_duplex(struct e1000_hw *hw, u16 *speed, u16 *duplex)
*duplex = FULL_DUPLEX;
}
- /* IGP01 PHY may advertise full duplex operation after speed downgrade even
- * if it is operating at half duplex. Here we set the duplex settings to
- * match the duplex in the link partner's capabilities.
+ /* IGP01 PHY may advertise full duplex operation after speed downgrade
+ * even if it is operating at half duplex. Here we set the duplex
+ * settings to match the duplex in the link partner's capabilities.
*/
if (hw->phy_type == e1000_phy_igp && hw->speed_downgraded) {
ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_EXP, &phy_data);
@@ -2697,8 +2728,8 @@ static s32 e1000_wait_autoneg(struct e1000_hw *hw)
*/
static void e1000_raise_mdi_clk(struct e1000_hw *hw, u32 *ctrl)
{
- /* Raise the clock input to the Management Data Clock (by setting the MDC
- * bit), and then delay 10 microseconds.
+ /* Raise the clock input to the Management Data Clock (by setting the
+ * MDC bit), and then delay 10 microseconds.
*/
ew32(CTRL, (*ctrl | E1000_CTRL_MDC));
E1000_WRITE_FLUSH();
@@ -2712,8 +2743,8 @@ static void e1000_raise_mdi_clk(struct e1000_hw *hw, u32 *ctrl)
*/
static void e1000_lower_mdi_clk(struct e1000_hw *hw, u32 *ctrl)
{
- /* Lower the clock input to the Management Data Clock (by clearing the MDC
- * bit), and then delay 10 microseconds.
+ /* Lower the clock input to the Management Data Clock (by clearing the
+ * MDC bit), and then delay 10 microseconds.
*/
ew32(CTRL, (*ctrl & ~E1000_CTRL_MDC));
E1000_WRITE_FLUSH();
@@ -2746,10 +2777,10 @@ static void e1000_shift_out_mdi_bits(struct e1000_hw *hw, u32 data, u16 count)
ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR);
while (mask) {
- /* A "1" is shifted out to the PHY by setting the MDIO bit to "1" and
- * then raising and lowering the Management Data Clock. A "0" is
- * shifted out to the PHY by setting the MDIO bit to "0" and then
- * raising and lowering the clock.
+ /* A "1" is shifted out to the PHY by setting the MDIO bit to
+ * "1" and then raising and lowering the Management Data Clock.
+ * A "0" is shifted out to the PHY by setting the MDIO bit to
+ * "0" and then raising and lowering the clock.
*/
if (data & mask)
ctrl |= E1000_CTRL_MDIO;
@@ -2781,24 +2812,26 @@ static u16 e1000_shift_in_mdi_bits(struct e1000_hw *hw)
u8 i;
/* In order to read a register from the PHY, we need to shift in a total
- * of 18 bits from the PHY. The first two bit (turnaround) times are used
- * to avoid contention on the MDIO pin when a read operation is performed.
- * These two bits are ignored by us and thrown away. Bits are "shifted in"
- * by raising the input to the Management Data Clock (setting the MDC bit),
- * and then reading the value of the MDIO bit.
+ * of 18 bits from the PHY. The first two bit (turnaround) times are
+ * used to avoid contention on the MDIO pin when a read operation is
+ * performed. These two bits are ignored by us and thrown away. Bits are
+ * "shifted in" by raising the input to the Management Data Clock
+ * (setting the MDC bit), and then reading the value of the MDIO bit.
*/
ctrl = er32(CTRL);
- /* Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as input. */
+ /* Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as
+ * input.
+ */
ctrl &= ~E1000_CTRL_MDIO_DIR;
ctrl &= ~E1000_CTRL_MDIO;
ew32(CTRL, ctrl);
E1000_WRITE_FLUSH();
- /* Raise and Lower the clock before reading in the data. This accounts for
- * the turnaround bits. The first clock occurred when we clocked out the
- * last bit of the Register Address.
+ /* Raise and Lower the clock before reading in the data. This accounts
+ * for the turnaround bits. The first clock occurred when we clocked out
+ * the last bit of the Register Address.
*/
e1000_raise_mdi_clk(hw, &ctrl);
e1000_lower_mdi_clk(hw, &ctrl);
@@ -2870,8 +2903,8 @@ static s32 e1000_read_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr,
if (hw->mac_type > e1000_82543) {
/* Set up Op-code, Phy Address, and register address in the MDI
- * Control register. The MAC will take care of interfacing with the
- * PHY to retrieve the desired data.
+ * Control register. The MAC will take care of interfacing with
+ * the PHY to retrieve the desired data.
*/
if (hw->mac_type == e1000_ce4100) {
mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) |
@@ -2929,31 +2962,32 @@ static s32 e1000_read_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr,
*phy_data = (u16) mdic;
}
} else {
- /* We must first send a preamble through the MDIO pin to signal the
- * beginning of an MII instruction. This is done by sending 32
- * consecutive "1" bits.
+ /* We must first send a preamble through the MDIO pin to signal
+ * the beginning of an MII instruction. This is done by sending
+ * 32 consecutive "1" bits.
*/
e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE);
/* Now combine the next few fields that are required for a read
* operation. We use this method instead of calling the
- * e1000_shift_out_mdi_bits routine five different times. The format of
- * a MII read instruction consists of a shift out of 14 bits and is
- * defined as follows:
+ * e1000_shift_out_mdi_bits routine five different times. The
+ * format of a MII read instruction consists of a shift out of
+ * 14 bits and is defined as follows:
* <Preamble><SOF><Op Code><Phy Addr><Reg Addr>
- * followed by a shift in of 18 bits. This first two bits shifted in
- * are TurnAround bits used to avoid contention on the MDIO pin when a
- * READ operation is performed. These two bits are thrown away
- * followed by a shift in of 16 bits which contains the desired data.
+ * followed by a shift in of 18 bits. This first two bits
+ * shifted in are TurnAround bits used to avoid contention on
+ * the MDIO pin when a READ operation is performed. These two
+ * bits are thrown away followed by a shift in of 16 bits which
+ * contains the desired data.
*/
mdic = ((reg_addr) | (phy_addr << 5) |
(PHY_OP_READ << 10) | (PHY_SOF << 12));
e1000_shift_out_mdi_bits(hw, mdic, 14);
- /* Now that we've shifted out the read command to the MII, we need to
- * "shift in" the 16-bit value (18 total bits) of the requested PHY
- * register address.
+ /* Now that we've shifted out the read command to the MII, we
+ * need to "shift in" the 16-bit value (18 total bits) of the
+ * requested PHY register address.
*/
*phy_data = e1000_shift_in_mdi_bits(hw);
}
@@ -3060,18 +3094,18 @@ static s32 e1000_write_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr,
}
}
} else {
- /* We'll need to use the SW defined pins to shift the write command
- * out to the PHY. We first send a preamble to the PHY to signal the
- * beginning of the MII instruction. This is done by sending 32
- * consecutive "1" bits.
+ /* We'll need to use the SW defined pins to shift the write
+ * command out to the PHY. We first send a preamble to the PHY
+ * to signal the beginning of the MII instruction. This is done
+ * by sending 32 consecutive "1" bits.
*/
e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE);
- /* Now combine the remaining required fields that will indicate a
- * write operation. We use this method instead of calling the
- * e1000_shift_out_mdi_bits routine for each field in the command. The
- * format of a MII write instruction is as follows:
- * <Preamble><SOF><Op Code><Phy Addr><Reg Addr><Turnaround><Data>.
+ /* Now combine the remaining required fields that will indicate
+ * a write operation. We use this method instead of calling the
+ * e1000_shift_out_mdi_bits routine for each field in the
+ * command. The format of a MII write instruction is as follows:
+ * <Preamble><SOF><OpCode><PhyAddr><RegAddr><Turnaround><Data>.
*/
mdic = ((PHY_TURNAROUND) | (reg_addr << 2) | (phy_addr << 7) |
(PHY_OP_WRITE << 12) | (PHY_SOF << 14));
@@ -3100,10 +3134,10 @@ s32 e1000_phy_hw_reset(struct e1000_hw *hw)
e_dbg("Resetting Phy...\n");
if (hw->mac_type > e1000_82543) {
- /* Read the device control register and assert the E1000_CTRL_PHY_RST
- * bit. Then, take it out of reset.
+ /* Read the device control register and assert the
+ * E1000_CTRL_PHY_RST bit. Then, take it out of reset.
* For e1000 hardware, we delay for 10ms between the assert
- * and deassert.
+ * and de-assert.
*/
ctrl = er32(CTRL);
ew32(CTRL, ctrl | E1000_CTRL_PHY_RST);
@@ -3115,8 +3149,9 @@ s32 e1000_phy_hw_reset(struct e1000_hw *hw)
E1000_WRITE_FLUSH();
} else {
- /* Read the Extended Device Control Register, assert the PHY_RESET_DIR
- * bit to put the PHY into reset. Then, take it out of reset.
+ /* Read the Extended Device Control Register, assert the
+ * PHY_RESET_DIR bit to put the PHY into reset. Then, take it
+ * out of reset.
*/
ctrl_ext = er32(CTRL_EXT);
ctrl_ext |= E1000_CTRL_EXT_SDP4_DIR;
@@ -3301,7 +3336,8 @@ static s32 e1000_phy_igp_get_info(struct e1000_hw *hw,
e_dbg("e1000_phy_igp_get_info");
/* The downshift status is checked only once, after link is established,
- * and it stored in the hw->speed_downgraded parameter. */
+ * and it stored in the hw->speed_downgraded parameter.
+ */
phy_info->downshift = (e1000_downshift) hw->speed_downgraded;
/* IGP01E1000 does not need to support it. */
@@ -3327,7 +3363,9 @@ static s32 e1000_phy_igp_get_info(struct e1000_hw *hw,
if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
IGP01E1000_PSSR_SPEED_1000MBPS) {
- /* Local/Remote Receiver Information are only valid at 1000 Mbps */
+ /* Local/Remote Receiver Information are only valid @ 1000
+ * Mbps
+ */
ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data);
if (ret_val)
return ret_val;
@@ -3379,7 +3417,8 @@ static s32 e1000_phy_m88_get_info(struct e1000_hw *hw,
e_dbg("e1000_phy_m88_get_info");
/* The downshift status is checked only once, after link is established,
- * and it stored in the hw->speed_downgraded parameter. */
+ * and it stored in the hw->speed_downgraded parameter.
+ */
phy_info->downshift = (e1000_downshift) hw->speed_downgraded;
ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
@@ -3574,8 +3613,8 @@ s32 e1000_init_eeprom_params(struct e1000_hw *hw)
}
if (eeprom->type == e1000_eeprom_spi) {
- /* eeprom_size will be an enum [0..8] that maps to eeprom sizes 128B to
- * 32KB (incremented by powers of 2).
+ /* eeprom_size will be an enum [0..8] that maps to eeprom sizes
+ * 128B to 32KB (incremented by powers of 2).
*/
/* Set to default value for initial eeprom read. */
eeprom->word_size = 64;
@@ -3585,8 +3624,9 @@ s32 e1000_init_eeprom_params(struct e1000_hw *hw)
eeprom_size =
(eeprom_size & EEPROM_SIZE_MASK) >> EEPROM_SIZE_SHIFT;
/* 256B eeprom size was not supported in earlier hardware, so we
- * bump eeprom_size up one to ensure that "1" (which maps to 256B)
- * is never the result used in the shifting logic below. */
+ * bump eeprom_size up one to ensure that "1" (which maps to
+ * 256B) is never the result used in the shifting logic below.
+ */
if (eeprom_size)
eeprom_size++;
@@ -3618,8 +3658,8 @@ static void e1000_raise_ee_clk(struct e1000_hw *hw, u32 *eecd)
*/
static void e1000_lower_ee_clk(struct e1000_hw *hw, u32 *eecd)
{
- /* Lower the clock input to the EEPROM (by clearing the SK bit), and then
- * wait 50 microseconds.
+ /* Lower the clock input to the EEPROM (by clearing the SK bit), and
+ * then wait 50 microseconds.
*/
*eecd = *eecd & ~E1000_EECD_SK;
ew32(EECD, *eecd);
@@ -3651,10 +3691,11 @@ static void e1000_shift_out_ee_bits(struct e1000_hw *hw, u16 data, u16 count)
eecd |= E1000_EECD_DO;
}
do {
- /* A "1" is shifted out to the EEPROM by setting bit "DI" to a "1",
- * and then raising and then lowering the clock (the SK bit controls
- * the clock input to the EEPROM). A "0" is shifted out to the EEPROM
- * by setting "DI" to "0" and then raising and then lowering the clock.
+ /* A "1" is shifted out to the EEPROM by setting bit "DI" to a
+ * "1", and then raising and then lowering the clock (the SK bit
+ * controls the clock input to the EEPROM). A "0" is shifted
+ * out to the EEPROM by setting "DI" to "0" and then raising and
+ * then lowering the clock.
*/
eecd &= ~E1000_EECD_DI;
@@ -3691,9 +3732,9 @@ static u16 e1000_shift_in_ee_bits(struct e1000_hw *hw, u16 count)
/* In order to read a register from the EEPROM, we need to shift 'count'
* bits in from the EEPROM. Bits are "shifted in" by raising the clock
- * input to the EEPROM (setting the SK bit), and then reading the value of
- * the "DO" bit. During this "shifting in" process the "DI" bit should
- * always be clear.
+ * input to the EEPROM (setting the SK bit), and then reading the value
+ * of the "DO" bit. During this "shifting in" process the "DI" bit
+ * should always be clear.
*/
eecd = er32(EECD);
@@ -3945,8 +3986,8 @@ static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words,
if (eeprom->word_size == 0)
e1000_init_eeprom_params(hw);
- /* A check for invalid values: offset too large, too many words, and not
- * enough words.
+ /* A check for invalid values: offset too large, too many words, and
+ * not enough words.
*/
if ((offset >= eeprom->word_size)
|| (words > eeprom->word_size - offset) || (words == 0)) {
@@ -3964,7 +4005,8 @@ static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words,
return -E1000_ERR_EEPROM;
/* Set up the SPI or Microwire EEPROM for bit-bang reading. We have
- * acquired the EEPROM at this point, so any returns should release it */
+ * acquired the EEPROM at this point, so any returns should release it
+ */
if (eeprom->type == e1000_eeprom_spi) {
u16 word_in;
u8 read_opcode = EEPROM_READ_OPCODE_SPI;
@@ -3976,7 +4018,9 @@ static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words,
e1000_standby_eeprom(hw);
- /* Some SPI eeproms use the 8th address bit embedded in the opcode */
+ /* Some SPI eeproms use the 8th address bit embedded in the
+ * opcode
+ */
if ((eeprom->address_bits == 8) && (offset >= 128))
read_opcode |= EEPROM_A8_OPCODE_SPI;
@@ -3985,11 +4029,13 @@ static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words,
e1000_shift_out_ee_bits(hw, (u16) (offset * 2),
eeprom->address_bits);
- /* Read the data. The address of the eeprom internally increments with
- * each byte (spi) being read, saving on the overhead of eeprom setup
- * and tear-down. The address counter will roll over if reading beyond
- * the size of the eeprom, thus allowing the entire memory to be read
- * starting from any offset. */
+ /* Read the data. The address of the eeprom internally
+ * increments with each byte (spi) being read, saving on the
+ * overhead of eeprom setup and tear-down. The address counter
+ * will roll over if reading beyond the size of the eeprom, thus
+ * allowing the entire memory to be read starting from any
+ * offset.
+ */
for (i = 0; i < words; i++) {
word_in = e1000_shift_in_ee_bits(hw, 16);
data[i] = (word_in >> 8) | (word_in << 8);
@@ -4003,8 +4049,9 @@ static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words,
e1000_shift_out_ee_bits(hw, (u16) (offset + i),
eeprom->address_bits);
- /* Read the data. For microwire, each word requires the overhead
- * of eeprom setup and tear-down. */
+ /* Read the data. For microwire, each word requires the
+ * overhead of eeprom setup and tear-down.
+ */
data[i] = e1000_shift_in_ee_bits(hw, 16);
e1000_standby_eeprom(hw);
}
@@ -4119,8 +4166,8 @@ static s32 e1000_do_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words,
if (eeprom->word_size == 0)
e1000_init_eeprom_params(hw);
- /* A check for invalid values: offset too large, too many words, and not
- * enough words.
+ /* A check for invalid values: offset too large, too many words, and
+ * not enough words.
*/
if ((offset >= eeprom->word_size)
|| (words > eeprom->word_size - offset) || (words == 0)) {
@@ -4174,7 +4221,9 @@ static s32 e1000_write_eeprom_spi(struct e1000_hw *hw, u16 offset, u16 words,
e1000_standby_eeprom(hw);
- /* Some SPI eeproms use the 8th address bit embedded in the opcode */
+ /* Some SPI eeproms use the 8th address bit embedded in the
+ * opcode
+ */
if ((eeprom->address_bits == 8) && (offset >= 128))
write_opcode |= EEPROM_A8_OPCODE_SPI;
@@ -4186,16 +4235,19 @@ static s32 e1000_write_eeprom_spi(struct e1000_hw *hw, u16 offset, u16 words,
/* Send the data */
- /* Loop to allow for up to whole page write (32 bytes) of eeprom */
+ /* Loop to allow for up to whole page write (32 bytes) of
+ * eeprom
+ */
while (widx < words) {
u16 word_out = data[widx];
word_out = (word_out >> 8) | (word_out << 8);
e1000_shift_out_ee_bits(hw, word_out, 16);
widx++;
- /* Some larger eeprom sizes are capable of a 32-byte PAGE WRITE
- * operation, while the smaller eeproms are capable of an 8-byte
- * PAGE WRITE operation. Break the inner loop to pass new address
+ /* Some larger eeprom sizes are capable of a 32-byte
+ * PAGE WRITE operation, while the smaller eeproms are
+ * capable of an 8-byte PAGE WRITE operation. Break the
+ * inner loop to pass new address
*/
if ((((offset + widx) * 2) % eeprom->page_size) == 0) {
e1000_standby_eeprom(hw);
@@ -4249,14 +4301,15 @@ static s32 e1000_write_eeprom_microwire(struct e1000_hw *hw, u16 offset,
/* Send the data */
e1000_shift_out_ee_bits(hw, data[words_written], 16);
- /* Toggle the CS line. This in effect tells the EEPROM to execute
- * the previous command.
+ /* Toggle the CS line. This in effect tells the EEPROM to
+ * execute the previous command.
*/
e1000_standby_eeprom(hw);
- /* Read DO repeatedly until it is high (equal to '1'). The EEPROM will
- * signal that the command has been completed by raising the DO signal.
- * If DO does not go high in 10 milliseconds, then error out.
+ /* Read DO repeatedly until it is high (equal to '1'). The
+ * EEPROM will signal that the command has been completed by
+ * raising the DO signal. If DO does not go high in 10
+ * milliseconds, then error out.
*/
for (i = 0; i < 200; i++) {
eecd = er32(EECD);
@@ -4483,7 +4536,8 @@ static void e1000_clear_vfta(struct e1000_hw *hw)
for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) {
/* If the offset we want to clear is the same offset of the
* manageability VLAN ID, then clear all bits except that of the
- * manageability unit */
+ * manageability unit
+ */
vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0;
E1000_WRITE_REG_ARRAY(hw, VFTA, offset, vfta_value);
E1000_WRITE_FLUSH();
@@ -4911,12 +4965,12 @@ void e1000_tbi_adjust_stats(struct e1000_hw *hw, struct e1000_hw_stats *stats,
* counters overcount this packet as a CRC error and undercount
* the packet as a good packet
*/
- /* This packet should not be counted as a CRC error. */
+ /* This packet should not be counted as a CRC error. */
stats->crcerrs--;
- /* This packet does count as a Good Packet Received. */
+ /* This packet does count as a Good Packet Received. */
stats->gprc++;
- /* Adjust the Good Octets received counters */
+ /* Adjust the Good Octets received counters */
carry_bit = 0x80000000 & stats->gorcl;
stats->gorcl += frame_len;
/* If the high bit of Gorcl (the low 32 bits of the Good Octets
@@ -5196,8 +5250,9 @@ static s32 e1000_check_polarity(struct e1000_hw *hw,
if (ret_val)
return ret_val;
- /* If speed is 1000 Mbps, must read the IGP01E1000_PHY_PCS_INIT_REG to
- * find the polarity status */
+ /* If speed is 1000 Mbps, must read the
+ * IGP01E1000_PHY_PCS_INIT_REG to find the polarity status
+ */
if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) ==
IGP01E1000_PSSR_SPEED_1000MBPS) {
@@ -5213,8 +5268,9 @@ static s32 e1000_check_polarity(struct e1000_hw *hw,
e1000_rev_polarity_reversed :
e1000_rev_polarity_normal;
} else {
- /* For 10 Mbps, read the polarity bit in the status register. (for
- * 100 Mbps this bit is always 0) */
+ /* For 10 Mbps, read the polarity bit in the status
+ * register. (for 100 Mbps this bit is always 0)
+ */
*polarity =
(phy_data & IGP01E1000_PSSR_POLARITY_REVERSED) ?
e1000_rev_polarity_reversed :
@@ -5374,8 +5430,9 @@ static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw, bool link_up)
}
} else {
if (hw->dsp_config_state == e1000_dsp_config_activated) {
- /* Save off the current value of register 0x2F5B to be restored at
- * the end of the routines. */
+ /* Save off the current value of register 0x2F5B to be
+ * restored at the end of the routines.
+ */
ret_val =
e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
@@ -5391,7 +5448,7 @@ static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw, bool link_up)
msleep(20);
ret_val = e1000_write_phy_reg(hw, 0x0000,
- IGP01E1000_IEEE_FORCE_GIGA);
+ IGP01E1000_IEEE_FORCE_GIGA);
if (ret_val)
return ret_val;
for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) {
@@ -5412,7 +5469,7 @@ static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw, bool link_up)
}
ret_val = e1000_write_phy_reg(hw, 0x0000,
- IGP01E1000_IEEE_RESTART_AUTONEG);
+ IGP01E1000_IEEE_RESTART_AUTONEG);
if (ret_val)
return ret_val;
@@ -5429,8 +5486,9 @@ static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw, bool link_up)
}
if (hw->ffe_config_state == e1000_ffe_config_active) {
- /* Save off the current value of register 0x2F5B to be restored at
- * the end of the routines. */
+ /* Save off the current value of register 0x2F5B to be
+ * restored at the end of the routines.
+ */
ret_val =
e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data);
@@ -5446,7 +5504,7 @@ static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw, bool link_up)
msleep(20);
ret_val = e1000_write_phy_reg(hw, 0x0000,
- IGP01E1000_IEEE_FORCE_GIGA);
+ IGP01E1000_IEEE_FORCE_GIGA);
if (ret_val)
return ret_val;
ret_val =
@@ -5456,7 +5514,7 @@ static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw, bool link_up)
return ret_val;
ret_val = e1000_write_phy_reg(hw, 0x0000,
- IGP01E1000_IEEE_RESTART_AUTONEG);
+ IGP01E1000_IEEE_RESTART_AUTONEG);
if (ret_val)
return ret_val;
@@ -5542,8 +5600,9 @@ static s32 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active)
return E1000_SUCCESS;
/* During driver activity LPLU should not be used or it will attain link
- * from the lowest speeds starting from 10Mbps. The capability is used for
- * Dx transitions and states */
+ * from the lowest speeds starting from 10Mbps. The capability is used
+ * for Dx transitions and states
+ */
if (hw->mac_type == e1000_82541_rev_2
|| hw->mac_type == e1000_82547_rev_2) {
ret_val =
@@ -5563,10 +5622,11 @@ static s32 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active)
return ret_val;
}
- /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during
- * Dx states where the power conservation is most important. During
- * driver activity we should enable SmartSpeed, so performance is
- * maintained. */
+ /* LPLU and SmartSpeed are mutually exclusive. LPLU is used
+ * during Dx states where the power conservation is most
+ * important. During driver activity we should enable
+ * SmartSpeed, so performance is maintained.
+ */
if (hw->smart_speed == e1000_smart_speed_on) {
ret_val =
e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
diff --git a/drivers/net/ethernet/intel/e1000/e1000_main.c b/drivers/net/ethernet/intel/e1000/e1000_main.c
index d947e3aae1e8..8502c625dbef 100644
--- a/drivers/net/ethernet/intel/e1000/e1000_main.c
+++ b/drivers/net/ethernet/intel/e1000/e1000_main.c
@@ -239,7 +239,6 @@ struct net_device *e1000_get_hw_dev(struct e1000_hw *hw)
* e1000_init_module is the first routine called when the driver is
* loaded. All it does is register with the PCI subsystem.
**/
-
static int __init e1000_init_module(void)
{
int ret;
@@ -266,7 +265,6 @@ module_init(e1000_init_module);
* e1000_exit_module is called just before the driver is removed
* from memory.
**/
-
static void __exit e1000_exit_module(void)
{
pci_unregister_driver(&e1000_driver);
@@ -301,7 +299,6 @@ static void e1000_free_irq(struct e1000_adapter *adapter)
* e1000_irq_disable - Mask off interrupt generation on the NIC
* @adapter: board private structure
**/
-
static void e1000_irq_disable(struct e1000_adapter *adapter)
{
struct e1000_hw *hw = &adapter->hw;
@@ -315,7 +312,6 @@ static void e1000_irq_disable(struct e1000_adapter *adapter)
* e1000_irq_enable - Enable default interrupt generation settings
* @adapter: board private structure
**/
-
static void e1000_irq_enable(struct e1000_adapter *adapter)
{
struct e1000_hw *hw = &adapter->hw;
@@ -398,11 +394,12 @@ static void e1000_configure(struct e1000_adapter *adapter)
e1000_configure_rx(adapter);
/* call E1000_DESC_UNUSED which always leaves
* at least 1 descriptor unused to make sure
- * next_to_use != next_to_clean */
+ * next_to_use != next_to_clean
+ */
for (i = 0; i < adapter->num_rx_queues; i++) {
struct e1000_rx_ring *ring = &adapter->rx_ring[i];
adapter->alloc_rx_buf(adapter, ring,
- E1000_DESC_UNUSED(ring));
+ E1000_DESC_UNUSED(ring));
}
}
@@ -433,9 +430,7 @@ int e1000_up(struct e1000_adapter *adapter)
* The phy may be powered down to save power and turn off link when the
* driver is unloaded and wake on lan is not enabled (among others)
* *** this routine MUST be followed by a call to e1000_reset ***
- *
**/
-
void e1000_power_up_phy(struct e1000_adapter *adapter)
{
struct e1000_hw *hw = &adapter->hw;
@@ -444,7 +439,8 @@ void e1000_power_up_phy(struct e1000_adapter *adapter)
/* Just clear the power down bit to wake the phy back up */
if (hw->media_type == e1000_media_type_copper) {
/* according to the manual, the phy will retain its
- * settings across a power-down/up cycle */
+ * settings across a power-down/up cycle
+ */
e1000_read_phy_reg(hw, PHY_CTRL, &mii_reg);
mii_reg &= ~MII_CR_POWER_DOWN;
e1000_write_phy_reg(hw, PHY_CTRL, mii_reg);
@@ -459,7 +455,8 @@ static void e1000_power_down_phy(struct e1000_adapter *adapter)
* The PHY cannot be powered down if any of the following is true *
* (a) WoL is enabled
* (b) AMT is active
- * (c) SoL/IDER session is active */
+ * (c) SoL/IDER session is active
+ */
if (!adapter->wol && hw->mac_type >= e1000_82540 &&
hw->media_type == e1000_media_type_copper) {
u16 mii_reg = 0;
@@ -529,8 +526,7 @@ void e1000_down(struct e1000_adapter *adapter)
e1000_irq_disable(adapter);
- /*
- * Setting DOWN must be after irq_disable to prevent
+ /* Setting DOWN must be after irq_disable to prevent
* a screaming interrupt. Setting DOWN also prevents
* tasks from rescheduling.
*/
@@ -627,14 +623,14 @@ void e1000_reset(struct e1000_adapter *adapter)
* rounded up to the next 1KB and expressed in KB. Likewise,
* the Rx FIFO should be large enough to accommodate at least
* one full receive packet and is similarly rounded up and
- * expressed in KB. */
+ * expressed in KB.
+ */
pba = er32(PBA);
/* upper 16 bits has Tx packet buffer allocation size in KB */
tx_space = pba >> 16;
/* lower 16 bits has Rx packet buffer allocation size in KB */
pba &= 0xffff;
- /*
- * the tx fifo also stores 16 bytes of information about the tx
+ /* the Tx fifo also stores 16 bytes of information about the Tx
* but don't include ethernet FCS because hardware appends it
*/
min_tx_space = (hw->max_frame_size +
@@ -649,7 +645,8 @@ void e1000_reset(struct e1000_adapter *adapter)
/* If current Tx allocation is less than the min Tx FIFO size,
* and the min Tx FIFO size is less than the current Rx FIFO
- * allocation, take space away from current Rx allocation */
+ * allocation, take space away from current Rx allocation
+ */
if (tx_space < min_tx_space &&
((min_tx_space - tx_space) < pba)) {
pba = pba - (min_tx_space - tx_space);
@@ -663,8 +660,9 @@ void e1000_reset(struct e1000_adapter *adapter)
break;
}
- /* if short on rx space, rx wins and must trump tx
- * adjustment or use Early Receive if available */
+ /* if short on Rx space, Rx wins and must trump Tx
+ * adjustment or use Early Receive if available
+ */
if (pba < min_rx_space)
pba = min_rx_space;
}
@@ -672,8 +670,7 @@ void e1000_reset(struct e1000_adapter *adapter)
ew32(PBA, pba);
- /*
- * flow control settings:
+ /* flow control settings:
* The high water mark must be low enough to fit one full frame
* (or the size used for early receive) above it in the Rx FIFO.
* Set it to the lower of:
@@ -707,7 +704,8 @@ void e1000_reset(struct e1000_adapter *adapter)
u32 ctrl = er32(CTRL);
/* clear phy power management bit if we are in gig only mode,
* which if enabled will attempt negotiation to 100Mb, which
- * can cause a loss of link at power off or driver unload */
+ * can cause a loss of link at power off or driver unload
+ */
ctrl &= ~E1000_CTRL_SWDPIN3;
ew32(CTRL, ctrl);
}
@@ -808,9 +806,8 @@ static int e1000_is_need_ioport(struct pci_dev *pdev)
static netdev_features_t e1000_fix_features(struct net_device *netdev,
netdev_features_t features)
{
- /*
- * Since there is no support for separate rx/tx vlan accel
- * enable/disable make sure tx flag is always in same state as rx.
+ /* Since there is no support for separate Rx/Tx vlan accel
+ * enable/disable make sure Tx flag is always in same state as Rx.
*/
if (features & NETIF_F_HW_VLAN_RX)
features |= NETIF_F_HW_VLAN_TX;
@@ -1012,16 +1009,14 @@ static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
if (err)
goto err_sw_init;
- /*
- * there is a workaround being applied below that limits
+ /* there is a workaround being applied below that limits
* 64-bit DMA addresses to 64-bit hardware. There are some
* 32-bit adapters that Tx hang when given 64-bit DMA addresses
*/
pci_using_dac = 0;
if ((hw->bus_type == e1000_bus_type_pcix) &&
!dma_set_mask(&pdev->dev, DMA_BIT_MASK(64))) {
- /*
- * according to DMA-API-HOWTO, coherent calls will always
+ /* according to DMA-API-HOWTO, coherent calls will always
* succeed if the set call did
*/
dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64));
@@ -1099,7 +1094,8 @@ static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
}
/* before reading the EEPROM, reset the controller to
- * put the device in a known good starting state */
+ * put the device in a known good starting state
+ */
e1000_reset_hw(hw);
@@ -1107,8 +1103,7 @@ static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
if (e1000_validate_eeprom_checksum(hw) < 0) {
e_err(probe, "The EEPROM Checksum Is Not Valid\n");
e1000_dump_eeprom(adapter);
- /*
- * set MAC address to all zeroes to invalidate and temporary
+ /* set MAC address to all zeroes to invalidate and temporary
* disable this device for the user. This blocks regular
* traffic while still permitting ethtool ioctls from reaching
* the hardware as well as allowing the user to run the
@@ -1169,7 +1164,8 @@ static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
/* now that we have the eeprom settings, apply the special cases
* where the eeprom may be wrong or the board simply won't support
- * wake on lan on a particular port */
+ * wake on lan on a particular port
+ */
switch (pdev->device) {
case E1000_DEV_ID_82546GB_PCIE:
adapter->eeprom_wol = 0;
@@ -1177,7 +1173,8 @@ static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
case E1000_DEV_ID_82546EB_FIBER:
case E1000_DEV_ID_82546GB_FIBER:
/* Wake events only supported on port A for dual fiber
- * regardless of eeprom setting */
+ * regardless of eeprom setting
+ */
if (er32(STATUS) & E1000_STATUS_FUNC_1)
adapter->eeprom_wol = 0;
break;
@@ -1270,7 +1267,6 @@ err_pci_reg:
* Hot-Plug event, or because the driver is going to be removed from
* memory.
**/
-
static void e1000_remove(struct pci_dev *pdev)
{
struct net_device *netdev = pci_get_drvdata(pdev);
@@ -1306,7 +1302,6 @@ static void e1000_remove(struct pci_dev *pdev)
* e1000_sw_init initializes the Adapter private data structure.
* e1000_init_hw_struct MUST be called before this function
**/
-
static int e1000_sw_init(struct e1000_adapter *adapter)
{
adapter->rx_buffer_len = MAXIMUM_ETHERNET_VLAN_SIZE;
@@ -1337,7 +1332,6 @@ static int e1000_sw_init(struct e1000_adapter *adapter)
* We allocate one ring per queue at run-time since we don't know the
* number of queues at compile-time.
**/
-
static int e1000_alloc_queues(struct e1000_adapter *adapter)
{
adapter->tx_ring = kcalloc(adapter->num_tx_queues,
@@ -1367,7 +1361,6 @@ static int e1000_alloc_queues(struct e1000_adapter *adapter)
* handler is registered with the OS, the watchdog task is started,
* and the stack is notified that the interface is ready.
**/
-
static int e1000_open(struct net_device *netdev)
{
struct e1000_adapter *adapter = netdev_priv(netdev);
@@ -1401,7 +1394,8 @@ static int e1000_open(struct net_device *netdev)
/* before we allocate an interrupt, we must be ready to handle it.
* Setting DEBUG_SHIRQ in the kernel makes it fire an interrupt
* as soon as we call pci_request_irq, so we have to setup our
- * clean_rx handler before we do so. */
+ * clean_rx handler before we do so.
+ */
e1000_configure(adapter);
err = e1000_request_irq(adapter);
@@ -1444,7 +1438,6 @@ err_setup_tx:
* needs to be disabled. A global MAC reset is issued to stop the
* hardware, and all transmit and receive resources are freed.
**/
-
static int e1000_close(struct net_device *netdev)
{
struct e1000_adapter *adapter = netdev_priv(netdev);
@@ -1459,10 +1452,11 @@ static int e1000_close(struct net_device *netdev)
e1000_free_all_rx_resources(adapter);
/* kill manageability vlan ID if supported, but not if a vlan with
- * the same ID is registered on the host OS (let 8021q kill it) */
+ * the same ID is registered on the host OS (let 8021q kill it)
+ */
if ((hw->mng_cookie.status &
- E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT) &&
- !test_bit(adapter->mng_vlan_id, adapter->active_vlans)) {
+ E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT) &&
+ !test_bit(adapter->mng_vlan_id, adapter->active_vlans)) {
e1000_vlan_rx_kill_vid(netdev, adapter->mng_vlan_id);
}
@@ -1483,7 +1477,8 @@ static bool e1000_check_64k_bound(struct e1000_adapter *adapter, void *start,
unsigned long end = begin + len;
/* First rev 82545 and 82546 need to not allow any memory
- * write location to cross 64k boundary due to errata 23 */
+ * write location to cross 64k boundary due to errata 23
+ */
if (hw->mac_type == e1000_82545 ||
hw->mac_type == e1000_ce4100 ||
hw->mac_type == e1000_82546) {
@@ -1500,7 +1495,6 @@ static bool e1000_check_64k_bound(struct e1000_adapter *adapter, void *start,
*
* Return 0 on success, negative on failure
**/
-
static int e1000_setup_tx_resources(struct e1000_adapter *adapter,
struct e1000_tx_ring *txdr)
{
@@ -1574,7 +1568,6 @@ setup_tx_desc_die:
*
* Return 0 on success, negative on failure
**/
-
int e1000_setup_all_tx_resources(struct e1000_adapter *adapter)
{
int i, err = 0;
@@ -1599,7 +1592,6 @@ int e1000_setup_all_tx_resources(struct e1000_adapter *adapter)
*
* Configure the Tx unit of the MAC after a reset.
**/
-
static void e1000_configure_tx(struct e1000_adapter *adapter)
{
u64 tdba;
@@ -1620,8 +1612,10 @@ static void e1000_configure_tx(struct e1000_adapter *adapter)
ew32(TDBAL, (tdba & 0x00000000ffffffffULL));
ew32(TDT, 0);
ew32(TDH, 0);
- adapter->tx_ring[0].tdh = ((hw->mac_type >= e1000_82543) ? E1000_TDH : E1000_82542_TDH);
- adapter->tx_ring[0].tdt = ((hw->mac_type >= e1000_82543) ? E1000_TDT : E1000_82542_TDT);
+ adapter->tx_ring[0].tdh = ((hw->mac_type >= e1000_82543) ?
+ E1000_TDH : E1000_82542_TDH);
+ adapter->tx_ring[0].tdt = ((hw->mac_type >= e1000_82543) ?
+ E1000_TDT : E1000_82542_TDT);
break;
}
@@ -1676,7 +1670,8 @@ static void e1000_configure_tx(struct e1000_adapter *adapter)
adapter->txd_cmd |= E1000_TXD_CMD_RS;
/* Cache if we're 82544 running in PCI-X because we'll
- * need this to apply a workaround later in the send path. */
+ * need this to apply a workaround later in the send path.
+ */
if (hw->mac_type == e1000_82544 &&
hw->bus_type == e1000_bus_type_pcix)
adapter->pcix_82544 = true;
@@ -1692,7 +1687,6 @@ static void e1000_configure_tx(struct e1000_adapter *adapter)
*
* Returns 0 on success, negative on failure
**/
-
static int e1000_setup_rx_resources(struct e1000_adapter *adapter,
struct e1000_rx_ring *rxdr)
{
@@ -1771,7 +1765,6 @@ setup_rx_desc_die:
*
* Return 0 on success, negative on failure
**/
-
int e1000_setup_all_rx_resources(struct e1000_adapter *adapter)
{
int i, err = 0;
@@ -1840,7 +1833,8 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
/* This is useful for sniffing bad packets. */
if (adapter->netdev->features & NETIF_F_RXALL) {
/* UPE and MPE will be handled by normal PROMISC logic
- * in e1000e_set_rx_mode */
+ * in e1000e_set_rx_mode
+ */
rctl |= (E1000_RCTL_SBP | /* Receive bad packets */
E1000_RCTL_BAM | /* RX All Bcast Pkts */
E1000_RCTL_PMCF); /* RX All MAC Ctrl Pkts */
@@ -1862,7 +1856,6 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
*
* Configure the Rx unit of the MAC after a reset.
**/
-
static void e1000_configure_rx(struct e1000_adapter *adapter)
{
u64 rdba;
@@ -1895,7 +1888,8 @@ static void e1000_configure_rx(struct e1000_adapter *adapter)
}
/* Setup the HW Rx Head and Tail Descriptor Pointers and
- * the Base and Length of the Rx Descriptor Ring */
+ * the Base and Length of the Rx Descriptor Ring
+ */
switch (adapter->num_rx_queues) {
case 1:
default:
@@ -1905,8 +1899,10 @@ static void e1000_configure_rx(struct e1000_adapter *adapter)
ew32(RDBAL, (rdba & 0x00000000ffffffffULL));
ew32(RDT, 0);
ew32(RDH, 0);
- adapter->rx_ring[0].rdh = ((hw->mac_type >= e1000_82543) ? E1000_RDH : E1000_82542_RDH);
- adapter->rx_ring[0].rdt = ((hw->mac_type >= e1000_82543) ? E1000_RDT : E1000_82542_RDT);
+ adapter->rx_ring[0].rdh = ((hw->mac_type >= e1000_82543) ?
+ E1000_RDH : E1000_82542_RDH);
+ adapter->rx_ring[0].rdt = ((hw->mac_type >= e1000_82543) ?
+ E1000_RDT : E1000_82542_RDT);
break;
}
@@ -1932,7 +1928,6 @@ static void e1000_configure_rx(struct e1000_adapter *adapter)
*
* Free all transmit software resources
**/
-
static void e1000_free_tx_resources(struct e1000_adapter *adapter,
struct e1000_tx_ring *tx_ring)
{
@@ -1955,7 +1950,6 @@ static void e1000_free_tx_resources(struct e1000_adapter *adapter,
*
* Free all transmit software resources
**/
-
void e1000_free_all_tx_resources(struct e1000_adapter *adapter)
{
int i;
@@ -1990,7 +1984,6 @@ static void e1000_unmap_and_free_tx_resource(struct e1000_adapter *adapter,
* @adapter: board private structure
* @tx_ring: ring to be cleaned
**/
-
static void e1000_clean_tx_ring(struct e1000_adapter *adapter,
struct e1000_tx_ring *tx_ring)
{
@@ -2026,7 +2019,6 @@ static void e1000_clean_tx_ring(struct e1000_adapter *adapter,
* e1000_clean_all_tx_rings - Free Tx Buffers for all queues
* @adapter: board private structure
**/
-
static void e1000_clean_all_tx_rings(struct e1000_adapter *adapter)
{
int i;
@@ -2042,7 +2034,6 @@ static void e1000_clean_all_tx_rings(struct e1000_adapter *adapter)
*
* Free all receive software resources
**/
-
static void e1000_free_rx_resources(struct e1000_adapter *adapter,
struct e1000_rx_ring *rx_ring)
{
@@ -2065,7 +2056,6 @@ static void e1000_free_rx_resources(struct e1000_adapter *adapter,
*
* Free all receive software resources
**/
-
void e1000_free_all_rx_resources(struct e1000_adapter *adapter)
{
int i;
@@ -2079,7 +2069,6 @@ void e1000_free_all_rx_resources(struct e1000_adapter *adapter)
* @adapter: board private structure
* @rx_ring: ring to free buffers from
**/
-
static void e1000_clean_rx_ring(struct e1000_adapter *adapter,
struct e1000_rx_ring *rx_ring)
{
@@ -2138,7 +2127,6 @@ static void e1000_clean_rx_ring(struct e1000_adapter *adapter,
* e1000_clean_all_rx_rings - Free Rx Buffers for all queues
* @adapter: board private structure
**/
-
static void e1000_clean_all_rx_rings(struct e1000_adapter *adapter)
{
int i;
@@ -2198,7 +2186,6 @@ static void e1000_leave_82542_rst(struct e1000_adapter *adapter)
*
* Returns 0 on success, negative on failure
**/
-
static int e1000_set_mac(struct net_device *netdev, void *p)
{
struct e1000_adapter *adapter = netdev_priv(netdev);
@@ -2233,7 +2220,6 @@ static int e1000_set_mac(struct net_device *netdev, void *p)
* responsible for configuring the hardware for proper unicast, multicast,
* promiscuous mode, and all-multi behavior.
**/
-
static void e1000_set_rx_mode(struct net_device *netdev)
{
struct e1000_adapter *adapter = netdev_priv(netdev);
@@ -2317,10 +2303,10 @@ static void e1000_set_rx_mode(struct net_device *netdev)
}
/* write the hash table completely, write from bottom to avoid
- * both stupid write combining chipsets, and flushing each write */
+ * both stupid write combining chipsets, and flushing each write
+ */
for (i = mta_reg_count - 1; i >= 0 ; i--) {
- /*
- * If we are on an 82544 has an errata where writing odd
+ /* If we are on an 82544 has an errata where writing odd
* offsets overwrites the previous even offset, but writing
* backwards over the range solves the issue by always
* writing the odd offset first
@@ -2458,8 +2444,8 @@ static void e1000_watchdog(struct work_struct *work)
bool txb2b = true;
/* update snapshot of PHY registers on LSC */
e1000_get_speed_and_duplex(hw,
- &adapter->link_speed,
- &adapter->link_duplex);
+ &adapter->link_speed,
+ &adapter->link_duplex);
ctrl = er32(CTRL);
pr_info("%s NIC Link is Up %d Mbps %s, "
@@ -2533,7 +2519,8 @@ link_up:
/* We've lost link, so the controller stops DMA,
* but we've got queued Tx work that's never going
* to get done, so reset controller to flush Tx.
- * (Do the reset outside of interrupt context). */
+ * (Do the reset outside of interrupt context).
+ */
adapter->tx_timeout_count++;
schedule_work(&adapter->reset_task);
/* exit immediately since reset is imminent */
@@ -2543,8 +2530,7 @@ link_up:
/* Simple mode for Interrupt Throttle Rate (ITR) */
if (hw->mac_type >= e1000_82540 && adapter->itr_setting == 4) {
- /*
- * Symmetric Tx/Rx gets a reduced ITR=2000;
+ /* Symmetric Tx/Rx gets a reduced ITR=2000;
* Total asymmetrical Tx or Rx gets ITR=8000;
* everyone else is between 2000-8000.
*/
@@ -2659,18 +2645,16 @@ static void e1000_set_itr(struct e1000_adapter *adapter)
goto set_itr_now;
}
- adapter->tx_itr = e1000_update_itr(adapter,
- adapter->tx_itr,
- adapter->total_tx_packets,
- adapter->total_tx_bytes);
+ adapter->tx_itr = e1000_update_itr(adapter, adapter->tx_itr,
+ adapter->total_tx_packets,
+ adapter->total_tx_bytes);
/* conservative mode (itr 3) eliminates the lowest_latency setting */
if (adapter->itr_setting == 3 && adapter->tx_itr == lowest_latency)
adapter->tx_itr = low_latency;
- adapter->rx_itr = e1000_update_itr(adapter,
- adapter->rx_itr,
- adapter->total_rx_packets,
- adapter->total_rx_bytes);
+ adapter->rx_itr = e1000_update_itr(adapter, adapter->rx_itr,
+ adapter->total_rx_packets,
+ adapter->total_rx_bytes);
/* conservative mode (itr 3) eliminates the lowest_latency setting */
if (adapter->itr_setting == 3 && adapter->rx_itr == lowest_latency)
adapter->rx_itr = low_latency;
@@ -2696,10 +2680,11 @@ set_itr_now:
if (new_itr != adapter->itr) {
/* this attempts to bias the interrupt rate towards Bulk
* by adding intermediate steps when interrupt rate is
- * increasing */
+ * increasing
+ */
new_itr = new_itr > adapter->itr ?
- min(adapter->itr + (new_itr >> 2), new_itr) :
- new_itr;
+ min(adapter->itr + (new_itr >> 2), new_itr) :
+ new_itr;
adapter->itr = new_itr;
ew32(ITR, 1000000000 / (new_itr * 256));
}
@@ -2861,7 +2846,8 @@ static int e1000_tx_map(struct e1000_adapter *adapter,
/* Workaround for Controller erratum --
* descriptor for non-tso packet in a linear SKB that follows a
* tso gets written back prematurely before the data is fully
- * DMA'd to the controller */
+ * DMA'd to the controller
+ */
if (!skb->data_len && tx_ring->last_tx_tso &&
!skb_is_gso(skb)) {
tx_ring->last_tx_tso = false;
@@ -2869,7 +2855,8 @@ static int e1000_tx_map(struct e1000_adapter *adapter,
}
/* Workaround for premature desc write-backs
- * in TSO mode. Append 4-byte sentinel desc */
+ * in TSO mode. Append 4-byte sentinel desc
+ */
if (unlikely(mss && !nr_frags && size == len && size > 8))
size -= 4;
/* work-around for errata 10 and it applies
@@ -2882,7 +2869,8 @@ static int e1000_tx_map(struct e1000_adapter *adapter,
size = 2015;
/* Workaround for potential 82544 hang in PCI-X. Avoid
- * terminating buffers within evenly-aligned dwords. */
+ * terminating buffers within evenly-aligned dwords.
+ */
if (unlikely(adapter->pcix_82544 &&
!((unsigned long)(skb->data + offset + size - 1) & 4) &&
size > 4))
@@ -2894,7 +2882,7 @@ static int e1000_tx_map(struct e1000_adapter *adapter,
buffer_info->mapped_as_page = false;
buffer_info->dma = dma_map_single(&pdev->dev,
skb->data + offset,
- size, DMA_TO_DEVICE);
+ size, DMA_TO_DEVICE);
if (dma_mapping_error(&pdev->dev, buffer_info->dma))
goto dma_error;
buffer_info->next_to_watch = i;
@@ -2925,12 +2913,15 @@ static int e1000_tx_map(struct e1000_adapter *adapter,
buffer_info = &tx_ring->buffer_info[i];
size = min(len, max_per_txd);
/* Workaround for premature desc write-backs
- * in TSO mode. Append 4-byte sentinel desc */
- if (unlikely(mss && f == (nr_frags-1) && size == len && size > 8))
+ * in TSO mode. Append 4-byte sentinel desc
+ */
+ if (unlikely(mss && f == (nr_frags-1) &&
+ size == len && size > 8))
size -= 4;
/* Workaround for potential 82544 hang in PCI-X.
* Avoid terminating buffers within evenly-aligned
- * dwords. */
+ * dwords.
+ */
bufend = (unsigned long)
page_to_phys(skb_frag_page(frag));
bufend += offset + size - 1;
@@ -2994,7 +2985,7 @@ static void e1000_tx_queue(struct e1000_adapter *adapter,
if (likely(tx_flags & E1000_TX_FLAGS_TSO)) {
txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D |
- E1000_TXD_CMD_TSE;
+ E1000_TXD_CMD_TSE;
txd_upper |= E1000_TXD_POPTS_TXSM << 8;
if (likely(tx_flags & E1000_TX_FLAGS_IPV4))
@@ -3035,13 +3026,15 @@ static void e1000_tx_queue(struct e1000_adapter *adapter,
/* Force memory writes to complete before letting h/w
* know there are new descriptors to fetch. (Only
* applicable for weak-ordered memory model archs,
- * such as IA-64). */
+ * such as IA-64).
+ */
wmb();
tx_ring->next_to_use = i;
writel(i, hw->hw_addr + tx_ring->tdt);
/* we need this if more than one processor can write to our tail
- * at a time, it syncronizes IO on IA64/Altix systems */
+ * at a time, it synchronizes IO on IA64/Altix systems
+ */
mmiowb();
}
@@ -3090,11 +3083,13 @@ static int __e1000_maybe_stop_tx(struct net_device *netdev, int size)
netif_stop_queue(netdev);
/* Herbert's original patch had:
* smp_mb__after_netif_stop_queue();
- * but since that doesn't exist yet, just open code it. */
+ * but since that doesn't exist yet, just open code it.
+ */
smp_mb();
/* We need to check again in a case another CPU has just
- * made room available. */
+ * made room available.
+ */
if (likely(E1000_DESC_UNUSED(tx_ring) < size))
return -EBUSY;
@@ -3105,7 +3100,7 @@ static int __e1000_maybe_stop_tx(struct net_device *netdev, int size)
}
static int e1000_maybe_stop_tx(struct net_device *netdev,
- struct e1000_tx_ring *tx_ring, int size)
+ struct e1000_tx_ring *tx_ring, int size)
{
if (likely(E1000_DESC_UNUSED(tx_ring) >= size))
return 0;
@@ -3129,10 +3124,11 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb,
int tso;
unsigned int f;
- /* This goes back to the question of how to logically map a tx queue
+ /* This goes back to the question of how to logically map a Tx queue
* to a flow. Right now, performance is impacted slightly negatively
- * if using multiple tx queues. If the stack breaks away from a
- * single qdisc implementation, we can look at this again. */
+ * if using multiple Tx queues. If the stack breaks away from a
+ * single qdisc implementation, we can look at this again.
+ */
tx_ring = adapter->tx_ring;
if (unlikely(skb->len <= 0)) {
@@ -3157,7 +3153,8 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb,
* initiating the DMA for each buffer. The calc is:
* 4 = ceil(buffer len/mss). To make sure we don't
* overrun the FIFO, adjust the max buffer len if mss
- * drops. */
+ * drops.
+ */
if (mss) {
u8 hdr_len;
max_per_txd = min(mss << 2, max_per_txd);
@@ -3173,8 +3170,10 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb,
* this hardware's requirements
* NOTE: this is a TSO only workaround
* if end byte alignment not correct move us
- * into the next dword */
- if ((unsigned long)(skb_tail_pointer(skb) - 1) & 4)
+ * into the next dword
+ */
+ if ((unsigned long)(skb_tail_pointer(skb) - 1)
+ & 4)
break;
/* fall through */
pull_size = min((unsigned int)4, skb->data_len);
@@ -3222,7 +3221,8 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb,
count += nr_frags;
/* need: count + 2 desc gap to keep tail from touching
- * head, otherwise try next time */
+ * head, otherwise try next time
+ */
if (unlikely(e1000_maybe_stop_tx(netdev, tx_ring, count + 2)))
return NETDEV_TX_BUSY;
@@ -3261,7 +3261,7 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb,
tx_flags |= E1000_TX_FLAGS_NO_FCS;
count = e1000_tx_map(adapter, tx_ring, skb, first, max_per_txd,
- nr_frags, mss);
+ nr_frags, mss);
if (count) {
netdev_sent_queue(netdev, skb->len);
@@ -3363,9 +3363,7 @@ static void e1000_dump(struct e1000_adapter *adapter)
/* Print Registers */
e1000_regdump(adapter);
- /*
- * transmit dump
- */
+ /* transmit dump */
pr_info("TX Desc ring0 dump\n");
/* Transmit Descriptor Formats - DEXT[29] is 0 (Legacy) or 1 (Extended)
@@ -3426,9 +3424,7 @@ static void e1000_dump(struct e1000_adapter *adapter)
}
rx_ring_summary:
- /*
- * receive dump
- */
+ /* receive dump */
pr_info("\nRX Desc ring dump\n");
/* Legacy Receive Descriptor Format
@@ -3493,7 +3489,6 @@ exit:
* e1000_tx_timeout - Respond to a Tx Hang
* @netdev: network interface device structure
**/
-
static void e1000_tx_timeout(struct net_device *netdev)
{
struct e1000_adapter *adapter = netdev_priv(netdev);
@@ -3521,7 +3516,6 @@ static void e1000_reset_task(struct work_struct *work)
* Returns the address of the device statistics structure.
* The statistics are actually updated from the watchdog.
**/
-
static struct net_device_stats *e1000_get_stats(struct net_device *netdev)
{
/* only return the current stats */
@@ -3535,7 +3529,6 @@ static struct net_device_stats *e1000_get_stats(struct net_device *netdev)
*
* Returns 0 on success, negative on failure
**/
-
static int e1000_change_mtu(struct net_device *netdev, int new_mtu)
{
struct e1000_adapter *adapter = netdev_priv(netdev);
@@ -3572,8 +3565,9 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu)
* means we reserve 2 more, this pushes us to allocate from the next
* larger slab size.
* i.e. RXBUFFER_2048 --> size-4096 slab
- * however with the new *_jumbo_rx* routines, jumbo receives will use
- * fragmented skbs */
+ * however with the new *_jumbo_rx* routines, jumbo receives will use
+ * fragmented skbs
+ */
if (max_frame <= E1000_RXBUFFER_2048)
adapter->rx_buffer_len = E1000_RXBUFFER_2048;
@@ -3608,7 +3602,6 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu)
* e1000_update_stats - Update the board statistics counters
* @adapter: board private structure
**/
-
void e1000_update_stats(struct e1000_adapter *adapter)
{
struct net_device *netdev = adapter->netdev;
@@ -3619,8 +3612,7 @@ void e1000_update_stats(struct e1000_adapter *adapter)
#define PHY_IDLE_ERROR_COUNT_MASK 0x00FF
- /*
- * Prevent stats update while adapter is being reset, or if the pci
+ /* Prevent stats update while adapter is being reset, or if the pci
* connection is down.
*/
if (adapter->link_speed == 0)
@@ -3710,7 +3702,8 @@ void e1000_update_stats(struct e1000_adapter *adapter)
/* Rx Errors */
/* RLEC on some newer hardware can be incorrect so build
- * our own version based on RUC and ROC */
+ * our own version based on RUC and ROC
+ */
netdev->stats.rx_errors = adapter->stats.rxerrc +
adapter->stats.crcerrs + adapter->stats.algnerrc +
adapter->stats.ruc + adapter->stats.roc +
@@ -3764,7 +3757,6 @@ void e1000_update_stats(struct e1000_adapter *adapter)
* @irq: interrupt number
* @data: pointer to a network interface device structure
**/
-
static irqreturn_t e1000_intr(int irq, void *data)
{
struct net_device *netdev = data;
@@ -3775,8 +3767,7 @@ static irqreturn_t e1000_intr(int irq, void *data)
if (unlikely((!icr)))
return IRQ_NONE; /* Not our interrupt */
- /*
- * we might have caused the interrupt, but the above
+ /* we might have caused the interrupt, but the above
* read cleared it, and just in case the driver is
* down there is nothing to do so return handled
*/
@@ -3802,7 +3793,8 @@ static irqreturn_t e1000_intr(int irq, void *data)
__napi_schedule(&adapter->napi);
} else {
/* this really should not happen! if it does it is basically a
- * bug, but not a hard error, so enable ints and continue */
+ * bug, but not a hard error, so enable ints and continue
+ */
if (!test_bit(__E1000_DOWN, &adapter->flags))
e1000_irq_enable(adapter);
}
@@ -3816,7 +3808,8 @@ static irqreturn_t e1000_intr(int irq, void *data)
**/
static int e1000_clean(struct napi_struct *napi, int budget)
{
- struct e1000_adapter *adapter = container_of(napi, struct e1000_adapter, napi);
+ struct e1000_adapter *adapter = container_of(napi, struct e1000_adapter,
+ napi);
int tx_clean_complete = 0, work_done = 0;
tx_clean_complete = e1000_clean_tx_irq(adapter, &adapter->tx_ring[0]);
@@ -3907,11 +3900,12 @@ static bool e1000_clean_tx_irq(struct e1000_adapter *adapter,
if (adapter->detect_tx_hung) {
/* Detect a transmit hang in hardware, this serializes the
- * check with the clearing of time_stamp and movement of i */
+ * check with the clearing of time_stamp and movement of i
+ */
adapter->detect_tx_hung = false;
if (tx_ring->buffer_info[eop].time_stamp &&
time_after(jiffies, tx_ring->buffer_info[eop].time_stamp +
- (adapter->tx_timeout_factor * HZ)) &&
+ (adapter->tx_timeout_factor * HZ)) &&
!(er32(STATUS) & E1000_STATUS_TXOFF)) {
/* detected Tx unit hang */
@@ -3954,7 +3948,6 @@ static bool e1000_clean_tx_irq(struct e1000_adapter *adapter,
* @csum: receive descriptor csum field
* @sk_buff: socket buffer with received data
**/
-
static void e1000_rx_checksum(struct e1000_adapter *adapter, u32 status_err,
u32 csum, struct sk_buff *skb)
{
@@ -3990,7 +3983,7 @@ static void e1000_rx_checksum(struct e1000_adapter *adapter, u32 status_err,
* e1000_consume_page - helper function
**/
static void e1000_consume_page(struct e1000_buffer *bi, struct sk_buff *skb,
- u16 length)
+ u16 length)
{
bi->page = NULL;
skb->len += length;
@@ -4086,11 +4079,11 @@ static bool e1000_clean_jumbo_rx_irq(struct e1000_adapter *adapter,
if (TBI_ACCEPT(hw, status, rx_desc->errors, length,
last_byte)) {
spin_lock_irqsave(&adapter->stats_lock,
- irq_flags);
+ irq_flags);
e1000_tbi_adjust_stats(hw, &adapter->stats,
length, mapped);
spin_unlock_irqrestore(&adapter->stats_lock,
- irq_flags);
+ irq_flags);
length--;
} else {
if (netdev->features & NETIF_F_RXALL)
@@ -4098,7 +4091,8 @@ static bool e1000_clean_jumbo_rx_irq(struct e1000_adapter *adapter,
/* recycle both page and skb */
buffer_info->skb = skb;
/* an error means any chain goes out the window
- * too */
+ * too
+ */
if (rx_ring->rx_skb_top)
dev_kfree_skb(rx_ring->rx_skb_top);
rx_ring->rx_skb_top = NULL;
@@ -4114,7 +4108,7 @@ process_skb:
/* this is the beginning of a chain */
rxtop = skb;
skb_fill_page_desc(rxtop, 0, buffer_info->page,
- 0, length);
+ 0, length);
} else {
/* this is the middle of a chain */
skb_fill_page_desc(rxtop,
@@ -4132,38 +4126,42 @@ process_skb:
skb_shinfo(rxtop)->nr_frags,
buffer_info->page, 0, length);
/* re-use the current skb, we only consumed the
- * page */
+ * page
+ */
buffer_info->skb = skb;
skb = rxtop;
rxtop = NULL;
e1000_consume_page(buffer_info, skb, length);
} else {
/* no chain, got EOP, this buf is the packet
- * copybreak to save the put_page/alloc_page */
+ * copybreak to save the put_page/alloc_page
+ */
if (length <= copybreak &&
skb_tailroom(skb) >= length) {
u8 *vaddr;
vaddr = kmap_atomic(buffer_info->page);
- memcpy(skb_tail_pointer(skb), vaddr, length);
+ memcpy(skb_tail_pointer(skb), vaddr,
+ length);
kunmap_atomic(vaddr);
/* re-use the page, so don't erase
- * buffer_info->page */
+ * buffer_info->page
+ */
skb_put(skb, length);
} else {
skb_fill_page_desc(skb, 0,
- buffer_info->page, 0,
- length);
+ buffer_info->page, 0,
+ length);
e1000_consume_page(buffer_info, skb,
- length);
+ length);
}
}
}
/* Receive Checksum Offload XXX recompute due to CRC strip? */
e1000_rx_checksum(adapter,
- (u32)(status) |
- ((u32)(rx_desc->errors) << 24),
- le16_to_cpu(rx_desc->csum), skb);
+ (u32)(status) |
+ ((u32)(rx_desc->errors) << 24),
+ le16_to_cpu(rx_desc->csum), skb);
total_rx_bytes += (skb->len - 4); /* don't count FCS */
if (likely(!(netdev->features & NETIF_F_RXFCS)))
@@ -4205,8 +4203,7 @@ next_desc:
return cleaned;
}
-/*
- * this should improve performance for small packets with large amounts
+/* this should improve performance for small packets with large amounts
* of reassembly being done in the stack
*/
static void e1000_check_copybreak(struct net_device *netdev,
@@ -4310,9 +4307,9 @@ static bool e1000_clean_rx_irq(struct e1000_adapter *adapter,
last_byte)) {
spin_lock_irqsave(&adapter->stats_lock, flags);
e1000_tbi_adjust_stats(hw, &adapter->stats,
- length, skb->data);
+ length, skb->data);
spin_unlock_irqrestore(&adapter->stats_lock,
- flags);
+ flags);
length--;
} else {
if (netdev->features & NETIF_F_RXALL)
@@ -4377,10 +4374,9 @@ next_desc:
* @rx_ring: pointer to receive ring structure
* @cleaned_count: number of buffers to allocate this pass
**/
-
static void
e1000_alloc_jumbo_rx_buffers(struct e1000_adapter *adapter,
- struct e1000_rx_ring *rx_ring, int cleaned_count)
+ struct e1000_rx_ring *rx_ring, int cleaned_count)
{
struct net_device *netdev = adapter->netdev;
struct pci_dev *pdev = adapter->pdev;
@@ -4421,7 +4417,7 @@ check_page:
if (!buffer_info->dma) {
buffer_info->dma = dma_map_page(&pdev->dev,
- buffer_info->page, 0,
+ buffer_info->page, 0,
buffer_info->length,
DMA_FROM_DEVICE);
if (dma_mapping_error(&pdev->dev, buffer_info->dma)) {
@@ -4451,7 +4447,8 @@ check_page:
/* Force memory writes to complete before letting h/w
* know there are new descriptors to fetch. (Only
* applicable for weak-ordered memory model archs,
- * such as IA-64). */
+ * such as IA-64).
+ */
wmb();
writel(i, adapter->hw.hw_addr + rx_ring->rdt);
}
@@ -4461,7 +4458,6 @@ check_page:
* e1000_alloc_rx_buffers - Replace used receive buffers; legacy & extended
* @adapter: address of board private structure
**/
-
static void e1000_alloc_rx_buffers(struct e1000_adapter *adapter,
struct e1000_rx_ring *rx_ring,
int cleaned_count)
@@ -4532,8 +4528,7 @@ map_skb:
break; /* while !buffer_info->skb */
}
- /*
- * XXX if it was allocated cleanly it will never map to a
+ /* XXX if it was allocated cleanly it will never map to a
* boundary crossing
*/
@@ -4571,7 +4566,8 @@ map_skb:
/* Force memory writes to complete before letting h/w
* know there are new descriptors to fetch. (Only
* applicable for weak-ordered memory model archs,
- * such as IA-64). */
+ * such as IA-64).
+ */
wmb();
writel(i, hw->hw_addr + rx_ring->rdt);
}
@@ -4581,7 +4577,6 @@ map_skb:
* e1000_smartspeed - Workaround for SmartSpeed on 82541 and 82547 controllers.
* @adapter:
**/
-
static void e1000_smartspeed(struct e1000_adapter *adapter)
{
struct e1000_hw *hw = &adapter->hw;
@@ -4594,7 +4589,8 @@ static void e1000_smartspeed(struct e1000_adapter *adapter)
if (adapter->smartspeed == 0) {
/* If Master/Slave config fault is asserted twice,
- * we assume back-to-back */
+ * we assume back-to-back
+ */
e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_status);
if (!(phy_status & SR_1000T_MS_CONFIG_FAULT)) return;
e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_status);
@@ -4607,7 +4603,7 @@ static void e1000_smartspeed(struct e1000_adapter *adapter)
adapter->smartspeed++;
if (!e1000_phy_setup_autoneg(hw) &&
!e1000_read_phy_reg(hw, PHY_CTRL,
- &phy_ctrl)) {
+ &phy_ctrl)) {
phy_ctrl |= (MII_CR_AUTO_NEG_EN |
MII_CR_RESTART_AUTO_NEG);
e1000_write_phy_reg(hw, PHY_CTRL,
@@ -4638,7 +4634,6 @@ static void e1000_smartspeed(struct e1000_adapter *adapter)
* @ifreq:
* @cmd:
**/
-
static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
{
switch (cmd) {
@@ -4657,7 +4652,6 @@ static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
* @ifreq:
* @cmd:
**/
-
static int e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr,
int cmd)
{
@@ -4919,7 +4913,8 @@ int e1000_set_spd_dplx(struct e1000_adapter *adapter, u32 spd, u8 dplx)
hw->autoneg = 0;
/* Make sure dplx is at most 1 bit and lsb of speed is not set
- * for the switch() below to work */
+ * for the switch() below to work
+ */
if ((spd & 1) || (dplx & ~1))
goto err_inval;
@@ -5122,8 +5117,7 @@ static void e1000_shutdown(struct pci_dev *pdev)
}
#ifdef CONFIG_NET_POLL_CONTROLLER
-/*
- * Polling 'interrupt' - used by things like netconsole to send skbs
+/* Polling 'interrupt' - used by things like netconsole to send skbs
* without having to re-enable interrupts. It's not called while
* the interrupt routine is executing.
*/
diff --git a/drivers/net/ethernet/intel/e1000/e1000_param.c b/drivers/net/ethernet/intel/e1000/e1000_param.c
index 750fc0194f37..c9cde352b1c8 100644
--- a/drivers/net/ethernet/intel/e1000/e1000_param.c
+++ b/drivers/net/ethernet/intel/e1000/e1000_param.c
@@ -267,7 +267,6 @@ static void e1000_check_copper_options(struct e1000_adapter *adapter);
* value exists, a default value is used. The final value is stored
* in a variable in the adapter structure.
**/
-
void e1000_check_options(struct e1000_adapter *adapter)
{
struct e1000_option opt;
@@ -319,7 +318,8 @@ void e1000_check_options(struct e1000_adapter *adapter)
.def = E1000_DEFAULT_RXD,
.arg = { .r = {
.min = E1000_MIN_RXD,
- .max = mac_type < e1000_82544 ? E1000_MAX_RXD : E1000_MAX_82544_RXD
+ .max = mac_type < e1000_82544 ? E1000_MAX_RXD :
+ E1000_MAX_82544_RXD
}}
};
@@ -408,7 +408,7 @@ void e1000_check_options(struct e1000_adapter *adapter)
if (num_TxAbsIntDelay > bd) {
adapter->tx_abs_int_delay = TxAbsIntDelay[bd];
e1000_validate_option(&adapter->tx_abs_int_delay, &opt,
- adapter);
+ adapter);
} else {
adapter->tx_abs_int_delay = opt.def;
}
@@ -426,7 +426,7 @@ void e1000_check_options(struct e1000_adapter *adapter)
if (num_RxIntDelay > bd) {
adapter->rx_int_delay = RxIntDelay[bd];
e1000_validate_option(&adapter->rx_int_delay, &opt,
- adapter);
+ adapter);
} else {
adapter->rx_int_delay = opt.def;
}
@@ -444,7 +444,7 @@ void e1000_check_options(struct e1000_adapter *adapter)
if (num_RxAbsIntDelay > bd) {
adapter->rx_abs_int_delay = RxAbsIntDelay[bd];
e1000_validate_option(&adapter->rx_abs_int_delay, &opt,
- adapter);
+ adapter);
} else {
adapter->rx_abs_int_delay = opt.def;
}
@@ -479,16 +479,17 @@ void e1000_check_options(struct e1000_adapter *adapter)
break;
case 4:
e_dev_info("%s set to simplified "
- "(2000-8000) ints mode\n", opt.name);
+ "(2000-8000) ints mode\n", opt.name);
adapter->itr_setting = adapter->itr;
break;
default:
e1000_validate_option(&adapter->itr, &opt,
- adapter);
+ adapter);
/* save the setting, because the dynamic bits
* change itr.
* clear the lower two bits because they are
- * used as control */
+ * used as control
+ */
adapter->itr_setting = adapter->itr & ~3;
break;
}
@@ -533,7 +534,6 @@ void e1000_check_options(struct e1000_adapter *adapter)
*
* Handles speed and duplex options on fiber adapters
**/
-
static void e1000_check_fiber_options(struct e1000_adapter *adapter)
{
int bd = adapter->bd_number;
@@ -559,7 +559,6 @@ static void e1000_check_fiber_options(struct e1000_adapter *adapter)
*
* Handles speed and duplex options on copper adapters
**/
-
static void e1000_check_copper_options(struct e1000_adapter *adapter)
{
struct e1000_option opt;
@@ -681,22 +680,22 @@ static void e1000_check_copper_options(struct e1000_adapter *adapter)
e_dev_info("Using Autonegotiation at Half Duplex only\n");
adapter->hw.autoneg = adapter->fc_autoneg = 1;
adapter->hw.autoneg_advertised = ADVERTISE_10_HALF |
- ADVERTISE_100_HALF;
+ ADVERTISE_100_HALF;
break;
case FULL_DUPLEX:
e_dev_info("Full Duplex specified without Speed\n");
e_dev_info("Using Autonegotiation at Full Duplex only\n");
adapter->hw.autoneg = adapter->fc_autoneg = 1;
adapter->hw.autoneg_advertised = ADVERTISE_10_FULL |
- ADVERTISE_100_FULL |
- ADVERTISE_1000_FULL;
+ ADVERTISE_100_FULL |
+ ADVERTISE_1000_FULL;
break;
case SPEED_10:
e_dev_info("10 Mbps Speed specified without Duplex\n");
e_dev_info("Using Autonegotiation at 10 Mbps only\n");
adapter->hw.autoneg = adapter->fc_autoneg = 1;
adapter->hw.autoneg_advertised = ADVERTISE_10_HALF |
- ADVERTISE_10_FULL;
+ ADVERTISE_10_FULL;
break;
case SPEED_10 + HALF_DUPLEX:
e_dev_info("Forcing to 10 Mbps Half Duplex\n");
@@ -715,7 +714,7 @@ static void e1000_check_copper_options(struct e1000_adapter *adapter)
e_dev_info("Using Autonegotiation at 100 Mbps only\n");
adapter->hw.autoneg = adapter->fc_autoneg = 1;
adapter->hw.autoneg_advertised = ADVERTISE_100_HALF |
- ADVERTISE_100_FULL;
+ ADVERTISE_100_FULL;
break;
case SPEED_100 + HALF_DUPLEX:
e_dev_info("Forcing to 100 Mbps Half Duplex\n");
diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
index 3f7dbd1cdb0f..a177b8b65c44 100644
--- a/drivers/net/ethernet/intel/e1000e/netdev.c
+++ b/drivers/net/ethernet/intel/e1000e/netdev.c
@@ -4830,6 +4830,13 @@ static void e1000_watchdog_task(struct work_struct *work)
&adapter->link_speed,
&adapter->link_duplex);
e1000_print_link_info(adapter);
+
+ /* check if SmartSpeed worked */
+ e1000e_check_downshift(hw);
+ if (phy->speed_downgraded)
+ netdev_warn(netdev,
+ "Link Speed was downgraded by SmartSpeed\n");
+
/* On supported PHYs, check for duplex mismatch only
* if link has autonegotiated at 10/100 half
*/
diff --git a/drivers/net/ethernet/intel/igb/igb_ethtool.c b/drivers/net/ethernet/intel/igb/igb_ethtool.c
index 40b5d568d808..a3830a8ba4c1 100644
--- a/drivers/net/ethernet/intel/igb/igb_ethtool.c
+++ b/drivers/net/ethernet/intel/igb/igb_ethtool.c
@@ -1891,7 +1891,7 @@ static int igb_link_test(struct igb_adapter *adapter, u64 *data)
} else {
hw->mac.ops.check_for_link(&adapter->hw);
if (hw->mac.autoneg)
- msleep(4000);
+ msleep(5000);
if (!(rd32(E1000_STATUS) & E1000_STATUS_LU))
*data = 1;
diff --git a/drivers/net/ethernet/intel/igbvf/igbvf.h b/drivers/net/ethernet/intel/igbvf/igbvf.h
index fdca7b672776..a1463e3d14c0 100644
--- a/drivers/net/ethernet/intel/igbvf/igbvf.h
+++ b/drivers/net/ethernet/intel/igbvf/igbvf.h
@@ -127,8 +127,8 @@ struct igbvf_buffer {
/* Tx */
struct {
unsigned long time_stamp;
+ union e1000_adv_tx_desc *next_to_watch;
u16 length;
- u16 next_to_watch;
u16 mapped_as_page;
};
/* Rx */
diff --git a/drivers/net/ethernet/intel/igbvf/netdev.c b/drivers/net/ethernet/intel/igbvf/netdev.c
index f53f7136e508..d60cd4393415 100644
--- a/drivers/net/ethernet/intel/igbvf/netdev.c
+++ b/drivers/net/ethernet/intel/igbvf/netdev.c
@@ -797,20 +797,31 @@ static bool igbvf_clean_tx_irq(struct igbvf_ring *tx_ring)
struct sk_buff *skb;
union e1000_adv_tx_desc *tx_desc, *eop_desc;
unsigned int total_bytes = 0, total_packets = 0;
- unsigned int i, eop, count = 0;
+ unsigned int i, count = 0;
bool cleaned = false;
i = tx_ring->next_to_clean;
- eop = tx_ring->buffer_info[i].next_to_watch;
- eop_desc = IGBVF_TX_DESC_ADV(*tx_ring, eop);
+ buffer_info = &tx_ring->buffer_info[i];
+ eop_desc = buffer_info->next_to_watch;
+
+ do {
+ /* if next_to_watch is not set then there is no work pending */
+ if (!eop_desc)
+ break;
+
+ /* prevent any other reads prior to eop_desc */
+ read_barrier_depends();
+
+ /* if DD is not set pending work has not been completed */
+ if (!(eop_desc->wb.status & cpu_to_le32(E1000_TXD_STAT_DD)))
+ break;
+
+ /* clear next_to_watch to prevent false hangs */
+ buffer_info->next_to_watch = NULL;
- while ((eop_desc->wb.status & cpu_to_le32(E1000_TXD_STAT_DD)) &&
- (count < tx_ring->count)) {
- rmb(); /* read buffer_info after eop_desc status */
for (cleaned = false; !cleaned; count++) {
tx_desc = IGBVF_TX_DESC_ADV(*tx_ring, i);
- buffer_info = &tx_ring->buffer_info[i];
- cleaned = (i == eop);
+ cleaned = (tx_desc == eop_desc);
skb = buffer_info->skb;
if (skb) {
@@ -831,10 +842,12 @@ static bool igbvf_clean_tx_irq(struct igbvf_ring *tx_ring)
i++;
if (i == tx_ring->count)
i = 0;
+
+ buffer_info = &tx_ring->buffer_info[i];
}
- eop = tx_ring->buffer_info[i].next_to_watch;
- eop_desc = IGBVF_TX_DESC_ADV(*tx_ring, eop);
- }
+
+ eop_desc = buffer_info->next_to_watch;
+ } while (count < tx_ring->count);
tx_ring->next_to_clean = i;
@@ -1961,7 +1974,6 @@ static int igbvf_tso(struct igbvf_adapter *adapter,
context_desc->seqnum_seed = 0;
buffer_info->time_stamp = jiffies;
- buffer_info->next_to_watch = i;
buffer_info->dma = 0;
i++;
if (i == tx_ring->count)
@@ -2021,7 +2033,6 @@ static inline bool igbvf_tx_csum(struct igbvf_adapter *adapter,
context_desc->mss_l4len_idx = 0;
buffer_info->time_stamp = jiffies;
- buffer_info->next_to_watch = i;
buffer_info->dma = 0;
i++;
if (i == tx_ring->count)
@@ -2061,8 +2072,7 @@ static int igbvf_maybe_stop_tx(struct net_device *netdev, int size)
static inline int igbvf_tx_map_adv(struct igbvf_adapter *adapter,
struct igbvf_ring *tx_ring,
- struct sk_buff *skb,
- unsigned int first)
+ struct sk_buff *skb)
{
struct igbvf_buffer *buffer_info;
struct pci_dev *pdev = adapter->pdev;
@@ -2077,7 +2087,6 @@ static inline int igbvf_tx_map_adv(struct igbvf_adapter *adapter,
buffer_info->length = len;
/* set time_stamp *before* dma to help avoid a possible race */
buffer_info->time_stamp = jiffies;
- buffer_info->next_to_watch = i;
buffer_info->mapped_as_page = false;
buffer_info->dma = dma_map_single(&pdev->dev, skb->data, len,
DMA_TO_DEVICE);
@@ -2100,7 +2109,6 @@ static inline int igbvf_tx_map_adv(struct igbvf_adapter *adapter,
BUG_ON(len >= IGBVF_MAX_DATA_PER_TXD);
buffer_info->length = len;
buffer_info->time_stamp = jiffies;
- buffer_info->next_to_watch = i;
buffer_info->mapped_as_page = true;
buffer_info->dma = skb_frag_dma_map(&pdev->dev, frag, 0, len,
DMA_TO_DEVICE);
@@ -2109,7 +2117,6 @@ static inline int igbvf_tx_map_adv(struct igbvf_adapter *adapter,
}
tx_ring->buffer_info[i].skb = skb;
- tx_ring->buffer_info[first].next_to_watch = i;
return ++count;
@@ -2120,7 +2127,6 @@ dma_error:
buffer_info->dma = 0;
buffer_info->time_stamp = 0;
buffer_info->length = 0;
- buffer_info->next_to_watch = 0;
buffer_info->mapped_as_page = false;
if (count)
count--;
@@ -2139,7 +2145,8 @@ dma_error:
static inline void igbvf_tx_queue_adv(struct igbvf_adapter *adapter,
struct igbvf_ring *tx_ring,
- int tx_flags, int count, u32 paylen,
+ int tx_flags, int count,
+ unsigned int first, u32 paylen,
u8 hdr_len)
{
union e1000_adv_tx_desc *tx_desc = NULL;
@@ -2189,6 +2196,7 @@ static inline void igbvf_tx_queue_adv(struct igbvf_adapter *adapter,
* such as IA-64). */
wmb();
+ tx_ring->buffer_info[first].next_to_watch = tx_desc;
tx_ring->next_to_use = i;
writel(i, adapter->hw.hw_addr + tx_ring->tail);
/* we need this if more than one processor can write to our tail
@@ -2255,11 +2263,11 @@ static netdev_tx_t igbvf_xmit_frame_ring_adv(struct sk_buff *skb,
* count reflects descriptors mapped, if 0 then mapping error
* has occurred and we need to rewind the descriptor queue
*/
- count = igbvf_tx_map_adv(adapter, tx_ring, skb, first);
+ count = igbvf_tx_map_adv(adapter, tx_ring, skb);
if (count) {
igbvf_tx_queue_adv(adapter, tx_ring, tx_flags, count,
- skb->len, hdr_len);
+ first, skb->len, hdr_len);
/* Make sure there is space in the ring for the next send. */
igbvf_maybe_stop_tx(netdev, MAX_SKB_FRAGS + 4);
} else {
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe.h b/drivers/net/ethernet/intel/ixgbe/ixgbe.h
index d268c7b222c7..a8e10cff7a89 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe.h
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe.h
@@ -156,7 +156,7 @@ struct vf_macvlans {
/* Tx Descriptors needed, worst case */
#define TXD_USE_COUNT(S) DIV_ROUND_UP((S), IXGBE_MAX_DATA_PER_TXD)
-#define DESC_NEEDED ((MAX_SKB_FRAGS * TXD_USE_COUNT(PAGE_SIZE)) + 4)
+#define DESC_NEEDED (MAX_SKB_FRAGS + 4)
/* wrapper around a pointer to a socket buffer,
* so a DMA handle can be stored along with the buffer */
@@ -201,6 +201,7 @@ struct ixgbe_rx_queue_stats {
enum ixgbe_ring_state_t {
__IXGBE_TX_FDIR_INIT_DONE,
+ __IXGBE_TX_XPS_INIT_DONE,
__IXGBE_TX_DETECT_HANG,
__IXGBE_HANG_CHECK_ARMED,
__IXGBE_RX_RSC_ENABLED,
@@ -278,15 +279,10 @@ enum ixgbe_ring_f_enum {
#define IXGBE_MAX_RSS_INDICES 16
#define IXGBE_MAX_VMDQ_INDICES 64
-#define IXGBE_MAX_FDIR_INDICES 64
-#ifdef IXGBE_FCOE
+#define IXGBE_MAX_FDIR_INDICES 63 /* based on q_vector limit */
#define IXGBE_MAX_FCOE_INDICES 8
-#define MAX_RX_QUEUES (IXGBE_MAX_FDIR_INDICES + IXGBE_MAX_FCOE_INDICES)
-#define MAX_TX_QUEUES (IXGBE_MAX_FDIR_INDICES + IXGBE_MAX_FCOE_INDICES)
-#else
-#define MAX_RX_QUEUES IXGBE_MAX_FDIR_INDICES
-#define MAX_TX_QUEUES IXGBE_MAX_FDIR_INDICES
-#endif /* IXGBE_FCOE */
+#define MAX_RX_QUEUES (IXGBE_MAX_FDIR_INDICES + 1)
+#define MAX_TX_QUEUES (IXGBE_MAX_FDIR_INDICES + 1)
struct ixgbe_ring_feature {
u16 limit; /* upper limit on feature indices */
u16 indices; /* current value of indices */
@@ -624,6 +620,7 @@ enum ixgbe_state_t {
__IXGBE_DOWN,
__IXGBE_SERVICE_SCHED,
__IXGBE_IN_SFP_INIT,
+ __IXGBE_READ_I2C,
};
struct ixgbe_cb {
@@ -704,8 +701,8 @@ extern bool ixgbe_verify_lesm_fw_enabled_82599(struct ixgbe_hw *hw);
extern void ixgbe_set_rx_mode(struct net_device *netdev);
#ifdef CONFIG_IXGBE_DCB
extern void ixgbe_set_rx_drop_en(struct ixgbe_adapter *adapter);
-extern int ixgbe_setup_tc(struct net_device *dev, u8 tc);
#endif
+extern int ixgbe_setup_tc(struct net_device *dev, u8 tc);
extern void ixgbe_tx_ctxtdesc(struct ixgbe_ring *, u32, u32, u32, u32);
extern void ixgbe_do_reset(struct net_device *netdev);
#ifdef CONFIG_IXGBE_HWMON
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
index db6735931d66..f4d2e9e3c6d5 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c
@@ -39,6 +39,7 @@
#include <linux/uaccess.h>
#include "ixgbe.h"
+#include "ixgbe_phy.h"
#define IXGBE_ALL_RAR_ENTRIES 16
@@ -2112,13 +2113,17 @@ static int ixgbe_set_coalesce(struct net_device *netdev,
struct ixgbe_adapter *adapter = netdev_priv(netdev);
struct ixgbe_q_vector *q_vector;
int i;
- u16 tx_itr_param, rx_itr_param;
+ u16 tx_itr_param, rx_itr_param, tx_itr_prev;
bool need_reset = false;
- /* don't accept tx specific changes if we've got mixed RxTx vectors */
- if (adapter->q_vector[0]->tx.count && adapter->q_vector[0]->rx.count
- && ec->tx_coalesce_usecs)
- return -EINVAL;
+ if (adapter->q_vector[0]->tx.count && adapter->q_vector[0]->rx.count) {
+ /* reject Tx specific changes in case of mixed RxTx vectors */
+ if (ec->tx_coalesce_usecs)
+ return -EINVAL;
+ tx_itr_prev = adapter->rx_itr_setting;
+ } else {
+ tx_itr_prev = adapter->tx_itr_setting;
+ }
if ((ec->rx_coalesce_usecs > (IXGBE_MAX_EITR >> 2)) ||
(ec->tx_coalesce_usecs > (IXGBE_MAX_EITR >> 2)))
@@ -2144,8 +2149,25 @@ static int ixgbe_set_coalesce(struct net_device *netdev,
else
tx_itr_param = adapter->tx_itr_setting;
+ /* mixed Rx/Tx */
+ if (adapter->q_vector[0]->tx.count && adapter->q_vector[0]->rx.count)
+ adapter->tx_itr_setting = adapter->rx_itr_setting;
+
+#if IS_ENABLED(CONFIG_BQL)
+ /* detect ITR changes that require update of TXDCTL.WTHRESH */
+ if ((adapter->tx_itr_setting > 1) &&
+ (adapter->tx_itr_setting < IXGBE_100K_ITR)) {
+ if ((tx_itr_prev == 1) ||
+ (tx_itr_prev > IXGBE_100K_ITR))
+ need_reset = true;
+ } else {
+ if ((tx_itr_prev > 1) &&
+ (tx_itr_prev < IXGBE_100K_ITR))
+ need_reset = true;
+ }
+#endif
/* check the old value and enable RSC if necessary */
- need_reset = ixgbe_update_rsc(adapter);
+ need_reset |= ixgbe_update_rsc(adapter);
for (i = 0; i < adapter->num_q_vectors; i++) {
q_vector = adapter->q_vector[i];
@@ -2731,6 +2753,225 @@ static int ixgbe_get_ts_info(struct net_device *dev,
return 0;
}
+static unsigned int ixgbe_max_channels(struct ixgbe_adapter *adapter)
+{
+ unsigned int max_combined;
+ u8 tcs = netdev_get_num_tc(adapter->netdev);
+
+ if (!(adapter->flags & IXGBE_FLAG_MSIX_ENABLED)) {
+ /* We only support one q_vector without MSI-X */
+ max_combined = 1;
+ } else if (adapter->flags & IXGBE_FLAG_SRIOV_ENABLED) {
+ /* SR-IOV currently only allows one queue on the PF */
+ max_combined = 1;
+ } else if (tcs > 1) {
+ /* For DCB report channels per traffic class */
+ if (adapter->hw.mac.type == ixgbe_mac_82598EB) {
+ /* 8 TC w/ 4 queues per TC */
+ max_combined = 4;
+ } else if (tcs > 4) {
+ /* 8 TC w/ 8 queues per TC */
+ max_combined = 8;
+ } else {
+ /* 4 TC w/ 16 queues per TC */
+ max_combined = 16;
+ }
+ } else if (adapter->atr_sample_rate) {
+ /* support up to 64 queues with ATR */
+ max_combined = IXGBE_MAX_FDIR_INDICES;
+ } else {
+ /* support up to 16 queues with RSS */
+ max_combined = IXGBE_MAX_RSS_INDICES;
+ }
+
+ return max_combined;
+}
+
+static void ixgbe_get_channels(struct net_device *dev,
+ struct ethtool_channels *ch)
+{
+ struct ixgbe_adapter *adapter = netdev_priv(dev);
+
+ /* report maximum channels */
+ ch->max_combined = ixgbe_max_channels(adapter);
+
+ /* report info for other vector */
+ if (adapter->flags & IXGBE_FLAG_MSIX_ENABLED) {
+ ch->max_other = NON_Q_VECTORS;
+ ch->other_count = NON_Q_VECTORS;
+ }
+
+ /* record RSS queues */
+ ch->combined_count = adapter->ring_feature[RING_F_RSS].indices;
+
+ /* nothing else to report if RSS is disabled */
+ if (ch->combined_count == 1)
+ return;
+
+ /* we do not support ATR queueing if SR-IOV is enabled */
+ if (adapter->flags & IXGBE_FLAG_SRIOV_ENABLED)
+ return;
+
+ /* same thing goes for being DCB enabled */
+ if (netdev_get_num_tc(dev) > 1)
+ return;
+
+ /* if ATR is disabled we can exit */
+ if (!adapter->atr_sample_rate)
+ return;
+
+ /* report flow director queues as maximum channels */
+ ch->combined_count = adapter->ring_feature[RING_F_FDIR].indices;
+}
+
+static int ixgbe_set_channels(struct net_device *dev,
+ struct ethtool_channels *ch)
+{
+ struct ixgbe_adapter *adapter = netdev_priv(dev);
+ unsigned int count = ch->combined_count;
+
+ /* verify they are not requesting separate vectors */
+ if (!count || ch->rx_count || ch->tx_count)
+ return -EINVAL;
+
+ /* verify other_count has not changed */
+ if (ch->other_count != NON_Q_VECTORS)
+ return -EINVAL;
+
+ /* verify the number of channels does not exceed hardware limits */
+ if (count > ixgbe_max_channels(adapter))
+ return -EINVAL;
+
+ /* update feature limits from largest to smallest supported values */
+ adapter->ring_feature[RING_F_FDIR].limit = count;
+
+ /* cap RSS limit at 16 */
+ if (count > IXGBE_MAX_RSS_INDICES)
+ count = IXGBE_MAX_RSS_INDICES;
+ adapter->ring_feature[RING_F_RSS].limit = count;
+
+#ifdef IXGBE_FCOE
+ /* cap FCoE limit at 8 */
+ if (count > IXGBE_FCRETA_SIZE)
+ count = IXGBE_FCRETA_SIZE;
+ adapter->ring_feature[RING_F_FCOE].limit = count;
+
+#endif
+ /* use setup TC to update any traffic class queue mapping */
+ return ixgbe_setup_tc(dev, netdev_get_num_tc(dev));
+}
+
+static int ixgbe_get_module_info(struct net_device *dev,
+ struct ethtool_modinfo *modinfo)
+{
+ struct ixgbe_adapter *adapter = netdev_priv(dev);
+ struct ixgbe_hw *hw = &adapter->hw;
+ u32 status;
+ u8 sff8472_rev, addr_mode;
+ int ret_val = 0;
+ bool page_swap = false;
+
+ /* avoid concurent i2c reads */
+ while (test_bit(__IXGBE_IN_SFP_INIT, &adapter->state))
+ msleep(100);
+
+ /* used by the service task */
+ set_bit(__IXGBE_READ_I2C, &adapter->state);
+
+ /* Check whether we support SFF-8472 or not */
+ status = hw->phy.ops.read_i2c_eeprom(hw,
+ IXGBE_SFF_SFF_8472_COMP,
+ &sff8472_rev);
+ if (status != 0) {
+ ret_val = -EIO;
+ goto err_out;
+ }
+
+ /* addressing mode is not supported */
+ status = hw->phy.ops.read_i2c_eeprom(hw,
+ IXGBE_SFF_SFF_8472_SWAP,
+ &addr_mode);
+ if (status != 0) {
+ ret_val = -EIO;
+ goto err_out;
+ }
+
+ if (addr_mode & IXGBE_SFF_ADDRESSING_MODE) {
+ e_err(drv, "Address change required to access page 0xA2, but not supported. Please report the module type to the driver maintainers.\n");
+ page_swap = true;
+ }
+
+ if (sff8472_rev == IXGBE_SFF_SFF_8472_UNSUP || page_swap) {
+ /* We have a SFP, but it does not support SFF-8472 */
+ modinfo->type = ETH_MODULE_SFF_8079;
+ modinfo->eeprom_len = ETH_MODULE_SFF_8079_LEN;
+ } else {
+ /* We have a SFP which supports a revision of SFF-8472. */
+ modinfo->type = ETH_MODULE_SFF_8472;
+ modinfo->eeprom_len = ETH_MODULE_SFF_8472_LEN;
+ }
+
+err_out:
+ clear_bit(__IXGBE_READ_I2C, &adapter->state);
+ return ret_val;
+}
+
+static int ixgbe_get_module_eeprom(struct net_device *dev,
+ struct ethtool_eeprom *ee,
+ u8 *data)
+{
+ struct ixgbe_adapter *adapter = netdev_priv(dev);
+ struct ixgbe_hw *hw = &adapter->hw;
+ u32 status = IXGBE_ERR_PHY_ADDR_INVALID;
+ u8 databyte = 0xFF;
+ int i = 0;
+ int ret_val = 0;
+
+ /* ixgbe_get_module_info is called before this function in all
+ * cases, so we do not need any checks we already do above,
+ * and can trust ee->len to be a known value.
+ */
+
+ while (test_bit(__IXGBE_IN_SFP_INIT, &adapter->state))
+ msleep(100);
+ set_bit(__IXGBE_READ_I2C, &adapter->state);
+
+ /* Read the first block, SFF-8079 */
+ for (i = 0; i < ETH_MODULE_SFF_8079_LEN; i++) {
+ status = hw->phy.ops.read_i2c_eeprom(hw, i, &databyte);
+ if (status != 0) {
+ /* Error occured while reading module */
+ ret_val = -EIO;
+ goto err_out;
+ }
+ data[i] = databyte;
+ }
+
+ /* If the second block is requested, check if SFF-8472 is supported. */
+ if (ee->len == ETH_MODULE_SFF_8472_LEN) {
+ if (data[IXGBE_SFF_SFF_8472_COMP] == IXGBE_SFF_SFF_8472_UNSUP)
+ return -EOPNOTSUPP;
+
+ /* Read the second block, SFF-8472 */
+ for (i = ETH_MODULE_SFF_8079_LEN;
+ i < ETH_MODULE_SFF_8472_LEN; i++) {
+ status = hw->phy.ops.read_i2c_sff8472(hw,
+ i - ETH_MODULE_SFF_8079_LEN, &databyte);
+ if (status != 0) {
+ /* Error occured while reading module */
+ ret_val = -EIO;
+ goto err_out;
+ }
+ data[i] = databyte;
+ }
+ }
+
+err_out:
+ clear_bit(__IXGBE_READ_I2C, &adapter->state);
+
+ return ret_val;
+}
+
static const struct ethtool_ops ixgbe_ethtool_ops = {
.get_settings = ixgbe_get_settings,
.set_settings = ixgbe_set_settings,
@@ -2759,7 +3000,11 @@ static const struct ethtool_ops ixgbe_ethtool_ops = {
.set_coalesce = ixgbe_set_coalesce,
.get_rxnfc = ixgbe_get_rxnfc,
.set_rxnfc = ixgbe_set_rxnfc,
+ .get_channels = ixgbe_get_channels,
+ .set_channels = ixgbe_set_channels,
.get_ts_info = ixgbe_get_ts_info,
+ .get_module_info = ixgbe_get_module_info,
+ .get_module_eeprom = ixgbe_get_module_eeprom,
};
void ixgbe_set_ethtool_ops(struct net_device *netdev)
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c
index 9ffa3309e54d..ef5f7a678ce1 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_lib.c
@@ -386,7 +386,6 @@ static bool ixgbe_set_dcb_sriov_queues(struct ixgbe_adapter *adapter)
fcoe = &adapter->ring_feature[RING_F_FCOE];
/* limit ourselves based on feature limits */
- fcoe_i = min_t(u16, fcoe_i, num_online_cpus());
fcoe_i = min_t(u16, fcoe_i, fcoe->limit);
if (fcoe_i) {
@@ -562,9 +561,6 @@ static bool ixgbe_set_sriov_queues(struct ixgbe_adapter *adapter)
fcoe_i = min_t(u16, fcoe_i, fcoe->limit);
if (vmdq_i > 1 && fcoe_i) {
- /* reserve no more than number of CPUs */
- fcoe_i = min_t(u16, fcoe_i, num_online_cpus());
-
/* alloc queues for FCoE separately */
fcoe->indices = fcoe_i;
fcoe->offset = vmdq_i * rss_i;
@@ -623,8 +619,7 @@ static bool ixgbe_set_rss_queues(struct ixgbe_adapter *adapter)
if (rss_i > 1 && adapter->atr_sample_rate) {
f = &adapter->ring_feature[RING_F_FDIR];
- f->indices = min_t(u16, num_online_cpus(), f->limit);
- rss_i = max_t(u16, rss_i, f->indices);
+ rss_i = f->indices = f->limit;
if (!(adapter->flags & IXGBE_FLAG_FDIR_PERFECT_CAPABLE))
adapter->flags |= IXGBE_FLAG_FDIR_HASH_CAPABLE;
@@ -776,19 +771,23 @@ static int ixgbe_alloc_q_vector(struct ixgbe_adapter *adapter,
{
struct ixgbe_q_vector *q_vector;
struct ixgbe_ring *ring;
- int node = -1;
+ int node = NUMA_NO_NODE;
int cpu = -1;
int ring_count, size;
+ u8 tcs = netdev_get_num_tc(adapter->netdev);
ring_count = txr_count + rxr_count;
size = sizeof(struct ixgbe_q_vector) +
(sizeof(struct ixgbe_ring) * ring_count);
/* customize cpu for Flow Director mapping */
- if (adapter->flags & IXGBE_FLAG_FDIR_HASH_CAPABLE) {
- if (cpu_online(v_idx)) {
- cpu = v_idx;
- node = cpu_to_node(cpu);
+ if ((tcs <= 1) && !(adapter->flags & IXGBE_FLAG_SRIOV_ENABLED)) {
+ u16 rss_i = adapter->ring_feature[RING_F_RSS].indices;
+ if (rss_i > 1 && adapter->atr_sample_rate) {
+ if (cpu_online(v_idx)) {
+ cpu = v_idx;
+ node = cpu_to_node(cpu);
+ }
}
}
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
index 1d5e093e988a..68478d6dfa2d 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c
@@ -2786,13 +2786,19 @@ void ixgbe_configure_tx_ring(struct ixgbe_adapter *adapter,
/*
* set WTHRESH to encourage burst writeback, it should not be set
- * higher than 1 when ITR is 0 as it could cause false TX hangs
+ * higher than 1 when:
+ * - ITR is 0 as it could cause false TX hangs
+ * - ITR is set to > 100k int/sec and BQL is enabled
*
* In order to avoid issues WTHRESH + PTHRESH should always be equal
* to or less than the number of on chip descriptors, which is
* currently 40.
*/
+#if IS_ENABLED(CONFIG_BQL)
+ if (!ring->q_vector || (ring->q_vector->itr < IXGBE_100K_ITR))
+#else
if (!ring->q_vector || (ring->q_vector->itr < 8))
+#endif
txdctl |= (1 << 16); /* WTHRESH = 1 */
else
txdctl |= (8 << 16); /* WTHRESH = 8 */
@@ -2813,6 +2819,16 @@ void ixgbe_configure_tx_ring(struct ixgbe_adapter *adapter,
ring->atr_sample_rate = 0;
}
+ /* initialize XPS */
+ if (!test_and_set_bit(__IXGBE_TX_XPS_INIT_DONE, &ring->state)) {
+ struct ixgbe_q_vector *q_vector = ring->q_vector;
+
+ if (q_vector)
+ netif_set_xps_queue(adapter->netdev,
+ &q_vector->affinity_mask,
+ ring->queue_index);
+ }
+
clear_bit(__IXGBE_HANG_CHECK_ARMED, &ring->state);
/* enable queue */
@@ -4465,7 +4481,7 @@ static int ixgbe_sw_init(struct ixgbe_adapter *adapter)
{
struct ixgbe_hw *hw = &adapter->hw;
struct pci_dev *pdev = adapter->pdev;
- unsigned int rss;
+ unsigned int rss, fdir;
u32 fwsm;
#ifdef CONFIG_IXGBE_DCB
int j;
@@ -4485,9 +4501,10 @@ static int ixgbe_sw_init(struct ixgbe_adapter *adapter)
adapter->ring_feature[RING_F_RSS].limit = rss;
adapter->flags2 |= IXGBE_FLAG2_RSC_CAPABLE;
adapter->flags2 |= IXGBE_FLAG2_RSC_ENABLED;
- adapter->ring_feature[RING_F_FDIR].limit = IXGBE_MAX_FDIR_INDICES;
adapter->max_q_vectors = MAX_Q_VECTORS_82599;
adapter->atr_sample_rate = 20;
+ fdir = min_t(int, IXGBE_MAX_FDIR_INDICES, num_online_cpus());
+ adapter->ring_feature[RING_F_FDIR].limit = fdir;
adapter->fdir_pballoc = IXGBE_FDIR_PBALLOC_64K;
#ifdef CONFIG_IXGBE_DCA
adapter->flags |= IXGBE_FLAG_DCA_CAPABLE;
@@ -5698,6 +5715,10 @@ static void ixgbe_sfp_detection_subtask(struct ixgbe_adapter *adapter)
!(adapter->flags2 & IXGBE_FLAG2_SFP_NEEDS_RESET))
return;
+ /* concurent i2c reads are not supported */
+ if (test_bit(__IXGBE_READ_I2C, &adapter->state))
+ return;
+
/* someone else is in init, wait until next service event */
if (test_and_set_bit(__IXGBE_IN_SFP_INIT, &adapter->state))
return;
@@ -6363,38 +6384,40 @@ static inline int ixgbe_maybe_stop_tx(struct ixgbe_ring *tx_ring, u16 size)
return __ixgbe_maybe_stop_tx(tx_ring, size);
}
+#ifdef IXGBE_FCOE
static u16 ixgbe_select_queue(struct net_device *dev, struct sk_buff *skb)
{
- struct ixgbe_adapter *adapter = netdev_priv(dev);
- int txq = skb_rx_queue_recorded(skb) ? skb_get_rx_queue(skb) :
- smp_processor_id();
-#ifdef IXGBE_FCOE
- __be16 protocol = vlan_get_protocol(skb);
+ struct ixgbe_adapter *adapter;
+ struct ixgbe_ring_feature *f;
+ int txq;
- if (((protocol == htons(ETH_P_FCOE)) ||
- (protocol == htons(ETH_P_FIP))) &&
- (adapter->flags & IXGBE_FLAG_FCOE_ENABLED)) {
- struct ixgbe_ring_feature *f;
+ /*
+ * only execute the code below if protocol is FCoE
+ * or FIP and we have FCoE enabled on the adapter
+ */
+ switch (vlan_get_protocol(skb)) {
+ case __constant_htons(ETH_P_FCOE):
+ case __constant_htons(ETH_P_FIP):
+ adapter = netdev_priv(dev);
- f = &adapter->ring_feature[RING_F_FCOE];
+ if (adapter->flags & IXGBE_FLAG_FCOE_ENABLED)
+ break;
+ default:
+ return __netdev_pick_tx(dev, skb);
+ }
- while (txq >= f->indices)
- txq -= f->indices;
- txq += adapter->ring_feature[RING_F_FCOE].offset;
+ f = &adapter->ring_feature[RING_F_FCOE];
- return txq;
- }
-#endif
+ txq = skb_rx_queue_recorded(skb) ? skb_get_rx_queue(skb) :
+ smp_processor_id();
- if (adapter->flags & IXGBE_FLAG_FDIR_HASH_CAPABLE) {
- while (unlikely(txq >= dev->real_num_tx_queues))
- txq -= dev->real_num_tx_queues;
- return txq;
- }
+ while (txq >= f->indices)
+ txq -= f->indices;
- return skb_tx_hash(dev, skb);
+ return txq + f->offset;
}
+#endif
netdev_tx_t ixgbe_xmit_frame_ring(struct sk_buff *skb,
struct ixgbe_adapter *adapter,
struct ixgbe_ring *tx_ring)
@@ -6799,6 +6822,7 @@ static void ixgbe_set_prio_tc_map(struct ixgbe_adapter *adapter)
}
}
+#endif /* CONFIG_IXGBE_DCB */
/**
* ixgbe_setup_tc - configure net_device for multiple traffic classes
*
@@ -6824,6 +6848,7 @@ int ixgbe_setup_tc(struct net_device *dev, u8 tc)
ixgbe_close(dev);
ixgbe_clear_interrupt_scheme(adapter);
+#ifdef CONFIG_IXGBE_DCB
if (tc) {
netdev_set_num_tc(dev, tc);
ixgbe_set_prio_tc_map(adapter);
@@ -6846,31 +6871,24 @@ int ixgbe_setup_tc(struct net_device *dev, u8 tc)
adapter->dcb_cfg.pfc_mode_enable = false;
}
- ixgbe_init_interrupt_scheme(adapter);
ixgbe_validate_rtr(adapter, tc);
+
+#endif /* CONFIG_IXGBE_DCB */
+ ixgbe_init_interrupt_scheme(adapter);
+
if (netif_running(dev))
- ixgbe_open(dev);
+ return ixgbe_open(dev);
return 0;
}
-#endif /* CONFIG_IXGBE_DCB */
#ifdef CONFIG_PCI_IOV
void ixgbe_sriov_reinit(struct ixgbe_adapter *adapter)
{
struct net_device *netdev = adapter->netdev;
rtnl_lock();
-#ifdef CONFIG_IXGBE_DCB
ixgbe_setup_tc(netdev, netdev_get_num_tc(netdev));
-#else
- if (netif_running(netdev))
- ixgbe_close(netdev);
- ixgbe_clear_interrupt_scheme(adapter);
- ixgbe_init_interrupt_scheme(adapter);
- if (netif_running(netdev))
- ixgbe_open(netdev);
-#endif
rtnl_unlock();
}
@@ -7118,7 +7136,9 @@ static const struct net_device_ops ixgbe_netdev_ops = {
.ndo_open = ixgbe_open,
.ndo_stop = ixgbe_close,
.ndo_start_xmit = ixgbe_xmit_frame,
+#ifdef IXGBE_FCOE
.ndo_select_queue = ixgbe_select_queue,
+#endif
.ndo_set_rx_mode = ixgbe_set_rx_mode,
.ndo_validate_addr = eth_validate_addr,
.ndo_set_mac_address = ixgbe_set_mac,
@@ -7230,9 +7250,8 @@ static int ixgbe_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
const struct ixgbe_info *ii = ixgbe_info_tbl[ent->driver_data];
static int cards_found;
int i, err, pci_using_dac;
+ unsigned int indices = MAX_TX_QUEUES;
u8 part_str[IXGBE_PBANUM_LENGTH];
- unsigned int indices = num_possible_cpus();
- unsigned int dcb_max = 0;
#ifdef IXGBE_FCOE
u16 device_caps;
#endif
@@ -7281,25 +7300,15 @@ static int ixgbe_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
pci_set_master(pdev);
pci_save_state(pdev);
+ if (ii->mac == ixgbe_mac_82598EB) {
#ifdef CONFIG_IXGBE_DCB
- if (ii->mac == ixgbe_mac_82598EB)
- dcb_max = min_t(unsigned int, indices * MAX_TRAFFIC_CLASS,
- IXGBE_MAX_RSS_INDICES);
- else
- dcb_max = min_t(unsigned int, indices * MAX_TRAFFIC_CLASS,
- IXGBE_MAX_FDIR_INDICES);
+ /* 8 TC w/ 4 queues per TC */
+ indices = 4 * MAX_TRAFFIC_CLASS;
+#else
+ indices = IXGBE_MAX_RSS_INDICES;
#endif
+ }
- if (ii->mac == ixgbe_mac_82598EB)
- indices = min_t(unsigned int, indices, IXGBE_MAX_RSS_INDICES);
- else
- indices = min_t(unsigned int, indices, IXGBE_MAX_FDIR_INDICES);
-
-#ifdef IXGBE_FCOE
- indices += min_t(unsigned int, num_possible_cpus(),
- IXGBE_MAX_FCOE_INDICES);
-#endif
- indices = max_t(unsigned int, dcb_max, indices);
netdev = alloc_etherdev_mq(sizeof(struct ixgbe_adapter), indices);
if (!netdev) {
err = -ENOMEM;
@@ -7454,13 +7463,17 @@ skip_sriov:
#ifdef IXGBE_FCOE
if (adapter->flags & IXGBE_FLAG_FCOE_CAPABLE) {
+ unsigned int fcoe_l;
+
if (hw->mac.ops.get_device_caps) {
hw->mac.ops.get_device_caps(hw, &device_caps);
if (device_caps & IXGBE_DEVICE_CAPS_FCOE_OFFLOADS)
adapter->flags &= ~IXGBE_FLAG_FCOE_CAPABLE;
}
- adapter->ring_feature[RING_F_FCOE].limit = IXGBE_FCRETA_SIZE;
+
+ fcoe_l = min_t(int, IXGBE_FCRETA_SIZE, num_online_cpus());
+ adapter->ring_feature[RING_F_FCOE].limit = fcoe_l;
netdev->features |= NETIF_F_FSO |
NETIF_F_FCOE_CRC;
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
index eb534a071fde..060d2ad2ac96 100644
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
@@ -852,11 +852,9 @@ s32 ixgbe_identify_sfp_module_generic(struct ixgbe_hw *hw)
status = hw->phy.ops.read_i2c_eeprom(hw,
IXGBE_SFF_IDENTIFIER,
- &identifier);
+ &identifier);
- if (status == IXGBE_ERR_SWFW_SYNC ||
- status == IXGBE_ERR_I2C ||
- status == IXGBE_ERR_SFP_NOT_PRESENT)
+ if (status != 0)
goto err_read_i2c_eeprom;
/* LAN ID is needed for sfp_type determination */
@@ -870,26 +868,20 @@ s32 ixgbe_identify_sfp_module_generic(struct ixgbe_hw *hw)
IXGBE_SFF_1GBE_COMP_CODES,
&comp_codes_1g);
- if (status == IXGBE_ERR_SWFW_SYNC ||
- status == IXGBE_ERR_I2C ||
- status == IXGBE_ERR_SFP_NOT_PRESENT)
+ if (status != 0)
goto err_read_i2c_eeprom;
status = hw->phy.ops.read_i2c_eeprom(hw,
IXGBE_SFF_10GBE_COMP_CODES,
&comp_codes_10g);
- if (status == IXGBE_ERR_SWFW_SYNC ||
- status == IXGBE_ERR_I2C ||
- status == IXGBE_ERR_SFP_NOT_PRESENT)
+ if (status != 0)
goto err_read_i2c_eeprom;
status = hw->phy.ops.read_i2c_eeprom(hw,
IXGBE_SFF_CABLE_TECHNOLOGY,
&cable_tech);
- if (status == IXGBE_ERR_SWFW_SYNC ||
- status == IXGBE_ERR_I2C ||
- status == IXGBE_ERR_SFP_NOT_PRESENT)
+ if (status != 0)
goto err_read_i2c_eeprom;
/* ID Module
@@ -984,30 +976,24 @@ s32 ixgbe_identify_sfp_module_generic(struct ixgbe_hw *hw)
if (hw->phy.type != ixgbe_phy_nl) {
hw->phy.id = identifier;
status = hw->phy.ops.read_i2c_eeprom(hw,
- IXGBE_SFF_VENDOR_OUI_BYTE0,
- &oui_bytes[0]);
+ IXGBE_SFF_VENDOR_OUI_BYTE0,
+ &oui_bytes[0]);
- if (status == IXGBE_ERR_SWFW_SYNC ||
- status == IXGBE_ERR_I2C ||
- status == IXGBE_ERR_SFP_NOT_PRESENT)
+ if (status != 0)
goto err_read_i2c_eeprom;
status = hw->phy.ops.read_i2c_eeprom(hw,
IXGBE_SFF_VENDOR_OUI_BYTE1,
&oui_bytes[1]);
- if (status == IXGBE_ERR_SWFW_SYNC ||
- status == IXGBE_ERR_I2C ||
- status == IXGBE_ERR_SFP_NOT_PRESENT)
+ if (status != 0)
goto err_read_i2c_eeprom;
status = hw->phy.ops.read_i2c_eeprom(hw,
IXGBE_SFF_VENDOR_OUI_BYTE2,
&oui_bytes[2]);
- if (status == IXGBE_ERR_SWFW_SYNC ||
- status == IXGBE_ERR_I2C ||
- status == IXGBE_ERR_SFP_NOT_PRESENT)
+ if (status != 0)
goto err_read_i2c_eeprom;
vendor_oui =
@@ -1307,9 +1293,9 @@ s32 ixgbe_read_i2c_byte_generic(struct ixgbe_hw *hw, u8 byte_offset,
break;
fail:
+ ixgbe_i2c_bus_clear(hw);
hw->mac.ops.release_swfw_sync(hw, swfw_mask);
msleep(100);
- ixgbe_i2c_bus_clear(hw);
retry++;
if (retry < max_retry)
hw_dbg(hw, "I2C byte read error - Retrying.\n");
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-15 19:30:28 +0000