Merge branch 'merge' of git://git.secretlab.ca/git/linux-2.6 into merge

3 files changed, 154 insertions, 11 deletions

diff --git a/Documentation/powerpc/dts-bindings/fsl/upm-nand.txt b/Documentation/powerpc/dts-bindings/fsl/upm-nand.txt
index 84a04d5eb8e6..a48b2cadc7f0 100644
--- a/Documentation/powerpc/dts-bindings/fsl/upm-nand.txt
+++ b/Documentation/powerpc/dts-bindings/fsl/upm-nand.txt
@@ -5,9 +5,21 @@ Required properties:
 - reg : should specify localbus chip select and size used for the chip.
 - fsl,upm-addr-offset : UPM pattern offset for the address latch.
 - fsl,upm-cmd-offset : UPM pattern offset for the command latch.
-- gpios : may specify optional GPIO connected to the Ready-Not-Busy pin.
 
-Example:
+Optional properties:
+- fsl,upm-wait-flags : add chip-dependent short delays after running the
+	UPM pattern (0x1), after writing a data byte (0x2) or after
+	writing out a buffer (0x4).
+- fsl,upm-addr-line-cs-offsets : address offsets for multi-chip support.
+	The corresponding address lines are used to select the chip.
+- gpios : may specify optional GPIOs connected to the Ready-Not-Busy pins
+	(R/B#). For multi-chip devices, "n" GPIO definitions are required
+	according to the number of chips.
+- chip-delay : chip dependent delay for transfering data from array to
+	read registers (tR). Required if property "gpios" is not used
+	(R/B# pins not connected).
+
+Examples:
 
 upm@1,0 {
 	compatible = "fsl,upm-nand";
@@ -26,3 +38,26 @@ upm@1,0 {
 		};
 	};
 };
+
+upm@3,0 {
+	#address-cells = <0>;
+	#size-cells = <0>;
+	compatible = "tqc,tqm8548-upm-nand", "fsl,upm-nand";
+	reg = <3 0x0 0x800>;
+	fsl,upm-addr-offset = <0x10>;
+	fsl,upm-cmd-offset = <0x08>;
+	/* Multi-chip NAND device */
+	fsl,upm-addr-line-cs-offsets = <0x0 0x200>;
+	fsl,upm-wait-flags = <0x5>;
+	chip-delay = <25>; // in micro-seconds
+
+	nand@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			    label = "fs";
+			    reg = <0x00000000 0x10000000>;
+		};
+	};
+};
diff --git a/Documentation/powerpc/dts-bindings/gpio/led.txt b/Documentation/powerpc/dts-bindings/gpio/led.txt
index ff51f4c0fa9d..4fe14deedc0a 100644
--- a/Documentation/powerpc/dts-bindings/gpio/led.txt
+++ b/Documentation/powerpc/dts-bindings/gpio/led.txt
@@ -1,15 +1,43 @@
-LED connected to GPIO
+LEDs connected to GPIO lines
 
 Required properties:
-- compatible : should be "gpio-led".
-- label : (optional) the label for this LED. If omitted, the label is
+- compatible : should be "gpio-leds".
+
+Each LED is represented as a sub-node of the gpio-leds device.  Each
+node's name represents the name of the corresponding LED.
+
+LED sub-node properties:
+- gpios :  Should specify the LED's GPIO, see "Specifying GPIO information
+  for devices" in Documentation/powerpc/booting-without-of.txt.  Active
+  low LEDs should be indicated using flags in the GPIO specifier.
+- label :  (optional) The label for this LED.  If omitted, the label is
   taken from the node name (excluding the unit address).
-- gpios : should specify LED GPIO.
+- linux,default-trigger :  (optional) This parameter, if present, is a
+  string defining the trigger assigned to the LED.  Current triggers are:
+    "backlight" - LED will act as a back-light, controlled by the framebuffer
+		  system
+    "default-on" - LED will turn on
+    "heartbeat" - LED "double" flashes at a load average based rate
+    "ide-disk" - LED indicates disk activity
+    "timer" - LED flashes at a fixed, configurable rate
 
-Example:
+Examples:
 
-led@0 {
-	compatible = "gpio-led";
-	label = "hdd";
-	gpios = <&mcu_pio 0 1>;
+leds {
+	compatible = "gpio-leds";
+	hdd {
+		label = "IDE Activity";
+		gpios = <&mcu_pio 0 1>; /* Active low */
+		linux,default-trigger = "ide-disk";
+	};
 };
+
+run-control {
+	compatible = "gpio-leds";
+	red {
+		gpios = <&mpc8572 6 0>;
+	};
+	green {
+		gpios = <&mpc8572 7 0>;
+	};
+}
diff --git a/Documentation/powerpc/dts-bindings/mtd-physmap.txt b/Documentation/powerpc/dts-bindings/mtd-physmap.txt
new file mode 100644
index 000000000000..667c9bde8699
--- /dev/null
+++ b/Documentation/powerpc/dts-bindings/mtd-physmap.txt
@@ -0,0 +1,80 @@
+CFI or JEDEC memory-mapped NOR flash
+
+Flash chips (Memory Technology Devices) are often used for solid state
+file systems on embedded devices.
+
+ - compatible : should contain the specific model of flash chip(s)
+   used, if known, followed by either "cfi-flash" or "jedec-flash"
+ - reg : Address range(s) of the flash chip(s)
+   It's possible to (optionally) define multiple "reg" tuples so that
+   non-identical NOR chips can be described in one flash node.
+ - bank-width : Width (in bytes) of the flash bank.  Equal to the
+   device width times the number of interleaved chips.
+ - device-width : (optional) Width of a single flash chip.  If
+   omitted, assumed to be equal to 'bank-width'.
+ - #address-cells, #size-cells : Must be present if the flash has
+   sub-nodes representing partitions (see below).  In this case
+   both #address-cells and #size-cells must be equal to 1.
+
+For JEDEC compatible devices, the following additional properties
+are defined:
+
+ - vendor-id : Contains the flash chip's vendor id (1 byte).
+ - device-id : Contains the flash chip's device id (1 byte).
+
+In addition to the information on the flash bank itself, the
+device tree may optionally contain additional information
+describing partitions of the flash address space.  This can be
+used on platforms which have strong conventions about which
+portions of the flash are used for what purposes, but which don't
+use an on-flash partition table such as RedBoot.
+
+Each partition is represented as a sub-node of the flash device.
+Each node's name represents the name of the corresponding
+partition of the flash device.
+
+Flash partitions
+ - reg : The partition's offset and size within the flash bank.
+ - label : (optional) The label / name for this flash partition.
+   If omitted, the label is taken from the node name (excluding
+   the unit address).
+ - read-only : (optional) This parameter, if present, is a hint to
+   Linux that this flash partition should only be mounted
+   read-only.  This is usually used for flash partitions
+   containing early-boot firmware images or data which should not
+   be clobbered.
+
+Example:
+
+	flash@ff000000 {
+		compatible = "amd,am29lv128ml", "cfi-flash";
+		reg = <ff000000 01000000>;
+		bank-width = <4>;
+		device-width = <1>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		fs@0 {
+			label = "fs";
+			reg = <0 f80000>;
+		};
+		firmware@f80000 {
+			label ="firmware";
+			reg = <f80000 80000>;
+			read-only;
+		};
+	};
+
+Here an example with multiple "reg" tuples:
+
+	flash@f0000000,0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "intel,PC48F4400P0VB", "cfi-flash";
+		reg = <0 0x00000000 0x02000000
+		       0 0x02000000 0x02000000>;
+		bank-width = <2>;
+		partition@0 {
+			label = "test-part1";
+			reg = <0 0x04000000>;
+		};
+	};