Merge tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull gpio updates from Linus Walleij:
 "This is the big bulk of GPIO changes queued for the v4.2 kernel
  series:

   - a big set of cleanups to the aged sysfs interface from Johan
     Hovold.  To get these in, v4.1-rc3 was merged into the tree as the
     first patch in that series had to go into stable.  This makes the
     locking much more fine-grained (get rid of the "big GPIO lock(s)"
     and store states in the GPIO descriptors.

   - rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value() to
     avoid confusions.

   - New drivers for:
      * NXP LPC18xx (currently LPC1850)
      * NetLogic XLP
      * Broadcom STB SoC's
      * Axis ETRAXFS
      * Zynq Ultrascale+ (subdriver)

   - ACPI:
      * make it possible to retrieve GpioInt resources from a GPIO
        device using acpi_dev_gpio_irq_get()
      * merge some dependent I2C changes exploiting this.
      * support the ARM X-Gene GPIO standby driver.

   - make it possible for the generic GPIO driver to read back the value
     set registers to reflect current status.

   - loads of OMAP IRQ handling fixes.

   - incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
     PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.

   - janitorial (constification, checkpatch cleanups)"

* tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
  gpio: Fix checkpatch.pl issues
  gpio: pcf857x: handle only enabled irqs
  gpio / ACPI: Return -EPROBE_DEFER if the gpiochip was not found
  GPIO / ACPI: export acpi_gpiochip_request(free)_interrupts for module use
  gpio: improve error reporting on own descriptors
  gpio: promote own request failure to pr_err()
  gpio: Added support to Zynq Ultrascale+ MPSoC
  gpio: add ETRAXFS GPIO driver
  fix documentation after renaming gpiod_set_array to gpiod_set_array_value
  gpio: Add GPIO support for Broadcom STB SoCs
  gpio: xgene: add ACPI support for APM X-Gene GPIO standby driver
  gpio: tb10x: Drop unneeded free_irq() call
  gpio: crystalcove: set IRQCHIP_SKIP_SET_WAKE for the irqchip
  gpio: stp-xway: Use the of_property_read_u32 helper
  gpio: pcf857x: Check for irq_set_irq_wake() failures
  gpio-stp-xway: Fix enabling the highest bit of the PHY LEDs
  gpio: Prevent an integer overflow in the pca953x driver
  gpio: omap: rework omap_gpio_irq_startup to handle current pin state properly
  gpio: omap: rework omap_gpio_request to touch only gpio specific registers
  gpio: omap: rework omap_x_irq_shutdown to touch only irqs specific registers
  ...

9 files changed, 187 insertions, 40 deletions

diff --git a/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt b/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt
new file mode 100644
index 000000000000..435f1bcca341
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt
@@ -0,0 +1,65 @@
+Broadcom STB "UPG GIO" GPIO controller
+
+The controller's registers are organized as sets of eight 32-bit
+registers with each set controlling a bank of up to 32 pins.  A single
+interrupt is shared for all of the banks handled by the controller.
+
+Required properties:
+
+- compatible:
+    Must be "brcm,brcmstb-gpio"
+
+- reg:
+    Define the base and range of the I/O address space containing
+    the brcmstb GPIO controller registers
+
+- #gpio-cells:
+    Should be <2>.  The first cell is the pin number (within the controller's
+    pin space), and the second is used for the following:
+    bit[0]: polarity (0 for active-high, 1 for active-low)
+
+- gpio-controller:
+    Specifies that the node is a GPIO controller.
+
+- brcm,gpio-bank-widths:
+    Number of GPIO lines for each bank.  Number of elements must
+    correspond to number of banks suggested by the 'reg' property.
+
+Optional properties:
+
+- interrupts:
+    The interrupt shared by all GPIO lines for this controller.
+
+- interrupt-parent:
+    phandle of the parent interrupt controller
+
+- #interrupt-cells:
+    Should be <2>.  The first cell is the GPIO number, the second should specify
+    flags.  The following subset of flags is supported:
+    - bits[3:0] trigger type and level flags
+        1 = low-to-high edge triggered
+        2 = high-to-low edge triggered
+        4 = active high level-sensitive
+        8 = active low level-sensitive
+      Valid combinations are 1, 2, 3, 4, 8.
+    See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+
+- interrupt-controller:
+    Marks the device node as an interrupt controller
+
+- interrupt-names:
+    The name of the IRQ resource used by this controller
+
+Example:
+	upg_gio: gpio@f040a700 {
+		#gpio-cells = <0x2>;
+		#interrupt-cells = <0x2>;
+		compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio";
+		gpio-controller;
+		interrupt-controller;
+		reg = <0xf040a700 0x80>;
+		interrupt-parent = <0xf>;
+		interrupts = <0x6>;
+		interrupt-names = "upg_gio";
+		brcm,gpio-bank-widths = <0x20 0x20 0x20 0x18>;
+	};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-etraxfs.txt b/Documentation/devicetree/bindings/gpio/gpio-etraxfs.txt
new file mode 100644
index 000000000000..abf4db736c6e
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-etraxfs.txt
@@ -0,0 +1,21 @@
+Axis ETRAX FS General I/O controller bindings
+
+Required properties:
+
+- compatible:
+  - "axis,etraxfs-gio"
+- reg: Physical base address and length of the controller's registers.
+- #gpio-cells: Should be 3
+  - The first cell is the gpio offset number.
+  - The second cell is reserved and is currently unused.
+  - The third cell is the port number (hex).
+- gpio-controller: Marks the device node as a GPIO controller.
+
+Example:
+
+	gio: gpio@b001a000 {
+		compatible = "axis,etraxfs-gio";
+		reg = <0xb001a000 0x1000>;
+		gpio-controller;
+		#gpio-cells = <3>;
+	};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-xlp.txt b/Documentation/devicetree/bindings/gpio/gpio-xlp.txt
new file mode 100644
index 000000000000..262ee4ddf2cb
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-xlp.txt
@@ -0,0 +1,47 @@
+Netlogic XLP Family GPIO
+========================
+
+This GPIO driver is used for following Netlogic XLP SoCs:
+	XLP832, XLP316, XLP208, XLP980, XLP532
+
+Required properties:
+-------------------
+
+- compatible: Should be one of the following:
+  - "netlogic,xlp832-gpio": For Netlogic XLP832
+  - "netlogic,xlp316-gpio": For Netlogic XLP316
+  - "netlogic,xlp208-gpio": For Netlogic XLP208
+  - "netlogic,xlp980-gpio": For Netlogic XLP980
+  - "netlogic,xlp532-gpio": For Netlogic XLP532
+- reg: Physical base address and length of the controller's registers.
+- #gpio-cells: Should be two. The first cell is the pin number and the second
+  cell is used to specify optional parameters (currently unused).
+- gpio-controller: Marks the device node as a GPIO controller.
+- nr-gpios: Number of GPIO pins supported by the controller.
+- interrupt-cells: Should be two. The first cell is the GPIO Number. The
+  second cell is used to specify flags. The following subset of flags is
+  supported:
+  - trigger type:
+	1 = low to high edge triggered.
+	2 = high to low edge triggered.
+	4 = active high level-sensitive.
+	8 = active low level-sensitive.
+- interrupts: Interrupt number for this device.
+- interrupt-parent: phandle of the parent interrupt controller.
+- interrupt-controller: Identifies the node as an interrupt controller.
+
+Example:
+
+	gpio: xlp_gpio@34000 {
+		compatible = "netlogic,xlp316-gpio";
+		reg = <0 0x34100 0x1000
+		       0 0x35100 0x1000>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		nr-gpios = <57>;
+
+		#interrupt-cells = <2>;
+		interrupt-parent = <&pic>;
+		interrupts = <39>;
+		interrupt-controller;
+	};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-zynq.txt b/Documentation/devicetree/bindings/gpio/gpio-zynq.txt
index 986371a4be2c..db4c6a663c03 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-zynq.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-zynq.txt
@@ -6,7 +6,7 @@ Required properties:
 			  - First cell is the GPIO line number
 			  - Second cell is used to specify optional
 			    parameters (unused)
-- compatible		: Should be "xlnx,zynq-gpio-1.0"
+- compatible		: Should be "xlnx,zynq-gpio-1.0" or "xlnx,zynqmp-gpio-1.0"
 - clocks		: Clock specifier (see clock bindings for details)
 - gpio-controller	: Marks the device node as a GPIO controller.
 - interrupts		: Interrupt specifier (see interrupt bindings for
diff --git a/Documentation/devicetree/bindings/gpio/nxp,lpc1850-gpio.txt b/Documentation/devicetree/bindings/gpio/nxp,lpc1850-gpio.txt
new file mode 100644
index 000000000000..eb7cdd69e10b
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/nxp,lpc1850-gpio.txt
@@ -0,0 +1,39 @@
+NXP LPC18xx/43xx GPIO controller Device Tree Bindings
+-----------------------------------------------------
+
+Required properties:
+- compatible		: Should be "nxp,lpc1850-gpio"
+- reg			: Address and length of the register set for the device
+- clocks		: Clock specifier (see clock bindings for details)
+- gpio-controller	: Marks the device node as a GPIO controller.
+- #gpio-cells 		: Should be two
+			  - First cell is the GPIO line number
+			  - Second cell is used to specify polarity
+
+Optional properties:
+- gpio-ranges		: Mapping between GPIO and pinctrl
+
+Example:
+#define LPC_GPIO(port, pin)	(port * 32 + pin)
+#define LPC_PIN(port, pin)	(0x##port * 32 + pin)
+
+gpio: gpio@400f4000 {
+	compatible = "nxp,lpc1850-gpio";
+	reg = <0x400f4000 0x4000>;
+	clocks = <&ccu1 CLK_CPU_GPIO>;
+	gpio-controller;
+	#gpio-cells = <2>;
+	gpio-ranges =	<&pinctrl LPC_GPIO(0,0)  LPC_PIN(0,0)  2>,
+			...
+			<&pinctrl LPC_GPIO(7,19) LPC_PIN(f,5)  7>;
+};
+
+gpio_joystick {
+	compatible = "gpio-keys-polled";
+	...
+
+	button@0 {
+		...
+		gpios = <&gpio LPC_GPIO(4,8) GPIO_ACTIVE_LOW>;
+	};
+};
diff --git a/Documentation/gpio/consumer.txt b/Documentation/gpio/consumer.txt
index c21c1313f09e..bbc8b5888b80 100644
--- a/Documentation/gpio/consumer.txt
+++ b/Documentation/gpio/consumer.txt
@@ -241,18 +241,18 @@ Set multiple GPIO outputs with a single function call
 -----------------------------------------------------
 The following functions set the output values of an array of GPIOs:
 
-	void gpiod_set_array(unsigned int array_size,
-			     struct gpio_desc **desc_array,
-			     int *value_array)
-	void gpiod_set_raw_array(unsigned int array_size,
-				 struct gpio_desc **desc_array,
-				 int *value_array)
-	void gpiod_set_array_cansleep(unsigned int array_size,
-				      struct gpio_desc **desc_array,
-				      int *value_array)
-	void gpiod_set_raw_array_cansleep(unsigned int array_size,
-					  struct gpio_desc **desc_array,
-					  int *value_array)
+	void gpiod_set_array_value(unsigned int array_size,
+				   struct gpio_desc **desc_array,
+				   int *value_array)
+	void gpiod_set_raw_array_value(unsigned int array_size,
+				       struct gpio_desc **desc_array,
+				       int *value_array)
+	void gpiod_set_array_value_cansleep(unsigned int array_size,
+					    struct gpio_desc **desc_array,
+					    int *value_array)
+	void gpiod_set_raw_array_value_cansleep(unsigned int array_size,
+						struct gpio_desc **desc_array,
+						int *value_array)
 
 The array can be an arbitrary set of GPIOs. The functions will try to set
 GPIOs belonging to the same bank or chip simultaneously if supported by the
@@ -271,8 +271,8 @@ matches the desired group of GPIOs, those GPIOs can be set by simply using
 the struct gpio_descs returned by gpiod_get_array():
 
 	struct gpio_descs *my_gpio_descs = gpiod_get_array(...);
-	gpiod_set_array(my_gpio_descs->ndescs, my_gpio_descs->desc,
-			my_gpio_values);
+	gpiod_set_array_value(my_gpio_descs->ndescs, my_gpio_descs->desc,
+			      my_gpio_values);
 
 It is also possible to set a completely arbitrary array of descriptors. The
 descriptors may be obtained using any combination of gpiod_get() and
diff --git a/Documentation/gpio/gpio-legacy.txt b/Documentation/gpio/gpio-legacy.txt
index 6f83fa965b4b..79ab5648d69b 100644
--- a/Documentation/gpio/gpio-legacy.txt
+++ b/Documentation/gpio/gpio-legacy.txt
@@ -751,9 +751,6 @@ requested using gpio_request():
 	int gpio_export_link(struct device *dev, const char *name,
 		unsigned gpio)
 
-	/* change the polarity of a GPIO node in sysfs */
-	int gpio_sysfs_set_active_low(unsigned gpio, int value);
-
 After a kernel driver requests a GPIO, it may only be made available in
 the sysfs interface by gpio_export().  The driver can control whether the
 signal direction may change.  This helps drivers prevent userspace code
@@ -767,9 +764,3 @@ After the GPIO has been exported, gpio_export_link() allows creating
 symlinks from elsewhere in sysfs to the GPIO sysfs node.  Drivers can
 use this to provide the interface under their own device in sysfs with
 a descriptive name.
-
-Drivers can use gpio_sysfs_set_active_low() to hide GPIO line polarity
-differences between boards from user space.  This only affects the
-sysfs interface.  Polarity change can be done both before and after
-gpio_export(), and previously enabled poll(2) support for either
-rising or falling edge will be reconfigured to follow this setting.
diff --git a/Documentation/gpio/sysfs.txt b/Documentation/gpio/sysfs.txt
index c2c3a97f8ff7..535b6a8a7a7c 100644
--- a/Documentation/gpio/sysfs.txt
+++ b/Documentation/gpio/sysfs.txt
@@ -132,9 +132,6 @@ requested using gpio_request():
 	int gpiod_export_link(struct device *dev, const char *name,
 		      struct gpio_desc *desc);
 
-	/* change the polarity of a GPIO node in sysfs */
-	int gpiod_sysfs_set_active_low(struct gpio_desc *desc, int value);
-
 After a kernel driver requests a GPIO, it may only be made available in
 the sysfs interface by gpiod_export(). The driver can control whether the
 signal direction may change. This helps drivers prevent userspace code
@@ -148,8 +145,3 @@ After the GPIO has been exported, gpiod_export_link() allows creating
 symlinks from elsewhere in sysfs to the GPIO sysfs node. Drivers can
 use this to provide the interface under their own device in sysfs with
 a descriptive name.
-
-Drivers can use gpiod_sysfs_set_active_low() to hide GPIO line polarity
-differences between boards from user space. Polarity change can be done both
-before and after gpiod_export(), and previously enabled poll(2) support for
-either rising or falling edge will be reconfigured to follow this setting.
diff --git a/Documentation/zh_CN/gpio.txt b/Documentation/zh_CN/gpio.txt
index d5b8f01833f4..bce972521065 100644
--- a/Documentation/zh_CN/gpio.txt
+++ b/Documentation/zh_CN/gpio.txt
@@ -638,9 +638,6 @@ GPIO 控制器的路径类似 /sys/class/gpio/gpiochip42/ (对于从#42 GPIO
 	int gpio_export_link(struct device *dev, const char *name,
 		unsigned gpio)
 
-	/* 改变 sysfs 中的一个 GPIO 节点的极性 */
-	int gpio_sysfs_set_active_low(unsigned gpio, int value);
-
 在一个内核驱动申请一个 GPIO 之后，它可以通过 gpio_export()使其在 sysfs
 接口中可见。该驱动可以控制信号方向是否可修改。这有助于防止用户空间代码无意间
 破坏重要的系统状态。
@@ -651,8 +648,3 @@ GPIO 控制器的路径类似 /sys/class/gpio/gpiochip42/ (对于从#42 GPIO
 在 GPIO 被导出之后，gpio_export_link()允许在 sysfs 文件系统的任何地方
 创建一个到这个 GPIO sysfs 节点的符号链接。这样驱动就可以通过一个描述性的
 名字，在 sysfs 中他们所拥有的设备下提供一个(到这个 GPIO sysfs 节点的)接口。
-
-驱动可以使用 gpio_sysfs_set_active_low() 来在用户空间隐藏电路板之间
-GPIO 线的极性差异。这个仅对 sysfs 接口起作用。极性的改变可以在 gpio_export()
-前后进行,且之前使能的轮询操作(poll(2))支持(上升或下降沿)将会被重新配置来遵循
-这个设置。