diff options
| -rw-r--r-- | Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt | 461 |
1 files changed, 461 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt new file mode 100644 index 000000000000..9e9e9ef9f852 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/brcm,capri-pinctrl.txt @@ -0,0 +1,461 @@ +Broadcom Capri Pin Controller + +This is a pin controller for the Broadcom BCM281xx SoC family, which includes +BCM11130, BCM11140, BCM11351, BCM28145, and BCM28155 SoCs. + +=== Pin Controller Node === + +Required Properties: + +- compatible: Must be "brcm,capri-pinctrl". +- reg: Base address of the PAD Controller register block and the size + of the block. + +For example, the following is the bare minimum node: + + pinctrl@35004800 { + compatible = "brcm,capri-pinctrl"; + reg = <0x35004800 0x430>; + }; + +As a pin controller device, in addition to the required properties, this node +should also contain the pin configuration nodes that client devices reference, +if any. + +=== Pin Configuration Node === + +Each pin configuration node is a sub-node of the pin controller node and is a +container of an arbitrary number of subnodes, called pin group nodes in this +document. + +Please refer to the pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the definition of a +"pin configuration node". + +=== Pin Group Node === + +A pin group node specifies the desired pin mux and/or pin configuration for an +arbitrary number of pins. The name of the pin group node is optional and not +used. + +A pin group node only affects the properties specified in the node, and has no +effect on any properties that are omitted. + +The pin group node accepts a subset of the generic pin config properties. For +details generic pin config properties, please refer to pinctrl-bindings.txt +and <include/linux/pinctrl/pinconfig-generic.h>. + +Each pin controlled by this pin controller belong to one of three types: +Standard, I2C, and HDMI. Each type accepts a different set of pin config +properties. A list of pins and their types is provided below. + +Required Properties (applicable to all pins): + +- pins: Multiple strings. Specifies the name(s) of one or more pins to + be configured by this node. + +Optional Properties (for standard pins): + +- function: String. Specifies the pin mux selection. Values + must be one of: "alt1", "alt2", "alt3", "alt4" +- input-schmitt-enable: No arguments. Enable schmitt-trigger mode. +- input-schmitt-disable: No arguments. Disable schmitt-trigger mode. +- bias-pull-up: No arguments. Pull up on pin. +- bias-pull-down: No arguments. Pull down on pin. +- bias-disable: No arguments. Disable pin bias. +- slew-rate: Integer. Meaning depends on configured pin mux: + *_SCL or *_SDA: + 0: Standard(100kbps)& Fast(400kbps) mode + 1: Highspeed (3.4Mbps) mode + IC_DM or IC_DP: + 0: normal slew rate + 1: fast slew rate + Otherwise: + 0: fast slew rate + 1: normal slew rate +- input-enable: No arguements. Enable input (does not affect + output.) +- input-disable: No arguements. Disable input (does not affect + output.) +- drive-strength: Integer. Drive strength in mA. Valid values are + 2, 4, 6, 8, 10, 12, 14, 16 mA. + +Optional Properties (for I2C pins): + +- function: String. Specifies the pin mux selection. Values + must be one of: "alt1", "alt2", "alt3", "alt4" +- bias-pull-up: Integer. Pull up strength in Ohm. There are 3 + pull-up resisitors (1.2k, 1.8k, 2.7k) available + in parallel for I2C pins, so the valid values + are: 568, 720, 831, 1080, 1200, 1800, 2700 Ohm. +- bias-disable: No arguments. Disable pin bias. +- slew-rate: Integer. Meaning depends on configured pin mux: + *_SCL or *_SDA: + 0: Standard(100kbps)& Fast(400kbps) mode + 1: Highspeed (3.4Mbps) mode + IC_DM or IC_DP: + 0: normal slew rate + 1: fast slew rate + Otherwise: + 0: fast slew rate + 1: normal slew rate +- input-enable: No arguements. Enable input (does not affect + output.) +- input-disable: No arguements. Disable input (does not affect + output.) + +Optional Properties (for HDMI pins): + +- function: String. Specifies the pin mux selection. Values + must be one of: "alt1", "alt2", "alt3", "alt4" +- slew-rate: Integer. Controls slew rate. + 0: Standard(100kbps)& Fast(400kbps) mode + 1: Highspeed (3.4Mbps) mode +- input-enable: No arguements. Enable input (does not affect + output.) +- input-disable: No arguements. Disable input (does not affect + output.) + +Example: +// pin controller node +pinctrl@35004800 { + compatible = "brcm,capri-pinctrl"; + reg = <0x35004800 0x430>; + + // pin configuration node + dev_a_default: dev_a_active { + //group node defining 1 standard pin + grp_1 { + pins = "std_pin1"; + function = "alt1"; + input-schmitt-enable; + bias-disable; + slew-rate = <1>; + drive-strength = <4>; + }; + + // group node defining 2 I2C pins + grp_2 { + pins = "i2c_pin1", "i2c_pin2"; + function = "alt2"; + bias-pull-up = <720>; + input-enable; + }; + + // group node defining 2 HDMI pins + grp_3 { + pins = "hdmi_pin1", "hdmi_pin2"; + function = "alt3"; + slew-rate = <1>; + }; + + // other pin group nodes + ... + }; + + // other pin configuration nodes + ... +}; + +In the example above, "dev_a_active" is a pin configuration node with a number +of sub-nodes. In the pin group node "grp_1", one pin, "std_pin1", is defined in +the "pins" property. Thus, the remaining properties in the "grp_1" node applies +only to this pin, including the following settings: + - setting pinmux to "alt1" + - enabling schmitt-trigger (hystersis) mode + - disabling pin bias + - setting the slew-rate to 1 + - setting the drive strength to 4 mA +Note that neither "input-enable" nor "input-disable" was specified - the pinctrl +subsystem will therefore leave this property unchanged from whatever state it +was in before applying these changes. + +The "pins" property in the pin group node "grp_2" specifies two pins - +"i2c_pin1" and "i2c_pin2"; the remaining properties in this pin group node, +therefore, applies to both of these pins. The properties include: + - setting pinmux to "alt2" + - setting pull-up resistance to 720 Ohm (ie. enabling 1.2k and 1.8k resistors + in parallel) + - enabling both pins' input +"slew-rate" is not specified in this pin group node, so the slew-rate for these +pins are left as-is. + +Finally, "grp_3" defines two HDMI pins. The following properties are applied to +both pins: + - setting pinmux to "alt3" + - setting slew-rate to 1; for HDMI pins, this corresponds to the 3.4 Mbps + Highspeed mode +The input is neither enabled or disabled, and is left untouched. + +=== Pin Names and Type === + +The following are valid pin names and their pin types: + + "adcsync", Standard + "bat_rm", Standard + "bsc1_scl", I2C + "bsc1_sda", I2C + "bsc2_scl", I2C + "bsc2_sda", I2C + "classgpwr", Standard + "clk_cx8", Standard + "clkout_0", Standard + "clkout_1", Standard + "clkout_2", Standard + "clkout_3", Standard + "clkreq_in_0", Standard + "clkreq_in_1", Standard + "cws_sys_req1", Standard + "cws_sys_req2", Standard + "cws_sys_req3", Standard + "digmic1_clk", Standard + "digmic1_dq", Standard + "digmic2_clk", Standard + "digmic2_dq", Standard + "gpen13", Standard + "gpen14", Standard + "gpen15", Standard + "gpio00", Standard + "gpio01", Standard + "gpio02", Standard + "gpio03", Standard + "gpio04", Standard + "gpio05", Standard + "gpio06", Standard + "gpio07", Standard + "gpio08", Standard + "gpio09", Standard + "gpio10", Standard + "gpio11", Standard + "gpio12", Standard + "gpio13", Standard + "gpio14", Standard + "gps_pablank", Standard + "gps_tmark", Standard + "hdmi_scl", HDMI + "hdmi_sda", HDMI + "ic_dm", Standard + "ic_dp", Standard + "kp_col_ip_0", Standard + "kp_col_ip_1", Standard + "kp_col_ip_2", Standard + "kp_col_ip_3", Standard + "kp_row_op_0", Standard + "kp_row_op_1", Standard + "kp_row_op_2", Standard + "kp_row_op_3", Standard + "lcd_b_0", Standard + "lcd_b_1", Standard + "lcd_b_2", Standard + "lcd_b_3", Standard + "lcd_b_4", Standard + "lcd_b_5", Standard + "lcd_b_6", Standard + "lcd_b_7", Standard + "lcd_g_0", Standard + "lcd_g_1", Standard + "lcd_g_2", Standard + "lcd_g_3", Standard + "lcd_g_4", Standard + "lcd_g_5", Standard + "lcd_g_6", Standard + "lcd_g_7", Standard + "lcd_hsync", Standard + "lcd_oe", Standard + "lcd_pclk", Standard + "lcd_r_0", Standard + "lcd_r_1", Standard + "lcd_r_2", Standard + "lcd_r_3", Standard + "lcd_r_4", Standard + "lcd_r_5", Standard + "lcd_r_6", Standard + "lcd_r_7", Standard + "lcd_vsync", Standard + "mdmgpio0", Standard + "mdmgpio1", Standard + "mdmgpio2", Standard + "mdmgpio3", Standard + "mdmgpio4", Standard + "mdmgpio5", Standard + "mdmgpio6", Standard + "mdmgpio7", Standard + "mdmgpio8", Standard + "mphi_data_0", Standard + "mphi_data_1", Standard + "mphi_data_2", Standard + "mphi_data_3", Standard + "mphi_data_4", Standard + "mphi_data_5", Standard + "mphi_data_6", Standard + "mphi_data_7", Standard + "mphi_data_8", Standard + "mphi_data_9", Standard + "mphi_data_10", Standard + "mphi_data_11", Standard + "mphi_data_12", Standard + "mphi_data_13", Standard + "mphi_data_14", Standard + "mphi_data_15", Standard + "mphi_ha0", Standard + "mphi_hat0", Standard + "mphi_hat1", Standard + "mphi_hce0_n", Standard + "mphi_hce1_n", Standard + "mphi_hrd_n", Standard + "mphi_hwr_n", Standard + "mphi_run0", Standard + "mphi_run1", Standard + "mtx_scan_clk", Standard + "mtx_scan_data", Standard + "nand_ad_0", Standard + "nand_ad_1", Standard + "nand_ad_2", Standard + "nand_ad_3", Standard + "nand_ad_4", Standard + "nand_ad_5", Standard + "nand_ad_6", Standard + "nand_ad_7", Standard + "nand_ale", Standard + "nand_cen_0", Standard + "nand_cen_1", Standard + "nand_cle", Standard + "nand_oen", Standard + "nand_rdy_0", Standard + "nand_rdy_1", Standard + "nand_wen", Standard + "nand_wp", Standard + "pc1", Standard + "pc2", Standard + "pmu_int", Standard + "pmu_scl", I2C + "pmu_sda", I2C + "rfst2g_mtsloten3g", Standard + "rgmii_0_rx_ctl", Standard + "rgmii_0_rxc", Standard + "rgmii_0_rxd_0", Standard + "rgmii_0_rxd_1", Standard + "rgmii_0_rxd_2", Standard + "rgmii_0_rxd_3", Standard + "rgmii_0_tx_ctl", Standard + "rgmii_0_txc", Standard + "rgmii_0_txd_0", Standard + "rgmii_0_txd_1", Standard + "rgmii_0_txd_2", Standard + "rgmii_0_txd_3", Standard + "rgmii_1_rx_ctl", Standard + "rgmii_1_rxc", Standard + "rgmii_1_rxd_0", Standard + "rgmii_1_rxd_1", Standard + "rgmii_1_rxd_2", Standard + "rgmii_1_rxd_3", Standard + "rgmii_1_tx_ctl", Standard + "rgmii_1_txc", Standard + "rgmii_1_txd_0", Standard + "rgmii_1_txd_1", Standard + "rgmii_1_txd_2", Standard + "rgmii_1_txd_3", Standard + "rgmii_gpio_0", Standard + "rgmii_gpio_1", Standard + "rgmii_gpio_2", Standard + "rgmii_gpio_3", Standard + "rtxdata2g_txdata3g1", Standard + "rtxen2g_txdata3g2", Standard + "rxdata3g0", Standard + "rxdata3g1", Standard + "rxdata3g2", Standard + "sdio1_clk", Standard + "sdio1_cmd", Standard + "sdio1_data_0", Standard + "sdio1_data_1", Standard + "sdio1_data_2", Standard + "sdio1_data_3", Standard + "sdio4_clk", Standard + "sdio4_cmd", Standard + "sdio4_data_0", Standard + "sdio4_data_1", Standard + "sdio4_data_2", Standard + "sdio4_data_3", Standard + "sim_clk", Standard + "sim_data", Standard + "sim_det", Standard + "sim_resetn", Standard + "sim2_clk", Standard + "sim2_data", Standard + "sim2_det", Standard + "sim2_resetn", Standard + "sri_c", Standard + "sri_d", Standard + "sri_e", Standard + "ssp_extclk", Standard + "ssp0_clk", Standard + "ssp0_fs", Standard + "ssp0_rxd", Standard + "ssp0_txd", Standard + "ssp2_clk", Standard + "ssp2_fs_0", Standard + "ssp2_fs_1", Standard + "ssp2_fs_2", Standard + "ssp2_fs_3", Standard + "ssp2_rxd_0", Standard + "ssp2_rxd_1", Standard + "ssp2_txd_0", Standard + "ssp2_txd_1", Standard + "ssp3_clk", Standard + "ssp3_fs", Standard + "ssp3_rxd", Standard + "ssp3_txd", Standard + "ssp4_clk", Standard + "ssp4_fs", Standard + "ssp4_rxd", Standard + "ssp4_txd", Standard + "ssp5_clk", Standard + "ssp5_fs", Standard + "ssp5_rxd", Standard + "ssp5_txd", Standard + "ssp6_clk", Standard + "ssp6_fs", Standard + "ssp6_rxd", Standard + "ssp6_txd", Standard + "stat_1", Standard + "stat_2", Standard + "sysclken", Standard + "traceclk", Standard + "tracedt00", Standard + "tracedt01", Standard + "tracedt02", Standard + "tracedt03", Standard + "tracedt04", Standard + "tracedt05", Standard + "tracedt06", Standard + "tracedt07", Standard + "tracedt08", Standard + "tracedt09", Standard + "tracedt10", Standard + "tracedt11", Standard + "tracedt12", Standard + "tracedt13", Standard + "tracedt14", Standard + "tracedt15", Standard + "txdata3g0", Standard + "txpwrind", Standard + "uartb1_ucts", Standard + "uartb1_urts", Standard + "uartb1_urxd", Standard + "uartb1_utxd", Standard + "uartb2_urxd", Standard + "uartb2_utxd", Standard + "uartb3_ucts", Standard + "uartb3_urts", Standard + "uartb3_urxd", Standard + "uartb3_utxd", Standard + "uartb4_ucts", Standard + "uartb4_urts", Standard + "uartb4_urxd", Standard + "uartb4_utxd", Standard + "vc_cam1_scl", I2C + "vc_cam1_sda", I2C + "vc_cam2_scl", I2C + "vc_cam2_sda", I2C + "vc_cam3_scl", I2C + "vc_cam3_sda", I2C |