diff options
25 files changed, 917 insertions, 141 deletions
diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index c96d8dcf98fd..4ab09f2202d4 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -3,28 +3,43 @@ SATA nodes are defined to describe on-chip Serial ATA controllers. Each SATA controller should have its own node. +It is possible, but not required, to represent each port as a sub-node. +It allows to enable each port independently when dealing with multiple +PHYs. + Required properties: - compatible : compatible string, one of: - "allwinner,sun4i-a10-ahci" - - "fsl,imx53-ahci" - - "fsl,imx6q-ahci" - "hisilicon,hisi-ahci" - "ibm,476gtr-ahci" - "marvell,armada-380-ahci" - "snps,dwc-ahci" - "snps,exynos5440-ahci" - "snps,spear-ahci" + - "generic-ahci" - interrupts : <interrupt mapping for SATA IRQ> - reg : <registers mapping> +Please note that when using "generic-ahci" you must also specify a SoC specific +compatible: + compatible = "manufacturer,soc-model-ahci", "generic-ahci"; + Optional properties: - dma-coherent : Present if dma operations are coherent - clocks : a list of phandle + clock specifier pairs - target-supply : regulator for SATA target power +- phys : reference to the SATA PHY node +- phy-names : must be "sata-phy" + +Required properties when using sub-nodes: +- #address-cells : number of cells to encode an address +- #size-cells : number of cells representing the size of an address + + +Sub-nodes required properties: +- reg : the port number +- phys : reference to the SATA PHY node -"fsl,imx53-ahci", "fsl,imx6q-ahci" required properties: -- clocks : must contain the sata, sata_ref and ahb clocks -- clock-names : must contain "ahb" for the ahb clock Examples: sata@ffe08000 { @@ -40,3 +55,23 @@ Examples: clocks = <&pll6 0>, <&ahb_gates 25>; target-supply = <®_ahci_5v>; }; + +With sub-nodes: + sata@f7e90000 { + compatible = "marvell,berlin2q-achi", "generic-ahci"; + reg = <0xe90000 0x1000>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&chip CLKID_SATA>; + #address-cells = <1>; + #size-cells = <0>; + + sata0: sata-port@0 { + reg = <0>; + phys = <&sata_phy 0>; + }; + + sata1: sata-port@1 { + reg = <1>; + phys = <&sata_phy 1>; + }; + }; diff --git a/Documentation/devicetree/bindings/ata/ahci-st.txt b/Documentation/devicetree/bindings/ata/ahci-st.txt new file mode 100644 index 000000000000..0574a77a0b9f --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ahci-st.txt @@ -0,0 +1,31 @@ +STMicroelectronics STi SATA controller + +This binding describes a SATA device. + +Required properties: + - compatible : Must be "st,sti-ahci" + - reg : Physical base addresses and length of register sets + - interrupts : Interrupt associated with the SATA device + - interrupt-names : Associated name must be; "hostc" + - resets : The power-down and soft-reset lines of SATA IP + - reset-names : Associated names must be; "pwr-dwn" and "sw-rst" + - clocks : The phandle for the clock + - clock-names : Associated name must be; "ahci_clk" + - phys : The phandle for the PHY device + - phy-names : Associated name must be; "ahci_phy" + +Example: + + sata0: sata@fe380000 { + compatible = "st,sti-ahci"; + reg = <0xfe380000 0x1000>; + interrupts = <GIC_SPI 157 IRQ_TYPE_NONE>; + interrupt-names = "hostc"; + phys = <&miphy365x_phy MIPHY_PORT_0 MIPHY_TYPE_SATA>; + phy-names = "ahci_phy"; + resets = <&powerdown STIH416_SATA0_POWERDOWN>, + <&softreset STIH416_SATA0_SOFTRESET>; + reset-names = "pwr-dwn", "sw-rst"; + clocks = <&clk_s_a0_ls CLK_ICN_REG>; + clock-names = "ahci_clk"; + }; diff --git a/Documentation/devicetree/bindings/ata/imx-sata.txt b/Documentation/devicetree/bindings/ata/imx-sata.txt new file mode 100644 index 000000000000..fa511db18408 --- /dev/null +++ b/Documentation/devicetree/bindings/ata/imx-sata.txt @@ -0,0 +1,36 @@ +* Freescale i.MX AHCI SATA Controller + +The Freescale i.MX SATA controller mostly conforms to the AHCI interface +with some special extensions at integration level. + +Required properties: +- compatible : should be one of the following: + - "fsl,imx53-ahci" for i.MX53 SATA controller + - "fsl,imx6q-ahci" for i.MX6Q SATA controller +- interrupts : interrupt mapping for SATA IRQ +- reg : registers mapping +- clocks : list of clock specifiers, must contain an entry for each + required entry in clock-names +- clock-names : should include "sata", "sata_ref" and "ahb" entries + +Optional properties: +- fsl,transmit-level-mV : transmit voltage level, in millivolts. +- fsl,transmit-boost-mdB : transmit boost level, in milli-decibels +- fsl,transmit-atten-16ths : transmit attenuation, in 16ths +- fsl,receive-eq-mdB : receive equalisation, in milli-decibels + Please refer to the technical documentation or the driver source code + for the list of legal values for these options. +- fsl,no-spread-spectrum : disable spread-spectrum clocking on the SATA + link. + +Examples: + +sata@02200000 { + compatible = "fsl,imx6q-ahci"; + reg = <0x02200000 0x4000>; + interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6QDL_CLK_SATA>, + <&clks IMX6QDL_CLK_SATA_REF_100M>, + <&clks IMX6QDL_CLK_AHB>; + clock-names = "sata", "sata_ref", "ahb"; +}; diff --git a/Documentation/devicetree/bindings/ata/tegra-sata.txt b/Documentation/devicetree/bindings/ata/tegra-sata.txt new file mode 100644 index 000000000000..946f2072570b --- /dev/null +++ b/Documentation/devicetree/bindings/ata/tegra-sata.txt @@ -0,0 +1,30 @@ +Tegra124 SoC SATA AHCI controller + +Required properties : +- compatible : "nvidia,tegra124-ahci". +- reg : Should contain 2 entries: + - AHCI register set (SATA BAR5) + - SATA register set +- interrupts : Defines the interrupt used by SATA +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names : Must include the following entries: + - sata + - sata-oob + - cml1 + - pll_e +- resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names : Must include the following entries: + - sata + - sata-oob + - sata-cold +- phys : Must contain an entry for each entry in phy-names. + See ../phy/phy-bindings.txt for details. +- phy-names : Must include the following entries: + - sata-phy : XUSB PADCTL SATA PHY +- hvdd-supply : Defines the SATA HVDD regulator +- vddio-supply : Defines the SATA VDDIO regulator +- avdd-supply : Defines the SATA AVDD regulator +- target-5v-supply : Defines the SATA 5V power regulator +- target-12v-supply : Defines the SATA 12V power regulator diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig index 7671dbac6015..e65d400efd44 100644 --- a/drivers/ata/Kconfig +++ b/drivers/ata/Kconfig @@ -141,6 +141,15 @@ config AHCI_SUNXI If unsure, say N. +config AHCI_TEGRA + tristate "NVIDIA Tegra124 AHCI SATA support" + depends on ARCH_TEGRA + help + This option enables support for the NVIDIA Tegra124 SoC's + onboard AHCI SATA. + + If unsure, say N. + config AHCI_XGENE tristate "APM X-Gene 6.0Gbps AHCI SATA host controller support" depends on PHY_XGENE diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile index 5a02aeecef5b..ae41107afc1f 100644 --- a/drivers/ata/Makefile +++ b/drivers/ata/Makefile @@ -15,6 +15,7 @@ obj-$(CONFIG_AHCI_IMX) += ahci_imx.o libahci.o libahci_platform.o obj-$(CONFIG_AHCI_MVEBU) += ahci_mvebu.o libahci.o libahci_platform.o obj-$(CONFIG_AHCI_SUNXI) += ahci_sunxi.o libahci.o libahci_platform.o obj-$(CONFIG_AHCI_ST) += ahci_st.o libahci.o libahci_platform.o +obj-$(CONFIG_AHCI_TEGRA) += ahci_tegra.o libahci.o libahci_platform.o obj-$(CONFIG_AHCI_XGENE) += ahci_xgene.o libahci.o libahci_platform.o # SFF w/ custom DMA diff --git a/drivers/ata/acard-ahci.c b/drivers/ata/acard-ahci.c index 0cd7c7a39e5b..25d0ac32e721 100644 --- a/drivers/ata/acard-ahci.c +++ b/drivers/ata/acard-ahci.c @@ -441,7 +441,7 @@ static int acard_ahci_init_one(struct pci_dev *pdev, const struct pci_device_id hpriv->mmio = pcim_iomap_table(pdev)[AHCI_PCI_BAR]; /* save initial config */ - ahci_save_initial_config(&pdev->dev, hpriv, 0, 0); + ahci_save_initial_config(&pdev->dev, hpriv); /* prepare host */ if (hpriv->cap & HOST_CAP_NCQ) diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c index 4cd52a4541a9..a29f8012fb08 100644 --- a/drivers/ata/ahci.c +++ b/drivers/ata/ahci.c @@ -526,8 +526,7 @@ static void ahci_pci_save_initial_config(struct pci_dev *pdev, "Disabling your PATA port. Use the boot option 'ahci.marvell_enable=0' to avoid this.\n"); } - ahci_save_initial_config(&pdev->dev, hpriv, force_port_map, - mask_port_map); + ahci_save_initial_config(&pdev->dev, hpriv); } static int ahci_pci_reset_controller(struct ata_host *host) diff --git a/drivers/ata/ahci.h b/drivers/ata/ahci.h index 5513296e5e2e..59ae0ee00149 100644 --- a/drivers/ata/ahci.h +++ b/drivers/ata/ahci.h @@ -53,7 +53,7 @@ enum { AHCI_MAX_PORTS = 32, - AHCI_MAX_CLKS = 3, + AHCI_MAX_CLKS = 4, AHCI_MAX_SG = 168, /* hardware max is 64K */ AHCI_DMA_BOUNDARY = 0xffffffff, AHCI_MAX_CMDS = 32, @@ -316,8 +316,12 @@ struct ahci_port_priv { }; struct ahci_host_priv { - void __iomem * mmio; /* bus-independent mem map */ + /* Input fields */ unsigned int flags; /* AHCI_HFLAG_* */ + u32 force_port_map; /* force port map */ + u32 mask_port_map; /* mask out particular bits */ + + void __iomem * mmio; /* bus-independent mem map */ u32 cap; /* cap to use */ u32 cap2; /* cap2 to use */ u32 port_map; /* port map to use */ @@ -330,7 +334,12 @@ struct ahci_host_priv { bool got_runtime_pm; /* Did we do pm_runtime_get? */ struct clk *clks[AHCI_MAX_CLKS]; /* Optional */ struct regulator *target_pwr; /* Optional */ - struct phy *phy; /* If platform uses phy */ + /* + * If platform uses PHYs. There is a 1:1 relation between the port number and + * the PHY position in this array. + */ + struct phy **phys; + unsigned nports; /* Number of ports */ void *plat_data; /* Other platform data */ /* * Optional ahci_start_engine override, if not set this gets set to the @@ -361,9 +370,7 @@ unsigned int ahci_dev_classify(struct ata_port *ap); void ahci_fill_cmd_slot(struct ahci_port_priv *pp, unsigned int tag, u32 opts); void ahci_save_initial_config(struct device *dev, - struct ahci_host_priv *hpriv, - unsigned int force_port_map, - unsigned int mask_port_map); + struct ahci_host_priv *hpriv); void ahci_init_controller(struct ata_host *host); int ahci_reset_controller(struct ata_host *host); diff --git a/drivers/ata/ahci_da850.c b/drivers/ata/ahci_da850.c index 2b77d53bccf8..ad1e71ec10cf 100644 --- a/drivers/ata/ahci_da850.c +++ b/drivers/ata/ahci_da850.c @@ -85,8 +85,7 @@ static int ahci_da850_probe(struct platform_device *pdev) da850_sata_init(dev, pwrdn_reg, hpriv->mmio); - rc = ahci_platform_init_host(pdev, hpriv, &ahci_da850_port_info, - 0, 0, 0); + rc = ahci_platform_init_host(pdev, hpriv, &ahci_da850_port_info); if (rc) goto disable_resources; diff --git a/drivers/ata/ahci_imx.c b/drivers/ata/ahci_imx.c index cac4360f272a..f3970b4ed889 100644 --- a/drivers/ata/ahci_imx.c +++ b/drivers/ata/ahci_imx.c @@ -64,6 +64,7 @@ struct imx_ahci_priv { struct regmap *gpr; bool no_device; bool first_time; + u32 phy_params; }; static int ahci_imx_hotplug; @@ -248,14 +249,7 @@ static int imx_sata_enable(struct ahci_host_priv *hpriv) IMX6Q_GPR13_SATA_TX_LVL_MASK | IMX6Q_GPR13_SATA_MPLL_CLK_EN | IMX6Q_GPR13_SATA_TX_EDGE_RATE, - IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB | - IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M | - IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F | - IMX6Q_GPR13_SATA_SPD_MODE_3P0G | - IMX6Q_GPR13_SATA_MPLL_SS_EN | - IMX6Q_GPR13_SATA_TX_ATTEN_9_16 | - IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB | - IMX6Q_GPR13_SATA_TX_LVL_1_025_V); + imxpriv->phy_params); regmap_update_bits(imxpriv->gpr, IOMUXC_GPR13, IMX6Q_GPR13_SATA_MPLL_CLK_EN, IMX6Q_GPR13_SATA_MPLL_CLK_EN); @@ -265,7 +259,7 @@ static int imx_sata_enable(struct ahci_host_priv *hpriv) ret = imx_sata_phy_reset(hpriv); if (ret) { dev_err(dev, "failed to reset phy: %d\n", ret); - goto disable_regulator; + goto disable_clk; } } @@ -273,6 +267,8 @@ static int imx_sata_enable(struct ahci_host_priv *hpriv) return 0; +disable_clk: + clk_disable_unprepare(imxpriv->sata_ref_clk); disable_regulator: if (hpriv->target_pwr) regulator_disable(hpriv->target_pwr); @@ -369,6 +365,165 @@ static const struct of_device_id imx_ahci_of_match[] = { }; MODULE_DEVICE_TABLE(of, imx_ahci_of_match); +struct reg_value { + u32 of_value; + u32 reg_value; +}; + +struct reg_property { + const char *name; + const struct reg_value *values; + size_t num_values; + u32 def_value; + u32 set_value; +}; + +static const struct reg_value gpr13_tx_level[] = { + { 937, IMX6Q_GPR13_SATA_TX_LVL_0_937_V }, + { 947, IMX6Q_GPR13_SATA_TX_LVL_0_947_V }, + { 957, IMX6Q_GPR13_SATA_TX_LVL_0_957_V }, + { 966, IMX6Q_GPR13_SATA_TX_LVL_0_966_V }, + { 976, IMX6Q_GPR13_SATA_TX_LVL_0_976_V }, + { 986, IMX6Q_GPR13_SATA_TX_LVL_0_986_V }, + { 996, IMX6Q_GPR13_SATA_TX_LVL_0_996_V }, + { 1005, IMX6Q_GPR13_SATA_TX_LVL_1_005_V }, + { 1015, IMX6Q_GPR13_SATA_TX_LVL_1_015_V }, + { 1025, IMX6Q_GPR13_SATA_TX_LVL_1_025_V }, + { 1035, IMX6Q_GPR13_SATA_TX_LVL_1_035_V }, + { 1045, IMX6Q_GPR13_SATA_TX_LVL_1_045_V }, + { 1054, IMX6Q_GPR13_SATA_TX_LVL_1_054_V }, + { 1064, IMX6Q_GPR13_SATA_TX_LVL_1_064_V }, + { 1074, IMX6Q_GPR13_SATA_TX_LVL_1_074_V }, + { 1084, IMX6Q_GPR13_SATA_TX_LVL_1_084_V }, + { 1094, IMX6Q_GPR13_SATA_TX_LVL_1_094_V }, + { 1104, IMX6Q_GPR13_SATA_TX_LVL_1_104_V }, + { 1113, IMX6Q_GPR13_SATA_TX_LVL_1_113_V }, + { 1123, IMX6Q_GPR13_SATA_TX_LVL_1_123_V }, + { 1133, IMX6Q_GPR13_SATA_TX_LVL_1_133_V }, + { 1143, IMX6Q_GPR13_SATA_TX_LVL_1_143_V }, + { 1152, IMX6Q_GPR13_SATA_TX_LVL_1_152_V }, + { 1162, IMX6Q_GPR13_SATA_TX_LVL_1_162_V }, + { 1172, IMX6Q_GPR13_SATA_TX_LVL_1_172_V }, + { 1182, IMX6Q_GPR13_SATA_TX_LVL_1_182_V }, + { 1191, IMX6Q_GPR13_SATA_TX_LVL_1_191_V }, + { 1201, IMX6Q_GPR13_SATA_TX_LVL_1_201_V }, + { 1211, IMX6Q_GPR13_SATA_TX_LVL_1_211_V }, + { 1221, IMX6Q_GPR13_SATA_TX_LVL_1_221_V }, + { 1230, IMX6Q_GPR13_SATA_TX_LVL_1_230_V }, + { 1240, IMX6Q_GPR13_SATA_TX_LVL_1_240_V } +}; + +static const struct reg_value gpr13_tx_boost[] = { + { 0, IMX6Q_GPR13_SATA_TX_BOOST_0_00_DB }, + { 370, IMX6Q_GPR13_SATA_TX_BOOST_0_37_DB }, + { 740, IMX6Q_GPR13_SATA_TX_BOOST_0_74_DB }, + { 1110, IMX6Q_GPR13_SATA_TX_BOOST_1_11_DB }, + { 1480, IMX6Q_GPR13_SATA_TX_BOOST_1_48_DB }, + { 1850, IMX6Q_GPR13_SATA_TX_BOOST_1_85_DB }, + { 2220, IMX6Q_GPR13_SATA_TX_BOOST_2_22_DB }, + { 2590, IMX6Q_GPR13_SATA_TX_BOOST_2_59_DB }, + { 2960, IMX6Q_GPR13_SATA_TX_BOOST_2_96_DB }, + { 3330, IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB }, + { 3700, IMX6Q_GPR13_SATA_TX_BOOST_3_70_DB }, + { 4070, IMX6Q_GPR13_SATA_TX_BOOST_4_07_DB }, + { 4440, IMX6Q_GPR13_SATA_TX_BOOST_4_44_DB }, + { 4810, IMX6Q_GPR13_SATA_TX_BOOST_4_81_DB }, + { 5280, IMX6Q_GPR13_SATA_TX_BOOST_5_28_DB }, + { 5750, IMX6Q_GPR13_SATA_TX_BOOST_5_75_DB } +}; + +static const struct reg_value gpr13_tx_atten[] = { + { 8, IMX6Q_GPR13_SATA_TX_ATTEN_8_16 }, + { 9, IMX6Q_GPR13_SATA_TX_ATTEN_9_16 }, + { 10, IMX6Q_GPR13_SATA_TX_ATTEN_10_16 }, + { 12, IMX6Q_GPR13_SATA_TX_ATTEN_12_16 }, + { 14, IMX6Q_GPR13_SATA_TX_ATTEN_14_16 }, + { 16, IMX6Q_GPR13_SATA_TX_ATTEN_16_16 }, +}; + +static const struct reg_value gpr13_rx_eq[] = { + { 500, IMX6Q_GPR13_SATA_RX_EQ_VAL_0_5_DB }, + { 1000, IMX6Q_GPR13_SATA_RX_EQ_VAL_1_0_DB }, + { 1500, IMX6Q_GPR13_SATA_RX_EQ_VAL_1_5_DB }, + { 2000, IMX6Q_GPR13_SATA_RX_EQ_VAL_2_0_DB }, + { 2500, IMX6Q_GPR13_SATA_RX_EQ_VAL_2_5_DB }, + { 3000, IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB }, + { 3500, IMX6Q_GPR13_SATA_RX_EQ_VAL_3_5_DB }, + { 4000, IMX6Q_GPR13_SATA_RX_EQ_VAL_4_0_DB }, +}; + +static const struct reg_property gpr13_props[] = { + { + .name = "fsl,transmit-level-mV", + .values = gpr13_tx_level, + .num_values = ARRAY_SIZE(gpr13_tx_level), + .def_value = IMX6Q_GPR13_SATA_TX_LVL_1_025_V, + }, { + .name = "fsl,transmit-boost-mdB", + .values = gpr13_tx_boost, + .num_values = ARRAY_SIZE(gpr13_tx_boost), + .def_value = IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB, + }, { + .name = "fsl,transmit-atten-16ths", + .values = gpr13_tx_atten, + .num_values = ARRAY_SIZE(gpr13_tx_atten), + .def_value = IMX6Q_GPR13_SATA_TX_ATTEN_9_16, + }, { + .name = "fsl,receive-eq-mdB", + .values = gpr13_rx_eq, + .num_values = ARRAY_SIZE(gpr13_rx_eq), + .def_value = IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB, + }, { + .name = "fsl,no-spread-spectrum", + .def_value = IMX6Q_GPR13_SATA_MPLL_SS_EN, + .set_value = 0, + }, +}; + +static u32 imx_ahci_parse_props(struct device *dev, + const struct reg_property *prop, size_t num) +{ + struct device_node *np = dev->of_node; + u32 reg_value = 0; + int i, j; + + for (i = 0; i < num; i++, prop++) { + u32 of_val; + + if (prop->num_values == 0) { + if (of_property_read_bool(np, prop->name)) + reg_value |= prop->set_value; + else + reg_value |= prop->def_value; + continue; + } + + if (of_property_read_u32(np, prop->name, &of_val)) { + dev_info(dev, "%s not specified, using %08x\n", + prop->name, prop->def_value); + reg_value |= prop->def_value; + continue; + } + + for (j = 0; j < prop->num_values; j++) { + if (prop->values[j].of_value == of_val) { + dev_info(dev, "%s value %u, using %08x\n", + prop->name, of_val, prop->values[j].reg_value); + reg_value |= prop->values[j].reg_value; + break; + } + } + + if (j == prop->num_values) { + dev_err(dev, "DT property %s is not a valid value\n", + prop->name); + reg_value |= prop->def_value; + } + } + + return reg_value; +} + static int imx_ahci_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; @@ -410,6 +565,8 @@ static int imx_ahci_probe(struct platform_device *pdev) } if (imxpriv->type == AHCI_IMX6Q) { + u32 reg_value; + imxpriv->gpr = syscon_regmap_lookup_by_compatible( "fsl,imx6q-iomuxc-gpr"); if (IS_ERR(imxpriv->gpr)) { @@ -417,6 +574,15 @@ static int imx_ahci_probe(struct platform_device *pdev) "failed to find fsl,imx6q-iomux-gpr regmap\n"); return PTR_ERR(imxpriv->gpr); } + + reg_value = imx_ahci_parse_props(dev, gpr13_props, + ARRAY_SIZE(gpr13_props)); + + imxpriv->phy_params = + IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M | + IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F | + IMX6Q_GPR13_SATA_SPD_MODE_3P0G | + reg_value; } hpriv = ahci_platform_get_resources(pdev); @@ -454,8 +620,7 @@ static int imx_ahci_probe(struct platform_device *pdev) reg_val = clk_get_rate(imxpriv->ahb_clk) / 1000; writel(reg_val, hpriv->mmio + IMX_TIMER1MS); - ret = ahci_platform_init_host(pdev, hpriv, &ahci_imx_port_info, - 0, 0, 0); + ret = ahci_platform_init_host(pdev, hpriv, &ahci_imx_port_info); if (ret) goto disable_sata; diff --git a/drivers/ata/ahci_mvebu.c b/drivers/ata/ahci_mvebu.c index fd3dfd733b84..68672d2692ee 100644 --- a/drivers/ata/ahci_mvebu.c +++ b/drivers/ata/ahci_mvebu.c @@ -88,8 +88,7 @@ static int ahci_mvebu_probe(struct platform_device *pdev) ahci_mvebu_mbus_config(hpriv, dram); ahci_mvebu_regret_option(hpriv); - rc = ahci_platform_init_host(pdev, hpriv, &ahci_mvebu_port_info, - 0, 0, 0); + rc = ahci_platform_init_host(pdev, hpriv, &ahci_mvebu_port_info); if (rc) goto disable_resources; diff --git a/drivers/ata/ahci_platform.c b/drivers/ata/ahci_platform.c index b10d81ddb528..f61ddb9146d6 100644 --- a/drivers/ata/ahci_platform.c +++ b/drivers/ata/ahci_platform.c @@ -34,7 +34,6 @@ static int ahci_probe(struct platform_device *pdev) struct device *dev = &pdev->dev; struct ahci_platform_data *pdata = dev_get_platdata(dev); struct ahci_host_priv *hpriv; - unsigned long hflags = 0; int rc; hpriv = ahci_platform_get_resources(pdev); @@ -58,10 +57,9 @@ static int ahci_probe(struct platform_device *pdev) } if (of_device_is_compatible(dev->of_node, "hisilicon,hisi-ahci")) - hflags |= AHCI_HFLAG_NO_FBS | AHCI_HFLAG_NO_NCQ; + hpriv->flags |= AHCI_HFLAG_NO_FBS | AHCI_HFLAG_NO_NCQ; - rc = ahci_platform_init_host(pdev, hpriv, &ahci_port_info, - hflags, 0, 0); + rc = ahci_platform_init_host(pdev, hpriv, &ahci_port_info); if (rc) goto pdata_exit; @@ -78,6 +76,8 @@ static SIMPLE_DEV_PM_OPS(ahci_pm_ops, ahci_platform_suspend, ahci_platform_resume); static const struct of_device_id ahci_of_match[] = { + { .compatible = "generic-ahci", }, + /* Keep the following compatibles for device tree compatibility */ { .compatible = "snps,spear-ahci", }, { .compatible = "snps,exynos5440-ahci", }, { .compatible = "ibm,476gtr-ahci", }, diff --git a/drivers/ata/ahci_st.c b/drivers/ata/ahci_st.c index 2595598df9ce..835d6eea84fd 100644 --- a/drivers/ata/ahci_st.c +++ b/drivers/ata/ahci_st.c @@ -166,7 +166,7 @@ static int st_ahci_probe(struct platform_device *pdev) if (err) return err; - err = ahci_platform_init_host(pdev, hpriv, &st_ahci_port_info, 0, 0, 0); + err = ahci_platform_init_host(pdev, hpriv, &st_ahci_port_info); if (err) { ahci_platform_disable_resources(hpriv); return err; @@ -221,7 +221,7 @@ static int st_ahci_resume(struct device *dev) static SIMPLE_DEV_PM_OPS(st_ahci_pm_ops, st_ahci_suspend, st_ahci_resume); -static struct of_device_id st_ahci_match[] = { +static const struct of_device_id st_ahci_match[] = { { .compatible = "st,ahci", }, {}, }; diff --git a/drivers/ata/ahci_sunxi.c b/drivers/ata/ahci_sunxi.c index 02002f125bd4..e44d675a30ec 100644 --- a/drivers/ata/ahci_sunxi.c +++ b/drivers/ata/ahci_sunxi.c @@ -167,7 +167,6 @@ static int ahci_sunxi_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; struct ahci_host_priv *hpriv; - unsigned long hflags; int rc; hpriv = ahci_platform_get_resources(pdev); @@ -184,11 +183,10 @@ static int ahci_sunxi_probe(struct platform_device *pdev) if (rc) goto disable_resources; - hflags = AHCI_HFLAG_32BIT_ONLY | AHCI_HFLAG_NO_MSI | - AHCI_HFLAG_NO_PMP | AHCI_HFLAG_YES_NCQ; + hpriv->flags = AHCI_HFLAG_32BIT_ONLY | AHCI_HFLAG_NO_MSI | + AHCI_HFLAG_NO_PMP | AHCI_HFLAG_YES_NCQ; - rc = ahci_platform_init_host(pdev, hpriv, &ahci_sunxi_port_info, - hflags, 0, 0); + rc = ahci_platform_init_host(pdev, hpriv, &ahci_sunxi_port_info); if (rc) goto disable_resources; diff --git a/drivers/ata/ahci_tegra.c b/drivers/ata/ahci_tegra.c new file mode 100644 index 000000000000..fc3df47fca35 --- /dev/null +++ b/drivers/ata/ahci_tegra.c @@ -0,0 +1,376 @@ +/* + * drivers/ata/ahci_tegra.c + * + * Copyright (c) 2014, NVIDIA CORPORATION. All rights reserved. + * + * Author: + * Mikko Perttunen <mperttunen@nvidia.com> + * + * This software is licensed under the terms of the GNU General Public + * License version 2, as published by the Free Software Foundation, and + * may be copied, distributed, and modified under those terms. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include <linux/ahci_platform.h> +#include <linux/reset.h> +#include <linux/errno.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/platform_device.h> +#include <linux/tegra-powergate.h> +#include <linux/regulator/consumer.h> +#include "ahci.h" + +#define SATA_CONFIGURATION_0 0x180 +#define SATA_CONFIGURATION_EN_FPCI BIT(0) + +#define SCFG_OFFSET 0x1000 + +#define T_SATA0_CFG_1 0x04 +#define T_SATA0_CFG_1_IO_SPACE BIT(0) +#define T_SATA0_CFG_1_MEMORY_SPACE BIT(1) +#define T_SATA0_CFG_1_BUS_MASTER BIT(2) +#define T_SATA0_CFG_1_SERR BIT(8) + +#define T_SATA0_CFG_9 0x24 +#define T_SATA0_CFG_9_BASE_ADDRESS_SHIFT 13 + +#define SATA_FPCI_BAR5 0x94 +#define SATA_FPCI_BAR5_START_SHIFT 4 + +#define SATA_INTR_MASK 0x188 +#define SATA_INTR_MASK_IP_INT_MASK BIT(16) + +#define T_SATA0_AHCI_HBA_CAP_BKDR 0x300 + +#define T_SATA0_BKDOOR_CC 0x4a4 + +#define T_SATA0_CFG_SATA 0x54c +#define T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN BIT(12) + +#define T_SATA0_CFG_MISC 0x550 + +#define T_SATA0_INDEX 0x680 + +#define T_SATA0_CHX_PHY_CTRL1_GEN1 0x690 +#define T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_MASK 0xff +#define T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT 0 +#define T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_MASK (0xff << 8) +#define T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT 8 + +#define T_SATA0_CHX_PHY_CTRL1_GEN2 0x694 +#define T_SATA0_CHX_PHY_CTRL1_GEN2_TX_AMP_MASK 0xff +#define T_SATA0_CHX_PHY_CTRL1_GEN2_TX_AMP_SHIFT 0 +#define T_SATA0_CHX_PHY_CTRL1_GEN2_TX_PEAK_MASK (0xff << 12) +#define T_SATA0_CHX_PHY_CTRL1_GEN2_TX_PEAK_SHIFT 12 + +#define T_SATA0_CHX_PHY_CTRL2 0x69c +#define T_SATA0_CHX_PHY_CTRL2_CDR_CNTL_GEN1 0x23 + +#define T_SATA0_CHX_PHY_CTRL11 0x6d0 +#define T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ (0x2800 << 16) + +#define FUSE_SATA_CALIB 0x124 +#define FUSE_SATA_CALIB_MASK 0x3 + +struct sata_pad_calibration { + u8 gen1_tx_amp; + u8 gen1_tx_peak; + u8 gen2_tx_amp; + u8 gen2_tx_peak; +}; + +static const struct sata_pad_calibration tegra124_pad_calibration[] = { + {0x18, 0x04, 0x18, 0x0a}, + {0x0e, 0x04, 0x14, 0x0a}, + {0x0e, 0x07, 0x1a, 0x0e}, + {0x14, 0x0e, 0x1a, 0x0e}, +}; + +struct tegra_ahci_priv { + struct platform_device *pdev; + void __iomem *sata_regs; + struct reset_control *sata_rst; + struct reset_control *sata_oob_rst; + struct reset_control *sata_cold_rst; + /* Needs special handling, cannot use ahci_platform */ + struct clk *sata_clk; + struct regulator_bulk_data supplies[5]; +}; + +static int tegra_ahci_power_on(struct ahci_host_priv *hpriv) +{ + struct tegra_ahci_priv *tegra = hpriv->plat_data; + int ret; + + ret = regulator_bulk_enable(ARRAY_SIZE(tegra->supplies), + tegra->supplies); + if (ret) + return ret; + + ret = tegra_powergate_sequence_power_up(TEGRA_POWERGATE_SATA, + tegra->sata_clk, + tegra->sata_rst); + if (ret) + goto disable_regulators; + + reset_control_assert(tegra->sata_oob_rst); + reset_control_assert(tegra->sata_cold_rst); + + ret = ahci_platform_enable_resources(hpriv); + if (ret) + goto disable_power; + + reset_control_deassert(tegra->sata_cold_rst); + reset_control_deassert(tegra->sata_oob_rst); + + return 0; + +disable_power: + clk_disable_unprepare(tegra->sata_clk); + + tegra_powergate_power_off(TEGRA_POWERGATE_SATA); + +disable_regulators: + regulator_bulk_disable(ARRAY_SIZE(tegra->supplies), tegra->supplies); + + return ret; +} + +static void tegra_ahci_power_off(struct ahci_host_priv *hpriv) +{ + struct tegra_ahci_priv *tegra = hpriv->plat_data; + + ahci_platform_disable_resources(hpriv); + + reset_control_assert(tegra->sata_rst); + reset_control_assert(tegra->sata_oob_rst); + reset_control_assert(tegra->sata_cold_rst); + + clk_disable_unprepare(tegra->sata_clk); + tegra_powergate_power_off(TEGRA_POWERGATE_SATA); + + regulator_bulk_disable(ARRAY_SIZE(tegra->supplies), tegra->supplies); +} + +static int tegra_ahci_controller_init(struct ahci_host_priv *hpriv) +{ + struct tegra_ahci_priv *tegra = hpriv->plat_data; + int ret; + unsigned int val; + struct sata_pad_calibration calib; + + ret = tegra_ahci_power_on(hpriv); + if (ret) { + dev_err(&tegra->pdev->dev, + "failed to power on AHCI controller: %d\n", ret); + return ret; + } + + val = readl(tegra->sata_regs + SATA_CONFIGURATION_0); + val |= SATA_CONFIGURATION_EN_FPCI; + writel(val, tegra->sata_regs + SATA_CONFIGURATION_0); + + /* Pad calibration */ + + /* FIXME Always use calibration 0. Change this to read the calibration + * fuse once the fuse driver has landed. */ + val = 0; + + calib = tegra124_pad_calibration[val & FUSE_SATA_CALIB_MASK]; + + writel(BIT(0), tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX); + + val = readl(tegra->sata_regs + + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN1); + val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_MASK; + val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_MASK; + val |= calib.gen1_tx_amp << + T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT; + val |= calib.gen1_tx_peak << + T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT; + writel(val, tegra->sata_regs + SCFG_OFFSET + + T_SATA0_CHX_PHY_CTRL1_GEN1); + + val = readl(tegra->sata_regs + + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN2); + val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_AMP_MASK; + val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_PEAK_MASK; + val |= calib.gen2_tx_amp << + T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT; + val |= calib.gen2_tx_peak << + T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT; + writel(val, tegra->sata_regs + SCFG_OFFSET + + T_SATA0_CHX_PHY_CTRL1_GEN2); + + writel(T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ, + tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL11); + writel(T_SATA0_CHX_PHY_CTRL2_CDR_CNTL_GEN1, + tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL2); + + writel(0, tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX); + + /* Program controller device ID */ + + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA); + val |= T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN; + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA); + + writel(0x01060100, tegra->sata_regs + SCFG_OFFSET + T_SATA0_BKDOOR_CC); + + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA); + val &= ~T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN; + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA); + + /* Enable IO & memory access, bus master mode */ + + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1); + val |= T_SATA0_CFG_1_IO_SPACE | T_SATA0_CFG_1_MEMORY_SPACE | + T_SATA0_CFG_1_BUS_MASTER | T_SATA0_CFG_1_SERR; + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1); + + /* Program SATA MMIO */ + + writel(0x10000 << SATA_FPCI_BAR5_START_SHIFT, + tegra->sata_regs + SATA_FPCI_BAR5); + + writel(0x08000 << T_SATA0_CFG_9_BASE_ADDRESS_SHIFT, + tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_9); + + /* Unmask SATA interrupts */ + + val = readl(tegra->sata_regs + SATA_INTR_MASK); + val |= SATA_INTR_MASK_IP_INT_MASK; + writel(val, tegra->sata_regs + SATA_INTR_MASK); + + return 0; +} + +static void tegra_ahci_controller_deinit(struct ahci_host_priv *hpriv) +{ + tegra_ahci_power_off(hpriv); +} + +static void tegra_ahci_host_stop(struct ata_host *host) +{ + struct ahci_host_priv *hpriv = host->private_data; + + tegra_ahci_controller_deinit(hpriv); +} + +static struct ata_port_operations ahci_tegra_port_ops = { + .inherits = &ahci_ops, + .host_stop = tegra_ahci_host_stop, +}; + +static const struct ata_port_info ahci_tegra_port_info = { + .flags = AHCI_FLAG_COMMON, + .pio_mask = ATA_PIO4, + .udma_mask = ATA_UDMA6, + .port_ops = &ahci_tegra_port_ops, +}; + +static const struct of_device_id tegra_ahci_of_match[] = { + { .compatible = "nvidia,tegra124-ahci" }, + {} +}; +MODULE_DEVICE_TABLE(of, tegra_ahci_of_match); + +static int tegra_ahci_probe(struct platform_device *pdev) +{ + struct ahci_host_priv *hpriv; + struct tegra_ahci_priv *tegra; + struct resource *res; + int ret; + + hpriv = ahci_platform_get_resources(pdev); + if (IS_ERR(hpriv)) + return PTR_ERR(hpriv); + + tegra = devm_kzalloc(&pdev->dev, sizeof(*tegra), GFP_KERNEL); + if (!tegra) + return -ENOMEM; + + hpriv->plat_data = tegra; + + tegra->pdev = pdev; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 1); + tegra->sata_regs = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(tegra->sata_regs)) + return PTR_ERR(tegra->sata_regs); + + tegra->sata_rst = devm_reset_control_get(&pdev->dev, "sata"); + if (IS_ERR(tegra->sata_rst)) { + dev_err(&pdev->dev, "Failed to get sata reset\n"); + return PTR_ERR(tegra->sata_rst); + } + + tegra->sata_oob_rst = devm_reset_control_get(&pdev->dev, "sata-oob"); + if (IS_ERR(tegra->sata_oob_rst)) { + dev_err(&pdev->dev, "Failed to get sata-oob reset\n"); + return PTR_ERR(tegra->sata_oob_rst); + } + + tegra->sata_cold_rst = devm_reset_control_get(&pdev->dev, "sata-cold"); + if (IS_ERR(tegra->sata_cold_rst)) { + dev_err(&pdev->dev, "Failed to get sata-cold reset\n"); + return PTR_ERR(tegra->sata_cold_rst); + } + + tegra->sata_clk = devm_clk_get(&pdev->dev, "sata"); + if (IS_ERR(tegra->sata_clk)) { + dev_err(&pdev->dev, "Failed to get sata clock\n"); + return PTR_ERR(tegra->sata_clk); + } + + tegra->supplies[0].supply = "avdd"; + tegra->supplies[1].supply = "hvdd"; + tegra->supplies[2].supply = "vddio"; + tegra->supplies[3].supply = "target-5v"; + tegra->supplies[4].supply = "target-12v"; + + ret = devm_regulator_bulk_get(&pdev->dev, ARRAY_SIZE(tegra->supplies), + tegra->supplies); + if (ret) { + dev_err(&pdev->dev, "Failed to get regulators\n"); + return ret; + } + + ret = tegra_ahci_controller_init(hpriv); + if (ret) + return ret; + + ret = ahci_platform_init_host(pdev, hpriv, &ahci_tegra_port_info); + if (ret) + goto deinit_controller; + + return 0; + +deinit_controller: + tegra_ahci_controller_deinit(hpriv); + + return ret; +}; + +static struct platform_driver tegra_ahci_driver = { + .probe = tegra_ahci_probe, + .remove = ata_platform_remove_one, + .driver = { + .name = "tegra-ahci", + .of_match_table = tegra_ahci_of_match, + }, + /* LP0 suspend support not implemented */ +}; +module_platform_driver(tegra_ahci_driver); + +MODULE_AUTHOR("Mikko Perttunen <mperttunen@nvidia.com>"); +MODULE_DESCRIPTION("Tegra124 AHCI SATA driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/ata/ahci_xgene.c b/drivers/ata/ahci_xgene.c index ee3a3659bd9e..bc281115490b 100644 --- a/drivers/ata/ahci_xgene.c +++ b/drivers/ata/ahci_xgene.c @@ -67,6 +67,9 @@ #define PORTAXICFG 0x000000bc #define PORTAXICFG_OUTTRANS_SET(dst, src) \ (((dst) & ~0x00f00000) | (((u32)(src) << 0x14) & 0x00f00000)) +#define PORTRANSCFG 0x000000c8 +#define PORTRANSCFG_RXWM_SET(dst, src) \ + (((dst) & ~0x0000007f) | (((u32)(src)) & 0x0000007f)) /* SATA host controller AXI CSR */ #define INT_SLV_TMOMASK 0x00000010 @@ -193,11 +196,11 @@ static void xgene_ahci_set_phy_cfg(struct xgene_ahci_context *ctx, int channel) /* Disable fix rate */ writel(0x0001fffe, mmio + PORTPHY1CFG); readl(mmio + PORTPHY1CFG); /* Force a barrier */ - writel(0x5018461c, mmio + PORTPHY2CFG); + writel(0x28183219, mmio + PORTPHY2CFG); readl(mmio + PORTPHY2CFG); /* Force a barrier */ - writel(0x1c081907, mmio + PORTPHY3CFG); + writel(0x13081008, mmio + PORTPHY3CFG); readl(mmio + PORTPHY3CFG); /* Force a barrier */ - writel(0x1c080815, mmio + PORTPHY4CFG); + writel(0x00480815, mmio + PORTPHY4CFG); readl(mmio + PORTPHY4CFG); /* Force a barrier */ /* Set window negotiation */ val = readl(mmio + PORTPHY5CFG); @@ -209,6 +212,10 @@ static void xgene_ahci_set_phy_cfg(struct xgene_ahci_context *ctx, int channel) val = PORTAXICFG_OUTTRANS_SET(val, 0xe); /* Set outstanding */ writel(val, mmio + PORTAXICFG); readl(mmio + PORTAXICFG); /* Force a barrier */ + /* Set the watermark threshold of the receive FIFO */ + val = readl(mmio + PORTRANSCFG); + val = PORTRANSCFG_RXWM_SET(val, 0x30); + writel(val, mmio + PORTRANSCFG); } /** @@ -415,7 +422,6 @@ static int xgene_ahci_probe(struct platform_device *pdev) struct ahci_host_priv *hpriv; struct xgene_ahci_context *ctx; struct resource *res; - unsigned long hflags; int rc; hpriv = ahci_platform_get_resources(pdev); @@ -474,20 +480,9 @@ static int xgene_ahci_probe(struct platform_device *pdev) /* Configure the host controller */ xgene_ahci_hw_init(hpriv); - /* - * Setup DMA mask. This is preliminary until the DMA range is sorted - * out. - */ - rc = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(64)); - if (rc) { - dev_err(dev, "Unable to set dma mask\n"); - goto disable_resources; - } - - hflags = AHCI_HFLAG_NO_PMP | AHCI_HFLAG_YES_NCQ; + hpriv->flags = AHCI_HFLAG_NO_PMP | AHCI_HFLAG_YES_NCQ; - rc = ahci_platform_init_host(pdev, hpriv, &xgene_ahci_port_info, - hflags, 0, 0); + rc = ahci_platform_init_host(pdev, hpriv, &xgene_ahci_port_info); if (rc) goto disable_resources; diff --git a/drivers/ata/libahci.c b/drivers/ata/libahci.c index d72ce0470309..b784e9de426a 100644 --- a/drivers/ata/libahci.c +++ b/drivers/ata/libahci.c @@ -382,8 +382,6 @@ static ssize_t ahci_show_em_supported(struct device *dev, * ahci_save_initial_config - Save and fixup initial config values * @dev: target AHCI device * @hpriv: host private area to store config values - * @force_port_map: force port map to a specified value - * @mask_port_map: mask out particular bits from port map * * Some registers containing configuration info might be setup by * BIOS and might be cleared on reset. This function saves the @@ -398,10 +396,7 @@ static ssize_t ahci_show_em_supported(struct device *dev, * LOCKING: * None. */ -void ahci_save_initial_config(struct device *dev, - struct ahci_host_priv *hpriv, - unsigned int force_port_map, - unsigned int mask_port_map) +void ahci_save_initial_config(struct device *dev, struct ahci_host_priv *hpriv) { void __iomem *mmio = hpriv->mmio; u32 cap, cap2, vers, port_map; @@ -468,17 +463,17 @@ void ahci_save_initial_config(struct device *dev, cap &= ~HOST_CAP_FBS; } - if (force_port_map && port_map != force_port_map) { + if (hpriv->force_port_map && port_map != hpriv->force_port_map) { dev_info(dev, "forcing port_map 0x%x -> 0x%x\n", - port_map, force_port_map); - port_map = force_port_map; + port_map, hpriv->force_port_map); + port_map = hpriv->force_port_map; } - if (mask_port_map) { + if (hpriv->mask_port_map) { dev_warn(dev, "masking port_map 0x%x -> 0x%x\n", port_map, - port_map & mask_port_map); - port_map &= mask_port_map; + port_map & hpriv->mask_port_map); + port_map &= hpriv->mask_port_map; } /* cross check port_map and cap.n_ports */ diff --git a/drivers/ata/libahci_platform.c b/drivers/ata/libahci_platform.c index b0077589f065..5b92c290e6c6 100644 --- a/drivers/ata/libahci_platform.c +++ b/drivers/ata/libahci_platform.c @@ -39,6 +39,67 @@ static struct scsi_host_template ahci_platform_sht = { }; /** + * ahci_platform_enable_phys - Enable PHYs + * @hpriv: host private area to store config values + * + * This function enables all the PHYs found in hpriv->phys, if any. + * If a PHY fails to be enabled, it disables all the PHYs already + * enabled in reverse order and returns an error. + * + * RETURNS: + * 0 on success otherwise a negative error code + */ +int ahci_platform_enable_phys(struct ahci_host_priv *hpriv) +{ + int rc, i; + + for (i = 0; i < hpriv->nports; i++) { + if (!hpriv->phys[i]) + continue; + + rc = phy_init(hpriv->phys[i]); + if (rc) + goto disable_phys; + + rc = phy_power_on(hpriv->phys[i]); + if (rc) { + phy_exit(hpriv->phys[i]); + goto disable_phys; + } + } + + return 0; + +disable_phys: + while (--i >= 0) { + phy_power_off(hpriv->phys[i]); + phy_exit(hpriv->phys[i]); + } + return rc; +} +EXPORT_SYMBOL_GPL(ahci_platform_enable_phys); + +/** + * ahci_platform_disable_phys - Disable PHYs + * @hpriv: host private area to store config values + * + * This function disables all PHYs found in hpriv->phys. + */ +void ahci_platform_disable_phys(struct ahci_host_priv *hpriv) +{ + int i; + + for (i = 0; i < hpriv->nports; i++) { + if (!hpriv->phys[i]) + continue; + + phy_power_off(hpriv->phys[i]); + phy_exit(hpriv->phys[i]); + } +} +EXPORT_SYMBOL_GPL(ahci_platform_disable_phys); + +/** * ahci_platform_enable_clks - Enable platform clocks * @hpriv: host private area to store config values * @@ -92,7 +153,7 @@ EXPORT_SYMBOL_GPL(ahci_platform_disable_clks); * following order: * 1) Regulator * 2) Clocks (through ahci_platform_enable_clks) - * 3) Phy + * 3) Phys * * If resource enabling fails at any point the previous enabled resources * are disabled in reverse order. @@ -114,17 +175,9 @@ int ahci_platform_enable_resources(struct ahci_host_priv *hpriv) if (rc) goto disable_regulator; - if (hpriv->phy) { - rc = phy_init(hpriv->phy); - if (rc) - goto disable_clks; - - rc = phy_power_on(hpriv->phy); - if (rc) { - phy_exit(hpriv->phy); - goto disable_clks; - } - } + rc = ahci_platform_enable_phys(hpriv); + if (rc) + goto disable_clks; return 0; @@ -144,16 +197,13 @@ EXPORT_SYMBOL_GPL(ahci_platform_enable_resources); * * This function disables all ahci_platform managed resources in the * following order: - * 1) Phy + * 1) Phys * 2) Clocks (through ahci_platform_disable_clks) * 3) Regulator */ void ahci_platform_disable_resources(struct ahci_host_priv *hpriv) { - if (hpriv->phy) { - phy_power_off(hpriv->phy); - phy_exit(hpriv->phy); - } + ahci_platform_disable_phys(hpriv); ahci_platform_disable_clks(hpriv); @@ -187,7 +237,7 @@ static void ahci_platform_put_resources(struct device *dev, void *res) * 2) regulator for controlling the targets power (optional) * 3) 0 - AHCI_MAX_CLKS clocks, as specified in the devs devicetree node, * or for non devicetree enabled platforms a single clock - * 4) phy (optional) + * 4) phys (optional) * * RETURNS: * The allocated ahci_host_priv on success, otherwise an ERR_PTR value @@ -197,7 +247,9 @@ struct ahci_host_priv *ahci_platform_get_resources(struct platform_device *pdev) struct device *dev = &pdev->dev; struct ahci_host_priv *hpriv; struct clk *clk; - int i, rc = -ENOMEM; + struct device_node *child; + int i, enabled_ports = 0, rc = -ENOMEM; + u32 mask_port_map = 0; if (!devres_open_group(dev, NULL, GFP_KERNEL)) return ERR_PTR(-ENOMEM); @@ -246,28 +298,89 @@ struct ahci_host_priv *ahci_platform_get_resources(struct platform_device *pdev) hpriv->clks[i] = clk; } - hpriv->phy = devm_phy_get(dev, "sata-phy"); - if (IS_ERR(hpriv->phy)) { - rc = PTR_ERR(hpriv->phy); - switch (rc) { - case -ENOSYS: - /* No PHY support. Check if PHY is required. */ - if (of_find_property(dev->of_node, "phys", NULL)) { - dev_err(dev, "couldn't get sata-phy: ENOSYS\n"); + hpriv->nports = of_get_child_count(dev->of_node); + + if (hpriv->nports) { + hpriv->phys = devm_kzalloc(dev, + hpriv->nports * sizeof(*hpriv->phys), + GFP_KERNEL); + if (!hpriv->phys) { + rc = -ENOMEM; + goto err_out; + } + + for_each_child_of_node(dev->of_node, child) { + u32 port; + + if (!of_device_is_available(child)) + continue; + + if (of_property_read_u32(child, "reg", &port)) { + rc = -EINVAL; goto err_out; } - case -ENODEV: - /* continue normally */ - hpriv->phy = NULL; - break; - case -EPROBE_DEFER: - goto err_out; + if (port >= hpriv->nports) { + dev_warn(dev, "invalid port number %d\n", port); + continue; + } + + mask_port_map |= BIT(port); - default: - dev_err(dev, "couldn't get sata-phy\n"); + hpriv->phys[port] = devm_of_phy_get(dev, child, NULL); + if (IS_ERR(hpriv->phys[port])) { + rc = PTR_ERR(hpriv->phys[port]); + dev_err(dev, + "couldn't get PHY in node %s: %d\n", + child->name, rc); + goto err_out; + } + + enabled_ports++; + } + if (!enabled_ports) { + dev_warn(dev, "No port enabled\n"); + rc = -ENODEV; goto err_out; } + + if (!hpriv->mask_port_map) + hpriv->mask_port_map = mask_port_map; + } else { + /* + * If no sub-node was found, keep this for device tree + * compatibility + */ + struct phy *phy = devm_phy_get(dev, "sata-phy"); + if (!IS_ERR(phy)) { + hpriv->phys = devm_kzalloc(dev, sizeof(*hpriv->phys), + GFP_KERNEL); + if (!hpriv->phys) { + rc = -ENOMEM; + goto err_out; + } + + hpriv->phys[0] = phy; + hpriv->nports = 1; + } else { + rc = PTR_ERR(phy); + switch (rc) { + case -ENOSYS: + /* No PHY support. Check if PHY is required. */ + if (of_find_property(dev->of_node, "phys", NULL)) { + dev_err(dev, "couldn't get sata-phy: ENOSYS\n"); + goto err_out; + } + case -ENODEV: + /* continue normally */ + hpriv->phys = NULL; + break; + + default: + goto err_out; + + } + } } pm_runtime_enable(dev); @@ -288,12 +401,9 @@ EXPORT_SYMBOL_GPL(ahci_platform_get_resources); * @pdev: platform device pointer for the host * @hpriv: ahci-host private data for the host * @pi_template: template for the ata_port_info to use - * @host_flags: ahci host flags used in ahci_host_priv - * @force_port_map: param passed to ahci_save_initial_config - * @mask_port_map: param passed to ahci_save_initial_config * * This function does all the usual steps needed to bring up an - * ahci-platform host, note any necessary resources (ie clks, phy, etc.) + * ahci-platform host, note any necessary resources (ie clks, phys, etc.) * must be initialized / enabled before calling this. * * RETURNS: @@ -301,10 +411,7 @@ EXPORT_SYMBOL_GPL(ahci_platform_get_resources); */ int ahci_platform_init_host(struct platform_device *pdev, struct ahci_host_priv *hpriv, - const struct ata_port_info *pi_template, - unsigned long host_flags, - unsigned int force_port_map, - unsigned int mask_port_map) + const struct ata_port_info *pi_template) { struct device *dev = &pdev->dev; struct ata_port_info pi = *pi_template; @@ -319,10 +426,9 @@ int ahci_platform_init_host(struct platform_device *pdev, } /* prepare host */ - pi.private_data = (void *)host_flags; - hpriv->flags |= host_flags; + pi.private_data = (void *)(unsigned long)hpriv->flags; - ahci_save_initial_config(dev, hpriv, force_port_map, mask_port_map); + ahci_save_initial_config(dev, hpriv); if (hpriv->cap & HOST_CAP_NCQ) pi.flags |= ATA_FLAG_NCQ; @@ -369,6 +475,19 @@ int ahci_platform_init_host(struct platform_device *pdev, ap->ops = &ata_dummy_port_ops; } + if (hpriv->cap & HOST_CAP_64) { + rc = dma_coerce_mask_and_coherent(dev, DMA_BIT_MASK(64)); + if (rc) { + rc = dma_coerce_mask_and_coherent(dev, + DMA_BIT_MASK(32)); + if (rc) { + dev_err(dev, "Failed to enable 64-bit DMA.\n"); + return rc; + } + dev_warn(dev, "Enable 32-bit DMA instead of 64-bit.\n"); + } + } + rc = ahci_reset_controller(host); if (rc) return rc; @@ -399,7 +518,7 @@ static void ahci_host_stop(struct ata_host *host) * @dev: device pointer for the host * * This function does all the usual steps needed to suspend an - * ahci-platform host, note any necessary resources (ie clks, phy, etc.) + * ahci-platform host, note any necessary resources (ie clks, phys, etc.) * must be disabled after calling this. * * RETURNS: @@ -436,7 +555,7 @@ EXPORT_SYMBOL_GPL(ahci_platform_suspend_host); * @dev: device pointer for the host * * This function does all the usual steps needed to resume an ahci-platform - * host, note any necessary resources (ie clks, phy, etc.) must be + * host, note any necessary resources (ie clks, phys, etc.) must be * initialized / enabled before calling this. * * RETURNS: diff --git a/drivers/ata/pata_samsung_cf.c b/drivers/ata/pata_samsung_cf.c index fb528831fb92..2578fc16960a 100644 --- a/drivers/ata/pata_samsung_cf.c +++ b/drivers/ata/pata_samsung_cf.c @@ -54,7 +54,6 @@ enum s3c_cpu_type { TYPE_S3C64XX, - TYPE_S5PC100, TYPE_S5PV210, }; @@ -476,10 +475,6 @@ static void pata_s3c_hwinit(struct s3c_ide_info *info, writel(0x1b, info->ide_addr + S3C_ATA_IRQ_MSK); break; - case TYPE_S5PC100: - pata_s3c_cfg_mode(info->sfr_addr); - /* FALLTHROUGH */ - case TYPE_S5PV210: /* Configure as little endian */ pata_s3c_set_endian(info->ide_addr, 0); @@ -549,11 +544,6 @@ static int __init pata_s3c_probe(struct platform_device *pdev) info->sfr_addr = info->ide_addr + 0x1800; info->ide_addr += 0x1900; info->fifo_status_reg = 0x94; - } else if (cpu_type == TYPE_S5PC100) { - ap->ops = &pata_s5p_port_ops; - info->sfr_addr = info->ide_addr + 0x1800; - info->ide_addr += 0x1900; - info->fifo_status_reg = 0x84; } else { ap->ops = &pata_s5p_port_ops; info->fifo_status_reg = 0x84; @@ -653,9 +643,6 @@ static struct platform_device_id pata_s3c_driver_ids[] = { .name = "s3c64xx-pata", .driver_data = TYPE_S3C64XX, }, { - .name = "s5pc100-pata", - .driver_data = TYPE_S5PC100, - }, { .name = "s5pv210-pata", .driver_data = TYPE_S5PV210, }, diff --git a/drivers/ata/sata_fsl.c b/drivers/ata/sata_fsl.c index 616a6d2ac20c..07bc7e4dbd04 100644 --- a/drivers/ata/sata_fsl.c +++ b/drivers/ata/sata_fsl.c @@ -734,13 +734,12 @@ static int sata_fsl_port_start(struct ata_port *ap) if (!pp) return -ENOMEM; - mem = dma_alloc_coherent(dev, SATA_FSL_PORT_PRIV_DMA_SZ, &mem_dma, - GFP_KERNEL); + mem = dma_zalloc_coherent(dev, SATA_FSL_PORT_PRIV_DMA_SZ, &mem_dma, + GFP_KERNEL); if (!mem) { kfree(pp); return -ENOMEM; } - memset(mem, 0, SATA_FSL_PORT_PRIV_DMA_SZ); pp->cmdslot = mem; pp->cmdslot_paddr = mem_dma; diff --git a/drivers/ata/sata_highbank.c b/drivers/ata/sata_highbank.c index 65965cf5af06..da3bc2709c63 100644 --- a/drivers/ata/sata_highbank.c +++ b/drivers/ata/sata_highbank.c @@ -512,7 +512,7 @@ static int ahci_highbank_probe(struct platform_device *pdev) return rc; - ahci_save_initial_config(dev, hpriv, 0, 0); + ahci_save_initial_config(dev, hpriv); /* prepare host */ if (hpriv->cap & HOST_CAP_NCQ) diff --git a/drivers/ata/sata_sil24.c b/drivers/ata/sata_sil24.c index 0534890f118a..d81b20ddb527 100644 --- a/drivers/ata/sata_sil24.c +++ b/drivers/ata/sata_sil24.c @@ -1154,8 +1154,8 @@ static irqreturn_t sil24_interrupt(int irq, void *dev_instance) status = readl(host_base + HOST_IRQ_STAT); if (status == 0xffffffff) { - printk(KERN_ERR DRV_NAME ": IRQ status == 0xffffffff, " - "PCI fault or device removal?\n"); + dev_err(host->dev, "IRQ status == 0xffffffff, " + "PCI fault or device removal?\n"); goto out; } diff --git a/include/linux/ahci_platform.h b/include/linux/ahci_platform.h index 6dfd51a04d77..09a947e8bc87 100644 --- a/include/linux/ahci_platform.h +++ b/include/linux/ahci_platform.h @@ -43,10 +43,7 @@ struct ahci_host_priv *ahci_platform_get_resources( struct platform_device *pdev); int ahci_platform_init_host(struct platform_device *pdev, struct ahci_host_priv *hpriv, - const struct ata_port_info *pi_template, - unsigned long host_flags, - unsigned int force_port_map, - unsigned int mask_port_map); + const struct ata_port_info *pi_template); int ahci_platform_suspend_host(struct device *dev); int ahci_platform_resume_host(struct device *dev); diff --git a/include/linux/platform_data/ata-samsung_cf.h b/include/linux/platform_data/ata-samsung_cf.h index c2049e3d7444..748e71642c4a 100644 --- a/include/linux/platform_data/ata-samsung_cf.h +++ b/include/linux/platform_data/ata-samsung_cf.h @@ -29,7 +29,6 @@ extern void s3c_ide_set_platdata(struct s3c_ide_platdata *pdata); /* architecture-specific IDE configuration */ extern void s3c64xx_ide_setup_gpio(void); -extern void s5pc100_ide_setup_gpio(void); extern void s5pv210_ide_setup_gpio(void); #endif /*__ATA_SAMSUNG_CF_H */ |