summaryrefslogtreecommitdiff
path: root/Documentation
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation')
-rw-r--r--Documentation/devicetree/bindings/arm/tegra/emc.txt100
-rw-r--r--Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt19
-rw-r--r--Documentation/devicetree/bindings/dma/tegra20-apbdma.txt30
-rw-r--r--Documentation/devicetree/bindings/gpio/gpio_nvidia.txt36
4 files changed, 183 insertions, 2 deletions
diff --git a/Documentation/devicetree/bindings/arm/tegra/emc.txt b/Documentation/devicetree/bindings/arm/tegra/emc.txt
new file mode 100644
index 000000000000..09335f8eee00
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/tegra/emc.txt
@@ -0,0 +1,100 @@
+Embedded Memory Controller
+
+Properties:
+- name : Should be emc
+- #address-cells : Should be 1
+- #size-cells : Should be 0
+- compatible : Should contain "nvidia,tegra20-emc".
+- reg : Offset and length of the register set for the device
+- nvidia,use-ram-code : If present, the sub-nodes will be addressed
+ and chosen using the ramcode board selector. If omitted, only one
+ set of tables can be present and said tables will be used
+ irrespective of ram-code configuration.
+
+Child device nodes describe the memory settings for different configurations and clock rates.
+
+Example:
+
+ emc@7000f400 {
+ #address-cells = < 1 >;
+ #size-cells = < 0 >;
+ compatible = "nvidia,tegra20-emc";
+ reg = <0x7000f4000 0x200>;
+ }
+
+
+Embedded Memory Controller ram-code table
+
+If the emc node has the nvidia,use-ram-code property present, then the
+next level of nodes below the emc table are used to specify which settings
+apply for which ram-code settings.
+
+If the emc node lacks the nvidia,use-ram-code property, this level is omitted
+and the tables are stored directly under the emc node (see below).
+
+Properties:
+
+- name : Should be emc-tables
+- nvidia,ram-code : the binary representation of the ram-code board strappings
+ for which this node (and children) are valid.
+
+
+
+Embedded Memory Controller configuration table
+
+This is a table containing the EMC register settings for the various
+operating speeds of the memory controller. They are always located as
+subnodes of the emc controller node.
+
+There are two ways of specifying which tables to use:
+
+* The simplest is if there is just one set of tables in the device tree,
+ and they will always be used (based on which frequency is used).
+ This is the preferred method, especially when firmware can fill in
+ this information based on the specific system information and just
+ pass it on to the kernel.
+
+* The slightly more complex one is when more than one memory configuration
+ might exist on the system. The Tegra20 platform handles this during
+ early boot by selecting one out of possible 4 memory settings based
+ on a 2-pin "ram code" bootstrap setting on the board. The values of
+ these strappings can be read through a register in the SoC, and thus
+ used to select which tables to use.
+
+Properties:
+- name : Should be emc-table
+- compatible : Should contain "nvidia,tegra20-emc-table".
+- reg : either an opaque enumerator to tell different tables apart, or
+ the valid frequency for which the table should be used (in kHz).
+- clock-frequency : the clock frequency for the EMC at which this
+ table should be used (in kHz).
+- nvidia,emc-registers : a 46 word array of EMC registers to be programmed
+ for operation at the 'clock-frequency' setting.
+ The order and contents of the registers are:
+ RC, RFC, RAS, RP, R2W, W2R, R2P, W2P, RD_RCD, WR_RCD, RRD, REXT,
+ WDV, QUSE, QRST, QSAFE, RDV, REFRESH, BURST_REFRESH_NUM, PDEX2WR,
+ PDEX2RD, PCHG2PDEN, ACT2PDEN, AR2PDEN, RW2PDEN, TXSR, TCKE, TFAW,
+ TRPAB, TCLKSTABLE, TCLKSTOP, TREFBW, QUSE_EXTRA, FBIO_CFG6, ODT_WRITE,
+ ODT_READ, FBIO_CFG5, CFG_DIG_DLL, DLL_XFORM_DQS, DLL_XFORM_QUSE,
+ ZCAL_REF_CNT, ZCAL_WAIT_CNT, AUTO_CAL_INTERVAL, CFG_CLKTRIM_0,
+ CFG_CLKTRIM_1, CFG_CLKTRIM_2
+
+ emc-table@166000 {
+ reg = <166000>;
+ compatible = "nvidia,tegra20-emc-table";
+ clock-frequency = < 166000 >;
+ nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 >;
+ };
+
+ emc-table@333000 {
+ reg = <333000>;
+ compatible = "nvidia,tegra20-emc-table";
+ clock-frequency = < 333000 >;
+ nvidia,emc-registers = < 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 0 0 0 0 0 0 0 0 0 0
+ 0 0 0 0 >;
+ };
diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
new file mode 100644
index 000000000000..b5846e21cc2e
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
@@ -0,0 +1,19 @@
+NVIDIA Tegra Power Management Controller (PMC)
+
+Properties:
+- name : Should be pmc
+- compatible : Should contain "nvidia,tegra<chip>-pmc".
+- reg : Offset and length of the register set for the device
+- nvidia,invert-interrupt : If present, inverts the PMU interrupt signal.
+ The PMU is an external Power Management Unit, whose interrupt output
+ signal is fed into the PMC. This signal is optionally inverted, and then
+ fed into the ARM GIC. The PMC is not involved in the detection or
+ handling of this interrupt signal, merely its inversion.
+
+Example:
+
+pmc@7000f400 {
+ compatible = "nvidia,tegra20-pmc";
+ reg = <0x7000e400 0x400>;
+ nvidia,invert-interrupt;
+};
diff --git a/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt b/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt
new file mode 100644
index 000000000000..90fa7da525b8
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/tegra20-apbdma.txt
@@ -0,0 +1,30 @@
+* NVIDIA Tegra APB DMA controller
+
+Required properties:
+- compatible: Should be "nvidia,<chip>-apbdma"
+- reg: Should contain DMA registers location and length. This shuld include
+ all of the per-channel registers.
+- interrupts: Should contain all of the per-channel DMA interrupts.
+
+Examples:
+
+apbdma: dma@6000a000 {
+ compatible = "nvidia,tegra20-apbdma";
+ reg = <0x6000a000 0x1200>;
+ interrupts = < 0 136 0x04
+ 0 137 0x04
+ 0 138 0x04
+ 0 139 0x04
+ 0 140 0x04
+ 0 141 0x04
+ 0 142 0x04
+ 0 143 0x04
+ 0 144 0x04
+ 0 145 0x04
+ 0 146 0x04
+ 0 147 0x04
+ 0 148 0x04
+ 0 149 0x04
+ 0 150 0x04
+ 0 151 0x04 >;
+};
diff --git a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt b/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt
index eb4b530d64e1..023c9526e5f8 100644
--- a/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio_nvidia.txt
@@ -1,8 +1,40 @@
-NVIDIA Tegra 2 GPIO controller
+NVIDIA Tegra GPIO controller
Required properties:
-- compatible : "nvidia,tegra20-gpio"
+- compatible : "nvidia,tegra<chip>-gpio"
+- reg : Physical base address and length of the controller's registers.
+- interrupts : The interrupt outputs from the controller. For Tegra20,
+ there should be 7 interrupts specified, and for Tegra30, there should
+ be 8 interrupts specified.
- #gpio-cells : Should be two. The first cell is the pin number and the
second cell is used to specify optional parameters:
- bit 0 specifies polarity (0 for normal, 1 for inverted)
- gpio-controller : Marks the device node as a GPIO controller.
+- #interrupt-cells : Should be 2.
+ The first cell is the GPIO number.
+ The second cell is used to specify flags:
+ bits[3:0] trigger type and level flags:
+ 1 = low-to-high edge triggered.
+ 2 = high-to-low edge triggered.
+ 4 = active high level-sensitive.
+ 8 = active low level-sensitive.
+ Valid combinations are 1, 2, 3, 4, 8.
+- interrupt-controller : Marks the device node as an interrupt controller.
+
+Example:
+
+gpio: gpio@6000d000 {
+ compatible = "nvidia,tegra20-gpio";
+ reg = < 0x6000d000 0x1000 >;
+ interrupts = < 0 32 0x04
+ 0 33 0x04
+ 0 34 0x04
+ 0 35 0x04
+ 0 55 0x04
+ 0 87 0x04
+ 0 89 0x04 >;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+};