summaryrefslogtreecommitdiff
path: root/drivers
diff options
context:
space:
mode:
Diffstat (limited to 'drivers')
-rw-r--r--drivers/clocksource/tcb_clksrc.c90
-rw-r--r--drivers/i2c/busses/i2c-pxa.c95
-rw-r--r--drivers/misc/atmel_tclib.c64
-rw-r--r--drivers/pcmcia/at91_cf.c5
-rw-r--r--drivers/rtc/rtc-at91sam9.c85
-rw-r--r--drivers/tty/serial/atmel_serial.c2
-rw-r--r--drivers/tty/serial/pxa.c49
-rw-r--r--drivers/usb/gadget/at91_udc.c9
-rw-r--r--drivers/usb/gadget/atmel_usba_udc.c6
-rw-r--r--drivers/usb/host/ohci-at91.c5
-rw-r--r--drivers/watchdog/at91rm9200_wdt.c8
11 files changed, 275 insertions, 143 deletions
diff --git a/drivers/clocksource/tcb_clksrc.c b/drivers/clocksource/tcb_clksrc.c
index 55d0f95f82f9..32cb929b8eb6 100644
--- a/drivers/clocksource/tcb_clksrc.c
+++ b/drivers/clocksource/tcb_clksrc.c
@@ -19,6 +19,8 @@
* - Two channels combine to create a free-running 32 bit counter
* with a base rate of 5+ MHz, packaged as a clocksource (with
* resolution better than 200 nsec).
+ * - Some chips support 32 bit counter. A single channel is used for
+ * this 32 bit free-running counter. the second channel is not used.
*
* - The third channel may be used to provide a 16-bit clockevent
* source, used in either periodic or oneshot mode. This runs
@@ -54,6 +56,11 @@ static cycle_t tc_get_cycles(struct clocksource *cs)
return (upper << 16) | lower;
}
+static cycle_t tc_get_cycles32(struct clocksource *cs)
+{
+ return __raw_readl(tcaddr + ATMEL_TC_REG(0, CV));
+}
+
static struct clocksource clksrc = {
.name = "tcb_clksrc",
.rating = 200,
@@ -209,6 +216,48 @@ static void __init setup_clkevents(struct atmel_tc *tc, int clk32k_divisor_idx)
#endif
+static void __init tcb_setup_dual_chan(struct atmel_tc *tc, int mck_divisor_idx)
+{
+ /* channel 0: waveform mode, input mclk/8, clock TIOA0 on overflow */
+ __raw_writel(mck_divisor_idx /* likely divide-by-8 */
+ | ATMEL_TC_WAVE
+ | ATMEL_TC_WAVESEL_UP /* free-run */
+ | ATMEL_TC_ACPA_SET /* TIOA0 rises at 0 */
+ | ATMEL_TC_ACPC_CLEAR, /* (duty cycle 50%) */
+ tcaddr + ATMEL_TC_REG(0, CMR));
+ __raw_writel(0x0000, tcaddr + ATMEL_TC_REG(0, RA));
+ __raw_writel(0x8000, tcaddr + ATMEL_TC_REG(0, RC));
+ __raw_writel(0xff, tcaddr + ATMEL_TC_REG(0, IDR)); /* no irqs */
+ __raw_writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(0, CCR));
+
+ /* channel 1: waveform mode, input TIOA0 */
+ __raw_writel(ATMEL_TC_XC1 /* input: TIOA0 */
+ | ATMEL_TC_WAVE
+ | ATMEL_TC_WAVESEL_UP, /* free-run */
+ tcaddr + ATMEL_TC_REG(1, CMR));
+ __raw_writel(0xff, tcaddr + ATMEL_TC_REG(1, IDR)); /* no irqs */
+ __raw_writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(1, CCR));
+
+ /* chain channel 0 to channel 1*/
+ __raw_writel(ATMEL_TC_TC1XC1S_TIOA0, tcaddr + ATMEL_TC_BMR);
+ /* then reset all the timers */
+ __raw_writel(ATMEL_TC_SYNC, tcaddr + ATMEL_TC_BCR);
+}
+
+static void __init tcb_setup_single_chan(struct atmel_tc *tc, int mck_divisor_idx)
+{
+ /* channel 0: waveform mode, input mclk/8 */
+ __raw_writel(mck_divisor_idx /* likely divide-by-8 */
+ | ATMEL_TC_WAVE
+ | ATMEL_TC_WAVESEL_UP, /* free-run */
+ tcaddr + ATMEL_TC_REG(0, CMR));
+ __raw_writel(0xff, tcaddr + ATMEL_TC_REG(0, IDR)); /* no irqs */
+ __raw_writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(0, CCR));
+
+ /* then reset all the timers */
+ __raw_writel(ATMEL_TC_SYNC, tcaddr + ATMEL_TC_BCR);
+}
+
static int __init tcb_clksrc_init(void)
{
static char bootinfo[] __initdata
@@ -260,34 +309,19 @@ static int __init tcb_clksrc_init(void)
divided_rate / 1000000,
((divided_rate + 500000) % 1000000) / 1000);
- /* tclib will give us three clocks no matter what the
- * underlying platform supports.
- */
- clk_enable(tc->clk[1]);
-
- /* channel 0: waveform mode, input mclk/8, clock TIOA0 on overflow */
- __raw_writel(best_divisor_idx /* likely divide-by-8 */
- | ATMEL_TC_WAVE
- | ATMEL_TC_WAVESEL_UP /* free-run */
- | ATMEL_TC_ACPA_SET /* TIOA0 rises at 0 */
- | ATMEL_TC_ACPC_CLEAR, /* (duty cycle 50%) */
- tcaddr + ATMEL_TC_REG(0, CMR));
- __raw_writel(0x0000, tcaddr + ATMEL_TC_REG(0, RA));
- __raw_writel(0x8000, tcaddr + ATMEL_TC_REG(0, RC));
- __raw_writel(0xff, tcaddr + ATMEL_TC_REG(0, IDR)); /* no irqs */
- __raw_writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(0, CCR));
-
- /* channel 1: waveform mode, input TIOA0 */
- __raw_writel(ATMEL_TC_XC1 /* input: TIOA0 */
- | ATMEL_TC_WAVE
- | ATMEL_TC_WAVESEL_UP, /* free-run */
- tcaddr + ATMEL_TC_REG(1, CMR));
- __raw_writel(0xff, tcaddr + ATMEL_TC_REG(1, IDR)); /* no irqs */
- __raw_writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(1, CCR));
-
- /* chain channel 0 to channel 1, then reset all the timers */
- __raw_writel(ATMEL_TC_TC1XC1S_TIOA0, tcaddr + ATMEL_TC_BMR);
- __raw_writel(ATMEL_TC_SYNC, tcaddr + ATMEL_TC_BCR);
+ if (tc->tcb_config && tc->tcb_config->counter_width == 32) {
+ /* use apropriate function to read 32 bit counter */
+ clksrc.read = tc_get_cycles32;
+ /* setup ony channel 0 */
+ tcb_setup_single_chan(tc, best_divisor_idx);
+ } else {
+ /* tclib will give us three clocks no matter what the
+ * underlying platform supports.
+ */
+ clk_enable(tc->clk[1]);
+ /* setup both channel 0 & 1 */
+ tcb_setup_dual_chan(tc, best_divisor_idx);
+ }
/* and away we go! */
clocksource_register_hz(&clksrc, divided_rate);
diff --git a/drivers/i2c/busses/i2c-pxa.c b/drivers/i2c/busses/i2c-pxa.c
index d60364650990..f6733267fa9c 100644
--- a/drivers/i2c/busses/i2c-pxa.c
+++ b/drivers/i2c/busses/i2c-pxa.c
@@ -29,6 +29,8 @@
#include <linux/errno.h>
#include <linux/interrupt.h>
#include <linux/i2c-pxa.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
#include <linux/of_i2c.h>
#include <linux/platform_device.h>
#include <linux/err.h>
@@ -1044,23 +1046,60 @@ static const struct i2c_algorithm i2c_pxa_pio_algorithm = {
.functionality = i2c_pxa_functionality,
};
-static int i2c_pxa_probe(struct platform_device *dev)
+static struct of_device_id i2c_pxa_dt_ids[] = {
+ { .compatible = "mrvl,pxa-i2c", .data = (void *)REGS_PXA2XX },
+ { .compatible = "mrvl,pwri2c", .data = (void *)REGS_PXA3XX },
+ { .compatible = "mrvl,mmp-twsi", .data = (void *)REGS_PXA2XX },
+ {}
+};
+MODULE_DEVICE_TABLE(of, i2c_pxa_dt_ids);
+
+static int i2c_pxa_probe_dt(struct platform_device *pdev, struct pxa_i2c *i2c,
+ enum pxa_i2c_types *i2c_types)
{
- struct pxa_i2c *i2c;
- struct resource *res;
- struct i2c_pxa_platform_data *plat = dev->dev.platform_data;
- const struct platform_device_id *id = platform_get_device_id(dev);
- enum pxa_i2c_types i2c_type = id->driver_data;
+ struct device_node *np = pdev->dev.of_node;
+ const struct of_device_id *of_id =
+ of_match_device(i2c_pxa_dt_ids, &pdev->dev);
int ret;
- int irq;
- res = platform_get_resource(dev, IORESOURCE_MEM, 0);
- irq = platform_get_irq(dev, 0);
- if (res == NULL || irq < 0)
- return -ENODEV;
+ if (!of_id)
+ return 1;
+ ret = of_alias_get_id(np, "i2c");
+ if (ret < 0) {
+ dev_err(&pdev->dev, "failed to get alias id, errno %d\n", ret);
+ return ret;
+ }
+ pdev->id = ret;
+ if (of_get_property(np, "mrvl,i2c-polling", NULL))
+ i2c->use_pio = 1;
+ if (of_get_property(np, "mrvl,i2c-fast-mode", NULL))
+ i2c->fast_mode = 1;
+ *i2c_types = (u32)(of_id->data);
+ return 0;
+}
- if (!request_mem_region(res->start, resource_size(res), res->name))
- return -ENOMEM;
+static int i2c_pxa_probe_pdata(struct platform_device *pdev,
+ struct pxa_i2c *i2c,
+ enum pxa_i2c_types *i2c_types)
+{
+ struct i2c_pxa_platform_data *plat = pdev->dev.platform_data;
+ const struct platform_device_id *id = platform_get_device_id(pdev);
+
+ *i2c_types = id->driver_data;
+ if (plat) {
+ i2c->use_pio = plat->use_pio;
+ i2c->fast_mode = plat->fast_mode;
+ }
+ return 0;
+}
+
+static int i2c_pxa_probe(struct platform_device *dev)
+{
+ struct i2c_pxa_platform_data *plat = dev->dev.platform_data;
+ enum pxa_i2c_types i2c_type;
+ struct pxa_i2c *i2c;
+ struct resource *res = NULL;
+ int ret, irq;
i2c = kzalloc(sizeof(struct pxa_i2c), GFP_KERNEL);
if (!i2c) {
@@ -1068,6 +1107,24 @@ static int i2c_pxa_probe(struct platform_device *dev)
goto emalloc;
}
+ ret = i2c_pxa_probe_dt(dev, i2c, &i2c_type);
+ if (ret > 0)
+ ret = i2c_pxa_probe_pdata(dev, i2c, &i2c_type);
+ if (ret < 0)
+ goto eclk;
+
+ res = platform_get_resource(dev, IORESOURCE_MEM, 0);
+ irq = platform_get_irq(dev, 0);
+ if (res == NULL || irq < 0) {
+ ret = -ENODEV;
+ goto eclk;
+ }
+
+ if (!request_mem_region(res->start, resource_size(res), res->name)) {
+ ret = -ENOMEM;
+ goto eclk;
+ }
+
i2c->adap.owner = THIS_MODULE;
i2c->adap.retries = 5;
@@ -1109,21 +1166,16 @@ static int i2c_pxa_probe(struct platform_device *dev)
i2c->slave_addr = I2C_PXA_SLAVE_ADDR;
-#ifdef CONFIG_I2C_PXA_SLAVE
if (plat) {
+#ifdef CONFIG_I2C_PXA_SLAVE
i2c->slave_addr = plat->slave_addr;
i2c->slave = plat->slave;
- }
#endif
-
- clk_enable(i2c->clk);
-
- if (plat) {
i2c->adap.class = plat->class;
- i2c->use_pio = plat->use_pio;
- i2c->fast_mode = plat->fast_mode;
}
+ clk_enable(i2c->clk);
+
if (i2c->use_pio) {
i2c->adap.algo = &i2c_pxa_pio_algorithm;
} else {
@@ -1234,6 +1286,7 @@ static struct platform_driver i2c_pxa_driver = {
.name = "pxa2xx-i2c",
.owner = THIS_MODULE,
.pm = I2C_PXA_DEV_PM_OPS,
+ .of_match_table = i2c_pxa_dt_ids,
},
.id_table = i2c_pxa_id_table,
};
diff --git a/drivers/misc/atmel_tclib.c b/drivers/misc/atmel_tclib.c
index 4bcfc3759734..c8d8e38d0d8a 100644
--- a/drivers/misc/atmel_tclib.c
+++ b/drivers/misc/atmel_tclib.c
@@ -6,12 +6,10 @@
#include <linux/ioport.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
+#include <linux/module.h>
#include <linux/slab.h>
#include <linux/export.h>
-
-/* Number of bytes to reserve for the iomem resource */
-#define ATMEL_TC_IOMEM_SIZE 256
-
+#include <linux/of.h>
/*
* This is a thin library to solve the problem of how to portably allocate
@@ -48,10 +46,17 @@ struct atmel_tc *atmel_tc_alloc(unsigned block, const char *name)
struct atmel_tc *tc;
struct platform_device *pdev = NULL;
struct resource *r;
+ size_t size;
spin_lock(&tc_list_lock);
list_for_each_entry(tc, &tc_list, node) {
- if (tc->pdev->id == block) {
+ if (tc->pdev->dev.of_node) {
+ if (of_alias_get_id(tc->pdev->dev.of_node, "tcb")
+ == block) {
+ pdev = tc->pdev;
+ break;
+ }
+ } else if (tc->pdev->id == block) {
pdev = tc->pdev;
break;
}
@@ -61,11 +66,15 @@ struct atmel_tc *atmel_tc_alloc(unsigned block, const char *name)
goto fail;
r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- r = request_mem_region(r->start, ATMEL_TC_IOMEM_SIZE, name);
if (!r)
goto fail;
- tc->regs = ioremap(r->start, ATMEL_TC_IOMEM_SIZE);
+ size = resource_size(r);
+ r = request_mem_region(r->start, size, name);
+ if (!r)
+ goto fail;
+
+ tc->regs = ioremap(r->start, size);
if (!tc->regs)
goto fail_ioremap;
@@ -76,7 +85,7 @@ out:
return tc;
fail_ioremap:
- release_mem_region(r->start, ATMEL_TC_IOMEM_SIZE);
+ release_mem_region(r->start, size);
fail:
tc = NULL;
goto out;
@@ -96,7 +105,7 @@ void atmel_tc_free(struct atmel_tc *tc)
spin_lock(&tc_list_lock);
if (tc->regs) {
iounmap(tc->regs);
- release_mem_region(tc->iomem->start, ATMEL_TC_IOMEM_SIZE);
+ release_mem_region(tc->iomem->start, resource_size(tc->iomem));
tc->regs = NULL;
tc->iomem = NULL;
}
@@ -104,6 +113,30 @@ void atmel_tc_free(struct atmel_tc *tc)
}
EXPORT_SYMBOL_GPL(atmel_tc_free);
+#if defined(CONFIG_OF)
+static struct atmel_tcb_config tcb_rm9200_config = {
+ .counter_width = 16,
+};
+
+static struct atmel_tcb_config tcb_sam9x5_config = {
+ .counter_width = 32,
+};
+
+static const struct of_device_id atmel_tcb_dt_ids[] = {
+ {
+ .compatible = "atmel,at91rm9200-tcb",
+ .data = &tcb_rm9200_config,
+ }, {
+ .compatible = "atmel,at91sam9x5-tcb",
+ .data = &tcb_sam9x5_config,
+ }, {
+ /* sentinel */
+ }
+};
+
+MODULE_DEVICE_TABLE(of, atmel_tcb_dt_ids);
+#endif
+
static int __init tc_probe(struct platform_device *pdev)
{
struct atmel_tc *tc;
@@ -129,6 +162,14 @@ static int __init tc_probe(struct platform_device *pdev)
return -EINVAL;
}
+ /* Now take SoC information if available */
+ if (pdev->dev.of_node) {
+ const struct of_device_id *match;
+ match = of_match_node(atmel_tcb_dt_ids, pdev->dev.of_node);
+ if (match)
+ tc->tcb_config = match->data;
+ }
+
tc->clk[0] = clk;
tc->clk[1] = clk_get(&pdev->dev, "t1_clk");
if (IS_ERR(tc->clk[1]))
@@ -153,7 +194,10 @@ static int __init tc_probe(struct platform_device *pdev)
}
static struct platform_driver tc_driver = {
- .driver.name = "atmel_tcb",
+ .driver = {
+ .name = "atmel_tcb",
+ .of_match_table = of_match_ptr(atmel_tcb_dt_ids),
+ },
};
static int __init tc_init(void)
diff --git a/drivers/pcmcia/at91_cf.c b/drivers/pcmcia/at91_cf.c
index 4902206f53d9..1dd68f502634 100644
--- a/drivers/pcmcia/at91_cf.c
+++ b/drivers/pcmcia/at91_cf.c
@@ -26,6 +26,7 @@
#include <mach/board.h>
#include <mach/at91rm9200_mc.h>
+#include <mach/at91_ramc.h>
/*
@@ -156,7 +157,7 @@ static int at91_cf_set_io_map(struct pcmcia_socket *s, struct pccard_io_map *io)
/*
* Use 16 bit accesses unless/until we need 8-bit i/o space.
*/
- csr = at91_sys_read(AT91_SMC_CSR(cf->board->chipselect)) & ~AT91_SMC_DBW;
+ csr = at91_ramc_read(0, AT91_SMC_CSR(cf->board->chipselect)) & ~AT91_SMC_DBW;
/*
* NOTE: this CF controller ignores IOIS16, so we can't really do
@@ -175,7 +176,7 @@ static int at91_cf_set_io_map(struct pcmcia_socket *s, struct pccard_io_map *io)
csr |= AT91_SMC_DBW_16;
pr_debug("%s: 16bit i/o bus\n", driver_name);
}
- at91_sys_write(AT91_SMC_CSR(cf->board->chipselect), csr);
+ at91_ramc_write(0, AT91_SMC_CSR(cf->board->chipselect), csr);
io->start = cf->socket.io_offset;
io->stop = io->start + SZ_2K - 1;
diff --git a/drivers/rtc/rtc-at91sam9.c b/drivers/rtc/rtc-at91sam9.c
index 274a0aafe42b..831868904e02 100644
--- a/drivers/rtc/rtc-at91sam9.c
+++ b/drivers/rtc/rtc-at91sam9.c
@@ -57,6 +57,7 @@ struct sam9_rtc {
void __iomem *rtt;
struct rtc_device *rtcdev;
u32 imr;
+ void __iomem *gpbr;
};
#define rtt_readl(rtc, field) \
@@ -65,9 +66,9 @@ struct sam9_rtc {
__raw_writel((val), (rtc)->rtt + AT91_RTT_ ## field)
#define gpbr_readl(rtc) \
- at91_sys_read(AT91_GPBR + 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR)
+ __raw_readl((rtc)->gpbr)
#define gpbr_writel(rtc, val) \
- at91_sys_write(AT91_GPBR + 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR, (val))
+ __raw_writel((val), (rtc)->gpbr)
/*
* Read current time and date in RTC
@@ -287,16 +288,19 @@ static const struct rtc_class_ops at91_rtc_ops = {
/*
* Initialize and install RTC driver
*/
-static int __init at91_rtc_probe(struct platform_device *pdev)
+static int __devinit at91_rtc_probe(struct platform_device *pdev)
{
- struct resource *r;
+ struct resource *r, *r_gpbr;
struct sam9_rtc *rtc;
int ret;
u32 mr;
r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!r)
+ r_gpbr = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ if (!r || !r_gpbr) {
+ dev_err(&pdev->dev, "need 2 ressources\n");
return -ENODEV;
+ }
rtc = kzalloc(sizeof *rtc, GFP_KERNEL);
if (!rtc)
@@ -314,6 +318,13 @@ static int __init at91_rtc_probe(struct platform_device *pdev)
goto fail;
}
+ rtc->gpbr = ioremap(r_gpbr->start, resource_size(r_gpbr));
+ if (!rtc->gpbr) {
+ dev_err(&pdev->dev, "failed to map gpbr registers, aborting.\n");
+ ret = -ENOMEM;
+ goto fail_gpbr;
+ }
+
mr = rtt_readl(rtc, MR);
/* unless RTT is counting at 1 Hz, re-initialize it */
@@ -340,7 +351,7 @@ static int __init at91_rtc_probe(struct platform_device *pdev)
if (ret) {
dev_dbg(&pdev->dev, "can't share IRQ %d?\n", AT91_ID_SYS);
rtc_device_unregister(rtc->rtcdev);
- goto fail;
+ goto fail_register;
}
/* NOTE: sam9260 rev A silicon has a ROM bug which resets the
@@ -356,6 +367,8 @@ static int __init at91_rtc_probe(struct platform_device *pdev)
return 0;
fail_register:
+ iounmap(rtc->gpbr);
+fail_gpbr:
iounmap(rtc->rtt);
fail:
platform_set_drvdata(pdev, NULL);
@@ -366,7 +379,7 @@ fail:
/*
* Disable and remove the RTC driver
*/
-static int __exit at91_rtc_remove(struct platform_device *pdev)
+static int __devexit at91_rtc_remove(struct platform_device *pdev)
{
struct sam9_rtc *rtc = platform_get_drvdata(pdev);
u32 mr = rtt_readl(rtc, MR);
@@ -377,6 +390,7 @@ static int __exit at91_rtc_remove(struct platform_device *pdev)
rtc_device_unregister(rtc->rtcdev);
+ iounmap(rtc->gpbr);
iounmap(rtc->rtt);
platform_set_drvdata(pdev, NULL);
kfree(rtc);
@@ -440,63 +454,20 @@ static int at91_rtc_resume(struct platform_device *pdev)
#endif
static struct platform_driver at91_rtc_driver = {
- .driver.name = "rtc-at91sam9",
- .driver.owner = THIS_MODULE,
- .remove = __exit_p(at91_rtc_remove),
+ .probe = at91_rtc_probe,
+ .remove = __devexit_p(at91_rtc_remove),
.shutdown = at91_rtc_shutdown,
.suspend = at91_rtc_suspend,
.resume = at91_rtc_resume,
+ .driver = {
+ .name = "rtc-at91sam9",
+ .owner = THIS_MODULE,
+ },
};
-/* Chips can have more than one RTT module, and they can be used for more
- * than just RTCs. So we can't just register as "the" RTT driver.
- *
- * A normal approach in such cases is to create a library to allocate and
- * free the modules. Here we just use bus_find_device() as like such a
- * library, binding directly ... no runtime "library" footprint is needed.
- */
-static int __init at91_rtc_match(struct device *dev, void *v)
-{
- struct platform_device *pdev = to_platform_device(dev);
- int ret;
-
- /* continue searching if this isn't the RTT we need */
- if (strcmp("at91_rtt", pdev->name) != 0
- || pdev->id != CONFIG_RTC_DRV_AT91SAM9_RTT)
- goto fail;
-
- /* else we found it ... but fail unless we can bind to the RTC driver */
- if (dev->driver) {
- dev_dbg(dev, "busy, can't use as RTC!\n");
- goto fail;
- }
- dev->driver = &at91_rtc_driver.driver;
- if (device_attach(dev) == 0) {
- dev_dbg(dev, "can't attach RTC!\n");
- goto fail;
- }
- ret = at91_rtc_probe(pdev);
- if (ret == 0)
- return true;
-
- dev_dbg(dev, "RTC probe err %d!\n", ret);
-fail:
- return false;
-}
-
static int __init at91_rtc_init(void)
{
- int status;
- struct device *rtc;
-
- status = platform_driver_register(&at91_rtc_driver);
- if (status)
- return status;
- rtc = bus_find_device(&platform_bus_type, NULL,
- NULL, at91_rtc_match);
- if (!rtc)
- platform_driver_unregister(&at91_rtc_driver);
- return rtc ? 0 : -ENODEV;
+ return platform_driver_register(&at91_rtc_driver);
}
module_init(at91_rtc_init);
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 10605ecc99ab..f9a6be7a9bed 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -1526,6 +1526,8 @@ void __init atmel_register_uart_fns(struct atmel_port_fns *fns)
atmel_pops.set_wake = fns->set_wake;
}
+struct platform_device *atmel_default_console_device; /* the serial console device */
+
#ifdef CONFIG_SERIAL_ATMEL_CONSOLE
static void atmel_console_putchar(struct uart_port *port, int ch)
{
diff --git a/drivers/tty/serial/pxa.c b/drivers/tty/serial/pxa.c
index e2fd3d8e0ab4..5847a4b855f7 100644
--- a/drivers/tty/serial/pxa.c
+++ b/drivers/tty/serial/pxa.c
@@ -36,6 +36,7 @@
#include <linux/circ_buf.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
+#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
@@ -44,6 +45,8 @@
#include <linux/io.h>
#include <linux/slab.h>
+#define PXA_NAME_LEN 8
+
struct uart_pxa_port {
struct uart_port port;
unsigned char ier;
@@ -51,7 +54,7 @@ struct uart_pxa_port {
unsigned char mcr;
unsigned int lsr_break_flag;
struct clk *clk;
- char *name;
+ char name[PXA_NAME_LEN];
};
static inline unsigned int serial_in(struct uart_pxa_port *up, int offset)
@@ -781,6 +784,31 @@ static const struct dev_pm_ops serial_pxa_pm_ops = {
};
#endif
+static struct of_device_id serial_pxa_dt_ids[] = {
+ { .compatible = "mrvl,pxa-uart", },
+ { .compatible = "mrvl,mmp-uart", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, serial_pxa_dt_ids);
+
+static int serial_pxa_probe_dt(struct platform_device *pdev,
+ struct uart_pxa_port *sport)
+{
+ struct device_node *np = pdev->dev.of_node;
+ int ret;
+
+ if (!np)
+ return 1;
+
+ ret = of_alias_get_id(np, "serial");
+ if (ret < 0) {
+ dev_err(&pdev->dev, "failed to get alias id, errno %d\n", ret);
+ return ret;
+ }
+ sport->port.line = ret;
+ return 0;
+}
+
static int serial_pxa_probe(struct platform_device *dev)
{
struct uart_pxa_port *sport;
@@ -808,20 +836,16 @@ static int serial_pxa_probe(struct platform_device *dev)
sport->port.irq = irqres->start;
sport->port.fifosize = 64;
sport->port.ops = &serial_pxa_pops;
- sport->port.line = dev->id;
sport->port.dev = &dev->dev;
sport->port.flags = UPF_IOREMAP | UPF_BOOT_AUTOCONF;
sport->port.uartclk = clk_get_rate(sport->clk);
- switch (dev->id) {
- case 0: sport->name = "FFUART"; break;
- case 1: sport->name = "BTUART"; break;
- case 2: sport->name = "STUART"; break;
- case 3: sport->name = "HWUART"; break;
- default:
- sport->name = "???";
- break;
- }
+ ret = serial_pxa_probe_dt(dev, sport);
+ if (ret > 0)
+ sport->port.line = dev->id;
+ else if (ret < 0)
+ goto err_clk;
+ snprintf(sport->name, PXA_NAME_LEN - 1, "UART%d", sport->port.line + 1);
sport->port.membase = ioremap(mmres->start, resource_size(mmres));
if (!sport->port.membase) {
@@ -829,7 +853,7 @@ static int serial_pxa_probe(struct platform_device *dev)
goto err_clk;
}
- serial_pxa_ports[dev->id] = sport;
+ serial_pxa_ports[sport->port.line] = sport;
uart_add_one_port(&serial_pxa_reg, &sport->port);
platform_set_drvdata(dev, sport);
@@ -866,6 +890,7 @@ static struct platform_driver serial_pxa_driver = {
#ifdef CONFIG_PM
.pm = &serial_pxa_pm_ops,
#endif
+ .of_match_table = serial_pxa_dt_ids,
},
};
diff --git a/drivers/usb/gadget/at91_udc.c b/drivers/usb/gadget/at91_udc.c
index 15a8cdb2ded5..2db5f68f7960 100644
--- a/drivers/usb/gadget/at91_udc.c
+++ b/drivers/usb/gadget/at91_udc.c
@@ -40,6 +40,7 @@
#include <mach/board.h>
#include <mach/cpu.h>
#include <mach/at91sam9261_matrix.h>
+#include <mach/at91_matrix.h>
#include "at91_udc.h"
@@ -910,9 +911,9 @@ static void pullup(struct at91_udc *udc, int is_on)
} else if (cpu_is_at91sam9261() || cpu_is_at91sam9g10()) {
u32 usbpucr;
- usbpucr = at91_sys_read(AT91_MATRIX_USBPUCR);
+ usbpucr = at91_matrix_read(AT91_MATRIX_USBPUCR);
usbpucr |= AT91_MATRIX_USBPUCR_PUON;
- at91_sys_write(AT91_MATRIX_USBPUCR, usbpucr);
+ at91_matrix_write(AT91_MATRIX_USBPUCR, usbpucr);
}
} else {
stop_activity(udc);
@@ -928,9 +929,9 @@ static void pullup(struct at91_udc *udc, int is_on)
} else if (cpu_is_at91sam9261() || cpu_is_at91sam9g10()) {
u32 usbpucr;
- usbpucr = at91_sys_read(AT91_MATRIX_USBPUCR);
+ usbpucr = at91_matrix_read(AT91_MATRIX_USBPUCR);
usbpucr &= ~AT91_MATRIX_USBPUCR_PUON;
- at91_sys_write(AT91_MATRIX_USBPUCR, usbpucr);
+ at91_matrix_write(AT91_MATRIX_USBPUCR, usbpucr);
}
clk_off(udc);
}
diff --git a/drivers/usb/gadget/atmel_usba_udc.c b/drivers/usb/gadget/atmel_usba_udc.c
index 5e10f651ad63..9f98508966d1 100644
--- a/drivers/usb/gadget/atmel_usba_udc.c
+++ b/drivers/usb/gadget/atmel_usba_udc.c
@@ -332,12 +332,12 @@ static int vbus_is_present(struct usba_udc *udc)
static void toggle_bias(int is_on)
{
- unsigned int uckr = at91_sys_read(AT91_CKGR_UCKR);
+ unsigned int uckr = at91_pmc_read(AT91_CKGR_UCKR);
if (is_on)
- at91_sys_write(AT91_CKGR_UCKR, uckr | AT91_PMC_BIASEN);
+ at91_pmc_write(AT91_CKGR_UCKR, uckr | AT91_PMC_BIASEN);
else
- at91_sys_write(AT91_CKGR_UCKR, uckr & ~(AT91_PMC_BIASEN));
+ at91_pmc_write(AT91_CKGR_UCKR, uckr & ~(AT91_PMC_BIASEN));
}
#else
diff --git a/drivers/usb/host/ohci-at91.c b/drivers/usb/host/ohci-at91.c
index 77afabc77f9b..8e855eb0bf89 100644
--- a/drivers/usb/host/ohci-at91.c
+++ b/drivers/usb/host/ohci-at91.c
@@ -448,10 +448,11 @@ static irqreturn_t ohci_hcd_at91_overcurrent_irq(int irq, void *data)
/* From the GPIO notifying the over-current situation, find
* out the corresponding port */
- gpio = irq_to_gpio(irq);
for (port = 0; port < ARRAY_SIZE(pdata->overcurrent_pin); port++) {
- if (pdata->overcurrent_pin[port] == gpio)
+ if (gpio_to_irq(pdata->overcurrent_pin[port]) == irq) {
+ gpio = pdata->overcurrent_pin[port];
break;
+ }
}
if (port == ARRAY_SIZE(pdata->overcurrent_pin)) {
diff --git a/drivers/watchdog/at91rm9200_wdt.c b/drivers/watchdog/at91rm9200_wdt.c
index b3046dc4b56c..7ceefd29ae14 100644
--- a/drivers/watchdog/at91rm9200_wdt.c
+++ b/drivers/watchdog/at91rm9200_wdt.c
@@ -51,7 +51,7 @@ static unsigned long at91wdt_busy;
*/
static inline void at91_wdt_stop(void)
{
- at91_sys_write(AT91_ST_WDMR, AT91_ST_EXTEN);
+ at91_st_write(AT91_ST_WDMR, AT91_ST_EXTEN);
}
/*
@@ -59,9 +59,9 @@ static inline void at91_wdt_stop(void)
*/
static inline void at91_wdt_start(void)
{
- at91_sys_write(AT91_ST_WDMR, AT91_ST_EXTEN | AT91_ST_RSTEN |
+ at91_st_write(AT91_ST_WDMR, AT91_ST_EXTEN | AT91_ST_RSTEN |
(((65536 * wdt_time) >> 8) & AT91_ST_WDV));
- at91_sys_write(AT91_ST_CR, AT91_ST_WDRST);
+ at91_st_write(AT91_ST_CR, AT91_ST_WDRST);
}
/*
@@ -69,7 +69,7 @@ static inline void at91_wdt_start(void)
*/
static inline void at91_wdt_reload(void)
{
- at91_sys_write(AT91_ST_CR, AT91_ST_WDRST);
+ at91_st_write(AT91_ST_CR, AT91_ST_WDRST);
}
/* ......................................................................... */