| Age | Commit message (Collapse) | Author |
|---|
|
When struct cfq_data allocation fails, cic_index need to be freed.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
The 'group_changed' variable is initialized to 0 and never changed, so
checking the variable is meaningless.
It is a leftover from 0bbfeb832042 ("cfq-iosched: Always provide group
iosolation."). Let's get rid of it.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Justin TerAvest <teravest@google.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Reduce the number of bit operations in cfq_choose_req() on average
(and worst) cases.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Simplify the calculation in cfq_prio_to_maxrq(), plus replace CFQ_PRIO_LISTS to
IOPRIO_BE_NR since they are the same and IOPRIO_BE_NR looks more reasonable in
this context IMHO.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
If we don't explicitly initialize it to zero, CFQ might think that
cgroup of ioc has changed and it generates lots of unnecessary calls
to call_for_each_cic(changed_cgroup). Fix it.
cfq_get_io_context()
cfq_ioc_set_cgroup()
call_for_each_cic(ioc, changed_cgroup)
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
02e352287a4 (block: rescan partitions on invalidated devices on
-ENOMEDIA too) relocated partition rescan above explicit bd_set_size()
to simplify condition check. As rescan_partitions() does its own bdev
size setting, this doesn't break anything; however,
rescan_partitions() prints out the following messages when adjusting
bdev size, which can be confusing.
sda: detected capacity change from 0 to 146815737856
sdb: detected capacity change from 0 to 146815737856
This patch restores the original order and remove the warning
messages.
stable: Please apply together with 02e352287a4 (block: rescan
partitions on invalidated devices on -ENOMEDIA too).
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Tony Luck <tony.luck@gmail.com>
Tested-by: Tony Luck <tony.luck@gmail.com>
Cc: stable@kernel.org
Stable note: 2.6.39 only.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Commit 73c101011926 ("block: initial patch for on-stack per-task plugging")
removed calls to elv_bio_merged() when @bio merged with @req. Re-add them.
This in turn will update merged stats in associated group. That
should be safe as long as request has got reference to the blkio_group.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Divyesh Shah <dpshah@google.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Make BLKIO_STAT_MERGED per cpu hence gettring rid of need of taking
blkg->stats_lock.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
We allocated per cpu stats struct for root group but did not free it.
Fix it.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
We don't need them anymore, so kill:
- REQ_ON_PLUG checks in various places
- !rq_mergeable() check in plug merging
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
This patch merges in a fix that missed 2.6.39 final.
Conflicts:
block/blk.h
|
|
Currently we take a queue lock on each bio to check if there are any
throttling rules associated with the group and also update the stats.
Now access the group under rcu and update the stats without taking
the queue lock. Queue lock is taken only if there are throttling rules
associated with the group.
So the common case of root group when there are no rules, save
unnecessary pounding of request queue lock.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Now dispatch stats update is lock free. But reset of these stats still
takes blkg->stats_lock and is dependent on that. As stats are per cpu,
we should be able to just reset the stats on each cpu without any locks.
(Atleast for 64bit arch).
On 32bit arch there is a small race where 64bit updates are not atomic.
The result of this race can be that in the presence of other writers,
one might not get 0 value after reset of a stat and might see something
intermediate
One can write more complicated code to cover this race like sending IPI
to other cpus to reset stats and for offline cpus, reset these directly.
Right not I am not taking that path because reset_update is more of a
debug feature and it can happen only on 32bit arch and possibility of
it happening is small. Will fix it if it becomes a real problem. For
the time being going for code simplicity.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Some of the stats are 64bit and updation will be non atomic on 32bit
architecture. Use sequence counters on 32bit arch to make reading
of stats safe.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Currently we take blkg_stat lock for even updating the stats. So even if
a group has no throttling rules (common case for root group), we end
up taking blkg_lock, for updating the stats.
Make dispatch stats per cpu so that these can be updated without taking
blkg lock.
If cpu goes offline, these stats simply disappear. No protection has
been provided for that yet. Do we really need anything for that?
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Soon we will allow accessing a throtl_grp under rcu_read_lock(). Hence
start freeing up throtl_grp after one rcu grace period.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Use same helper function for root group as we use with dynamically
allocated groups to add it to various lists.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
A helper function for the code which is used at 2-3 places. Makes reading
code little easier.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Currently, we allocate root throtl_grp statically. But as we will be
introducing per cpu stat pointers and that will be allocated
dynamically even for root group, we might as well make whole root
throtl_grp allocation dynamic and treat it in same manner as other
groups.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Currently, all the cfq_group or throtl_group allocations happen while
we are holding ->queue_lock and sleeping is not allowed.
Soon, we will move to per cpu stats and also need to allocate the
per group stats. As one can not call alloc_percpu() from atomic
context as it can sleep, we need to drop ->queue_lock, allocate the
group, retake the lock and continue processing.
In throttling code, I check the queue DEAD flag again to make sure
that driver did not call blk_cleanup_queue() in the mean time.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
blkg->key = cfqd is an rcu protected pointer and hence we used to do
call_rcu(cfqd->rcu_head) to free up cfqd after one rcu grace period.
The problem here is that even though cfqd is around, there are no
gurantees that associated request queue (td->queue) or q->queue_lock
is still around. A driver might have called blk_cleanup_queue() and
release the lock.
It might happen that after freeing up the lock we call
blkg->key->queue->queue_ock and crash. This is possible in following
path.
blkiocg_destroy()
blkio_unlink_group_fn()
cfq_unlink_blkio_group()
Hence, wait for an rcu peirod if there are groups which have not
been unlinked from blkcg->blkg_list. That way, if there are any groups
which are taking cfq_unlink_blkio_group() path, can safely take queue
lock.
This is how we have taken care of race in throttling logic also.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Nobody seems to be using cfq_find_alloc_cfqg() function parameter "create".
Get rid of that.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
cgroup unaccounted_time file is created only if CONFIG_DEBUG_BLK_CGROUP=y.
there are some fields which are out side this config option. Fix that.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Group initialization code seems to be at two places. root group
initialization in blk_throtl_init() and dynamically allocated group
in throtl_find_alloc_tg(). Create a common function and use at both
the places.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Since for-2.6.40/core was forked off the 2.6.39 devel tree, we've
had churn in the core area that makes it difficult to handle
patches for eg cfq or blk-throttle. Instead of requiring that they
be based in older versions with bugs that have been fixed later
in the rc cycle, merge in 2.6.39 final.
Also fixes up conflicts in the below files.
Conflicts:
drivers/block/paride/pcd.c
drivers/cdrom/viocd.c
drivers/ide/ide-cd.c
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
configfs: Fix race between configfs_readdir() and configfs_d_iput()
configfs: Don't try to d_delete() negative dentries.
ocfs2/dlm: Target node death during resource migration leads to thread spin
ocfs2: Skip mount recovery for hard-ro mounts
ocfs2/cluster: Heartbeat mismatch message improved
ocfs2/cluster: Increase the live threshold for global heartbeat
ocfs2/dlm: Use negotiated o2dlm protocol version
ocfs2: skip existing hole when removing the last extent_rec in punching-hole codes.
ocfs2: Initialize data_ac (might be used uninitialized)
|
|
* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
drivercore: revert addition of of_match to struct device
of: fix race when matching drivers
|
|
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
MIPS: Kludge IP27 build for 2.6.39.
MIPS: AR7: Fix GPIO register size for Titan variant.
MIPS: Fix duplicate invocation of notify_die.
MIPS: RB532: Fix iomap resource size miscalculation.
|
|
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time. This was unsafe
because matching is not an atomic operation with probing a driver. If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.
This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
blk_cleanup_queue() calls elevator_exit() and after this, we can't
touch the elevator without oopsing. __elv_next_request() must check
for this state because in the refcounted queue model, we can still
call it after blk_cleanup_queue() has been called.
This was reported as causing an oops attributable to scsi.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
If two drivers are probing devices at the same time, both will write
their match table result to the dev->of_match cache at the same time.
Only write the result if the device matches.
In a thread titled "SBus devices sometimes detected, sometimes not",
Meelis reported his SBus hme was not detected about 50% of the time.
From the debug suggested by Grant it was obvious another driver matched
some devices between the call to match the hme and the hme discovery
failling.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Milton Miller <miltonm@bga.com>
[grant.likely: modified to only call of_match_device() once]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: don't delay blk_run_queue_async
scsi: remove performance regression due to async queue run
blk-throttle: Use task_subsys_state() to determine a task's blkio_cgroup
block: rescan partitions on invalidated devices on -ENOMEDIA too
cdrom: always check_disk_change() on open
block: unexport DISK_EVENT_MEDIA_CHANGE for legacy/fringe drivers
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The 'size' variable contains the correct register size for both AR7
and Titan, but we never used it to ioremap the correct register size.
This problem only shows up on Titan.
[ralf@linux-mips.org: Fixed the fix. The original patch as in patchwork
recognizes the problem correctly then fails to fix it ...]
Reported-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/2380/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Initial patch by Yury Polyanskiy <ypolyans@princeton.edu>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2373/
|
|
This is the MIPS portion of Joe Perches <joe@perches.com>'s
https://patchwork.linux-mips.org/patch/2172/ which seems to have been
lost in time and space.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
configfs_readdir() will use the existing inode numbers of inodes in the
dcache, but it makes them up for attribute files that aren't currently
instantiated. There is a race where a closing attribute file can be
tearing down at the same time as configfs_readdir() is trying to get its
inode number.
We want to get the inode number of open attribute files, because they
should match while instantiated. We can't lock down the transition
where dentry->d_inode is set to NULL, so we just check for NULL there.
We can, however, ensure that an inode we find isn't iput() in
configfs_d_iput() until after we've accessed it.
Signed-off-by: Joel Becker <jlbec@evilplan.org>
|
|
When configfs is faking mkdir() on its subsystem or default group
objects, it starts by adding a negative dentry. It then tries to
instantiate the group. If that should fail, it must clean up after
itself.
I was using d_delete() here, but configfs_attach_group() promises to
return an empty dentry on error. d_delete() explodes with the entry
dentry. Let's try d_drop() instead. The unhashing is what we want for
our dentry.
Signed-off-by: Joel Becker <jlbec@evilplan.org>
|
|
Let's check a scenario:
1. blk_delay_queue(q, SCSI_QUEUE_DELAY);
2. blk_run_queue_async();
the second one will became a noop, because q->delay_work already has
WORK_STRUCT_PENDING_BIT set, so the delayed work will still run after
SCSI_QUEUE_DELAY. But blk_run_queue_async actually hopes the delayed
work runs immediately.
Fix this by doing a cancel on potentially pending delayed work
before queuing an immediate run of the workqueue.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] V4L: soc-camera: regression fix: calculate .sizeimage in soc_camera.c
[media] v4l2-subdev: fix broken subdev control enumeration
[media] Fix cx88 remote control input
[media] v4l: Release module if subdev registration fails
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, AMD: Fix ARAT feature setting again
Revert "x86, AMD: Fix APIC timer erratum 400 affecting K8 Rev.A-E processors"
x86, apic: Fix spurious error interrupts triggering on all non-boot APs
x86, mce, AMD: Fix leaving freed data in a list
x86: Fix UV BAU for non-consecutive nasids
x86, UV: Fix NMI handler for UV platforms
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf evlist: Fix per thread mmap setup
perf tools: Honour the cpu list parameter when also monitoring a thread list
kprobes, x86: Disable irqs during optimized callback
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: fix cifsConvertToUCS() for the mapchars case
cifs: add fallback in is_path_accessible for old servers
|
|
Provide a stub for proc_mkdir_mode() when CONFIG_PROC_FS is not
enabled, just like the stub for proc_mkdir().
Fixes this linux-next build error:
drivers/net/wireless/airo.c:4504: error: implicit declaration of function 'proc_mkdir_mode'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
os_dump_core() uses abort() to terminate UML in case of an fatal error.
glibc's abort() calls raise(SIGABRT) which makes use of tgkill().
tgkill() has no effect within UML's kernel threads because they are not
pthreads. As fallback abort() executes an invalid instruction to
terminate the process. Therefore UML gets killed by SIGSEGV and leaves a
ugly log entry in the host's kernel ring buffer.
To get rid of this we use our own abort routine.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ZONE_CONGESTED should be a state of global memory reclaim. If not, a busy
memcg sets this and give unnecessary throttoling in wait_iff_congested()
against memory recalim in other contexts. This makes system performance
bad.
I'll think about "memcg is congested!" flag is required or not, later.
But this fix is required first.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Acked-by: Ying Han <yinghan@google.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Adding the necessary MODULE_DEVICE_TABLE() information allows the driver
to be automatically loaded by udev.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Shreshtha Kumar SAHU <shreshthakumar.sahu@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix switch initialization to ensure that all switches have default routing
disabled. This guarantees that no unexpected RapidIO packets arrive to
the default port set by reset and there is no default routing destination
until it is properly configured by software.
This update also unifies handling of unmapped destinations by tsi57x, IDT
Gen1 and IDT Gen2 switches.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: <stable@kernel.org> [2.6.37+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
