summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2010-09-03tulip: use integrated netdev statsEric Dumazet
struct tulip_private is a bit large (order-1 allocation even on 32bit arch), try to shrink it, remove its net_device_stats field. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-03ipv6: Update ip-sysctl.txt documentation for recent changes to accept_ra and ↵Thomas Graf
forwarding Documentation for recent changes to the tunables accept_ra and forwarding. Signed-off-by: Thomas Graf <tgraf@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-03ipv6: add special mode forwarding=2 to send RS while configured as routerThomas Graf
Similar to accepting router advertisement, the IPv6 stack does not send router solicitations if forwarding is enabled. This patch enables this behavior to be overruled by setting forwarding to the special value 2. Signed-off-by: Thomas Graf <tgraf@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-03ipv6: add special mode accept_ra=2 to accept RA while configured as routerThomas Graf
The current IPv6 behavior is to not accept router advertisements while forwarding, i.e. configured as router. This does make sense, a router is typically not supposed to be auto configured. However there are exceptions and we should allow the current behavior to be overwritten. Therefore this patch enables the user to overrule the "if forwarding enabled then don't listen to RAs" rule by setting accept_ra to the special value of 2. An alternative would be to ignore the forwarding switch alltogether and solely accept RAs based on the value of accept_ra. However, I found that if not intended, accepting RAs as a router can lead to strange unwanted behavior therefore we it seems wise to only do so if the user explicitely asks for this behavior. Signed-off-by: Thomas Graf <tgraf@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-02drivers/net: avoid some skb->ip_summed initializationsEric Dumazet
fresh skbs have ip_summed set to CHECKSUM_NONE (0) We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers. Introduce skb_checksum_none_assert() helper so that we keep this assertion documented in driver sources. Change most occurrences of : skb->ip_summed = CHECKSUM_NONE; by : skb_checksum_none_assert(skb); Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-02Merge branch 'for-davem' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
2010-09-02bna: fix stats handlingEric Dumazet
get_stats() method incorrectly clears a global array before folding various stats. This can break SNMP applications. Switch to 64 bit flavor to work on a user supplied buffer, and provide 64bit counters even on 32bit arches. Fix a bug in bnad_netdev_hwstats_fill(), for rx_fifo_errors, missing a folding (only the last counter was taken into account) Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Rasesh Mody <rmody@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-02Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
2010-09-02net: arp: code cleanupChangli Gao
Clean the code up according to Documentation/CodingStyle. Don't initialize the variable dont_send in arp_process(). Remove the temporary varialbe flags in arp_state_to_flags(). Signed-off-by: Changli Gao <xiaosuo@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-02net: dev_add_pack() & __dev_remove_pack() changesEric Dumazet
Add a small helper ptype_head() to get the head to manipulate dev_add_pack() & __dev_remove_pack() can use a spinlock without blocking BH, since softirq use RCU, and these functions are run from process context only. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-02net: Improve comments in include/linux/phy.hPeter Meerwald
Correct state range of PHY bus addresses (i.e. 0-31) in comment, make spelling of PHY consistent in comments. Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-02ipvs: use pkts for SCTP tooJulian Anastasov
Use correctly the in_pkts packet counter also for SCTP Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-02net: another last_rx roundEric Dumazet
Kill last_rx use in l2tp and two net drivers Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01starfire: Temporary kludge to fix powerpc build.David S. Miller
Add a dma_addr_t 64-bit case for powerpc with 64-bit phys addresses. Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01tcp: update also tcp_output with regard to RFC 5681Gerrit Renker
Thanks to Ilpo Jarvinen, this updates also the initial window setting for tcp_output with regard to RFC 5681. Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01net: make rx_queue sysfs_ops conststephen hemminger
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01pxa168_eth: remove duplicated #includeHuang Weiyi
Remove duplicated #include('s) in drivers/net/pxa168_eth.c Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01mac80211: only cancel software-based scans on suspendJohn W. Linville
Otherwise the hardware scan handler could access an invalid scan request structure. The driver should cancel any pending hardware scans during the suspend process anyway, so also add a warning if the hardware scan is still pending when the device resumes. Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-09-01net: skbuff.c cleanupEric Dumazet
(skb->data - skb->head) can be changed by skb_headroom(skb) Remove some uses of NET_SKBUFF_DATA_USES_OFFSET, using (skb_end_pointer(skb) - skb->head) or (skb_tail_pointer(skb) - skb->head) : compiler does the right thing, and this is more readable for us ;) (struct skb_shared_info *) casts in pskb_expand_head() to help memcpy() to use aligned moves. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01skge: add GRO supportEric Dumazet
- napi_gro_flush() is exported from net/core/dev.c, to avoid an irq_save/irq_restore in the packet receive path. - use napi_gro_receive() instead of netif_receive_skb() - use napi_gro_flush() before calling __napi_complete() - turn on NETIF_F_GRO by default - Tested on a Marvell 88E8001 Gigabit NIC Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01drivers/net/can/mscan/mpc5xxx_can.c: Add of_node_put to avoid memory leakJulia Lawall
Add a call to of_node_put in the error handling code following a call to of_find_matching_node. This patch also moves the existing call to of_node_put after the call to iounmap in the error handling code, to make it possible to jump to of_node_put without doing iounmap. These appear to be disjoint operations, so the ordering doesn't matter. This patch furthermore changes the -ENODEV result in the error handling code for of_find_matching_node to a return of 0, as found in the error handling code for of_iomap, because the return type of the function is unsigned. The semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @r exists@ local idexpression x; expression E,E1,E2; statement S; @@ *x = (of_find_node_by_path |of_find_node_by_name |of_find_node_by_phandle |of_get_parent |of_get_next_parent |of_get_next_child |of_find_compatible_node |of_match_node |of_find_node_by_type |of_find_node_with_property |of_find_matching_node |of_parse_phandle )(...); ... if (x == NULL) S <... when != x = E *if (...) { ... when != of_node_put(x) when != if (...) { ... of_node_put(x); ... } ( return <+...x...+>; | * return ...; ) } ...> ( E2 = x; | of_node_put(x); ) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Reviewed-by: Wolfram Sang <w.sang@pengutronix.de> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01ns83820: Use helper to disable chip interruptsDenis Kirjanov
Use helper routine to disable chip interrupts. Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01net: tunnels should use rcu_dereferenceEric Dumazet
tunnel4_handlers, tunnel64_handlers, tunnel6_handlers and tunnel46_handlers are protected by RCU, but we dont use appropriate rcu primitives to scan them. rcu_lock() is already held by caller. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01bnx2x: Update version to 1.52.53-5Yaniv Rosner
Update version to 1.52.53-5 Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01bnx2x: Add BCM84823 to the supported PHYsYaniv Rosner
Add BCM84823 to the supported PHYs Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01bnx2x: Change BCM848xx LED configurationYaniv Rosner
Change 848xx LED configuration according to the new microcode (Boards were shipped with only with the new microcode) Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01bnx2x: Remove unneeded setting of XAUI low power to BCM8727Yaniv Rosner
Remove unneeded setting of XAUI low power to BCM8727. This was required only in older microcode which is not in the field. Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01bnx2x: Change BCM848xx configuration according to IEEEYaniv Rosner
Change BCM848xx behavior to fit IEEE such that setting 10Mb/100Mb will use force speed, and setting 1Gb/10Gb will use auto-negotiation with the specific speed advertised Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01bnx2x: Reset link before any new link settingsYaniv Rosner
Reset link before any new link settings to avoid potential link issue caused by previous link settings Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01bnx2x: Fix potential link issue In BCM8727 based boardsYaniv Rosner
In BCM8727 based boards, setting default 10G link speed after link was set to 1G may lead to link down issue. The problem was setting the right value, but to the wrong registers Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01bnx2x: Fix potential link issue of BCM8073/BCM8727Yaniv Rosner
Fix potential link issue caused by insufficient delay time during SPIROM load of BCM8073/BCM8727 Signed-off-by: Yaniv Rosner <yanivr@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01qlcnic: add cksum flagAmit Kumar Salecha
o New CKSUM flag added by fw to notify cksum is verified. o Update version to 5.0.9 Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01qlcnic: mac vlan learning supportAmit Kumar Salecha
Hypervisor allows, two VM's interfaces to have same mac address. These VM's interfaces get differentiate with Vlan tag. This patch add support to learn and configure mac+vlan filter on device. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01qlcnic: support mac learningAmit Kumar Salecha
Device eswitch need to configure with VM's mac address. Hypervisor doesn't provide any utility/callbacks to get VM's mac address. Unicast mac address filter improves performance and also provide packet loopback capability i.e communication between VM. Above features is by default off, can be turned on with module parameter 'mac_learn'. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01qlcnic: fix mac override capabilityRajesh Borundia
o Rename mac_learning to mac_override o Added check in set_mac to return error if mac override is disabled. o Disabling mac_override only supported for Non priviledged functions. Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01qlcnic: fix panic while using eth_hdrRajesh Borundia
o skb->mac_header is not set, so machine panics while using function eth_hdr. Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01qlcnic: fix mac anti spoof policyRajesh Borundia
o Allow enabling/disabling mac anti spoof policy only for Non privilege functions. Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01qlcnic: fix for setting default eswitch configRajesh Borundia
o Default eswitch config was set, even before eswitch capabilty get detected. As a result setting default config was getting fail. Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01qlcnic: fix mac addr readRajesh Borundia
o Mac addr was read from flash for every fw reset for Non-priviledge function.It should be read only once. o Remove unnecessary get_mac_addr callback Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01qlcnic: add api version in reg dumpRajesh Borundia
o ethtool reg version bumped to 2 Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-09-01qlcnic: backout firmware initialization updateSony Chacko
o Backing out "firmware initialization update" changes, commit-id "d4066833bb1b35fefb1dd45eb2b10659d46bf151". o fix heartbit spelling, it should be heartbeat Signed-off-by: Sony Chacko <sony.chacko@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-31stmmac: Fix another build warning.David S. Miller
drivers/net/stmmac/dwmac100_core.c: In function 'dwmac100_dump_mac_regs': drivers/net/stmmac/dwmac100_core.c:47: warning: cast from pointer to integer of different size Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-31gro: unexport tcp4_gro_receive and tcp4_gro_completeEric Dumazet
tcp4_gro_receive() and tcp4_gro_complete() dont need to be exported. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-31net: add a comment on netdev->last_rxEric Dumazet
As some driver authors seem to reintroduce dev->last_rx use, add a comment to strongly discourage this. Since commit 6cf3f41e6c0 (bonding, net: Move last_rx update into bonding recv logic), network drivers dont need to update last_rx themselves, unless they use this field to implement a timeout. Not updating last_rx helps not dirtying a cache line, improving performance in SMP. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-31pktgen: remove non used variableEric Dumazet
remove non used variable "queue" in pg_cleanup Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-31vlan: Use vlan_dev_real_dev in vlan_hwaccel_do_receiveJiri Pirko
[patch net-next-2.6] vlan: Use vlan_dev_real_dev in vlan_hwaccel_do_receive Use helper as in other places. Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-31Phonet: do not set POLLOUT in case of send buffer overflowRémi Denis-Courmont
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-31Phonet: correct sendmsg() error code from sock_alloc_send_skb()Rémi Denis-Courmont
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-31Phonet: restore flow control credits when sending failsRémi Denis-Courmont
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-31mac80211: cancel scan in ieee80211_restart_hw if software scan pendingJohn W. Linville
This function exists to clean-up after a hardware error or something similar. The restart is accomplished using the same infrastructure used to resume after a suspend. The suspend path cancels running scans, so it seems appropriate to do that here as well for software-based scans. If a hardware-based scan is pending, issue a warning message since this indicates that the drivers has failed to clean-up after itself. Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-10-04 16:32:33 +0000