summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-01-07[media] adv7842: mute audio before switching inputs to avoid noise/popsMats Randgaard
Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: Use defines to select EDID portMats Randgaard
Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: remove connector type. Never used for anything usefulMats Randgaard
May also be wrong if the receiver is connected to more than one connector. Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: increase wait timeMartin Bugge
Wait 5ms after main reset. The data-sheet doesn't specify the wait after i2c-controlled reset, so using same value as after pin-controlled reset. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: set default input in platform-dataMartin Bugge
Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: 625/525 line standard jitter fixMartin Bugge
Both the PAL and NTSC standards are interlaced where a frame consist of two fields. Total number of lines in a frame in both systems are an odd number so the two fields will have different length. In the 625 line standard ("PAL") the odd field of the frame is transmitted first, while in the 525 standard ("NTSC") the even field is transmitted first. This adds the possibility to change output config between the fields and standards. This setting will reduce the "format-jitter" on the signal sent by the pixelport moving the difference between the fields to vertical front/back-porch only. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: set defaults spa-locationMartin Bugge
For edid with no Source Physical Address (spa), set spa-location to default and use correct values from edid. Signed-off-by: Martin Bugge <marbugge@cisco.com> Cc: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: support YCrCb analog input, receive CEA formats as RGB on ↵Hans Verkuil
VGA input Added support for YCrCb analog input. If input is ADV7842_MODE_RGB and RGB quantization range is set to V4L2_DV_RGB_RANGE_AUTO, then video with CEA timings will be received as RGB. For ADV7842_MODE_COMP, automatic CSC mode will be selected. See table 48 on page 281 in "ADV7842 Hardware Manual, Rev. 0, January 2011" for details. Make sure that when switching inputs the RGB quantization range is updated as well. Also updated the platform_data in ezkit to ensure that what was the old default value is now explicitly specified, so the behavior for that board is unchanged. Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Cc: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: added DE vertical position in SDP-io-syncMartin Bugge
Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: save platform data in state structMartin Bugge
Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: properly enable/disable the irqsMartin Bugge
The method of disabling the irq-output pin caused many "empty" interrupts. Instead, actually disable/enable the interrupts by changing the interrupt masks. Also enable STORE_MASKED_IRQ in INT1 configuration, otherwise when HDMI events happen while the interrupt is masked those events will be ignored when the interrupt is unmasked. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: corrected setting of cp-register 0x91 and 0x8fMartin Bugge
Bit 6 of register 0x8f was cleared incorrectly (must be 1), and bit 4 of register 0x91 was set incorrectly (must be 0). These bits are undocumented, so we shouldn't modify them to values different from what the datasheet specifies. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7842: Re-worked query_dv_timings()Martin Bugge
This simplified the code quite a bit. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: initialize timings to CEA 640x480p59.94Hans Verkuil
This timing must be supported by all HDMI equipment, so that's a reasonable default. Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: sync polarities from platform dataMartin Bugge
Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: return immediately if the new timings are equal to what is ↵Mats Randgaard
configured Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: Enable HDMI_MODE interruptMats Randgaard
Some sources are initially detected as DVI, and change to HDMI later. This must be detected to set the right RGB quantization range. Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: adjust gain and offset for DVI-D signalsMats Randgaard
If the input signal is DVI-D and quantization range is RGB full range, gain and offset must be adjusted to get the right range on the output. Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: set restart_stdi_once flag when signal is lostMartin Bugge
If the restart_stdi_once trick fails to find a valid format the flag was never reset. Signed-off-by: Martin Bugge <marbugge@cisco.com> Cc: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: improve HDMI audio handlingMats Randgaard
- Mute audio before switching inputs to avoid noise/pops - Mute audio if audio FIFO over-/underflows (AD Recommended setting) - Reset FIFO if it over-/underflows (AD Recommended setting) Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: remove debouncing of ADV7604_FMT_CHANGE eventsMats Randgaard
ADV7604_FMT_CHANGE events was debounced in adv7604_isr() to avoid that a receiver with a unstable input signal would block the event handling for other inputs. This solution was prone to errors. A better protection agains interrupt blocking is to delay the call of the interrupt service routine in the adv7604 driver if too many interrupts are received within a given time. Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: return immediately if the new input is equal to what is ↵Mats Randgaard
configured Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: remove connector type. Never used for anything usefulMats Randgaard
May also be wrong if the receiver is connected to more than one connector. Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: improve EDID handlingMats Randgaard
- split edid_write_block() - do not use edid->edid before the validity check - Return -EINVAL if edid->pad is invalid - Save both registers for SPA port A - Set SPA location to default value if it is not found Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: set CEC address (SPA) in EDIDMats Randgaard
Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: select YPbPr if RGB_RANGE_FULL/LIMITED is set for VGA_COMP ↵Mats Randgaard
inputs Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: Receive CEA formats as RGB on VGA (RGB) inputMats Randgaard
If the input is ADV7604_INPUT_VGA_RGB and RGB quantization range is set to V4L2_DV_RGB_RANGE_AUTO, video with CEA timings will be received as RGB. For ADV7604_INPUT_VGA_COMP, automatic CSC mode will be selected. See table 44 on page 205 in "ADV7604 Hardware Manual, Rev. F, August 2010" for details. Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: adv7604_s_register clean upHans Verkuil
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: support 1366x768 DMT Reduced BlankingMartin Bugge
Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: add hdmi driver strength adjustmentMikhail Khelik
The driver strength is board dependent, so set it from the platform_data. Signed-off-by: Mikhail Khelik <mkhelik@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7604: add support for all the digital input portsMats Randgaard
The adv7604 supports four digital input ports. This patch adds support for all of them, instead of just port A. Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7511: verify EDID headerMartin Bugge
Ignore EDID's where the header is wrong. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7511: add VIC and audio CTS/N values to log_statusMartin Bugge
Improve status logging. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] adv7511: disable register reset by HPDMartin Bugge
Whenever the hotplug pin is pulled low the chip resets a whole bunch of registers. It turns out that this can be turned off on the adv7511. Do so, as this 'feature' introduces race conditions in setting up registers, particular when the hotplug pin bounces a lot. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] ad9389b: retry setup if the state is inconsistentMartin Bugge
Retry setup if the device is powered off when it should be powered on. This state can be caused by rapid hotplug toggles. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] ad9389b: remove rx-sense irq dependencyMartin Bugge
Removed dependency on rx-sense interrupt, it's a leftover from obsolete code. Removing this simplifies the code. Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] ad9389b: whitespace changes to improve readabilityMartin Bugge
Signed-off-by: Martin Bugge <marbugge@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] ad9389b: verify EDID headerMats Randgaard
Ignore EDIDs where the header is wrong. Signed-off-by: Mats Randgaard <matrandg@cisco.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] em28xx: only initialize extensions on the main interfaceMauro Carvalho Chehab
For devices with a separated audio-only interface (em2860), call em28xx_init_extension() only once. That fixes a bug with Kworld 305U (eb1a:e305): [ 658.730715] em2860 #0: V4L2 video device registered as video1 [ 658.730728] em2860 #0: V4L2 VBI device registered as vbi0 [ 658.736907] em2860 #0: Remote control support is not available for this card. [ 658.736965] em2860 #1: Remote control support is not available for this card. [ 658.737230] ------------[ cut here ]------------ [ 658.737246] WARNING: CPU: 2 PID: 60 at lib/list_debug.c:36 __list_add+0x8a/0xc0() [ 658.737256] list_add double add: new=ffff8800a9a40410, prev=ffff8800a9a40410, next=ffffffffa08720d0. [ 658.737266] Modules linked in: tuner_xc2028 netconsole rc_hauppauge em28xx_rc rc_core tuner_simple tuner_types tda9887 tda8290 tuner tvp5150 msp3400 em28xx_v4l em28xx tveeprom v4l2_common fuse ccm nf_conntrack_netbios_ns nf_conntrack_broadcast ipt_MASQUERADE ip6t_REJECT xt_conntrack ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6tabl e_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security bnep iptable_raw vfat fat arc4 iwldvm mac80211 x86_pkg_temp_thermal coretemp kvm_intel nfsd iwlwifi snd_hda_codec_hdmi kvm snd_hda _codec_realtek snd_hda_intel snd_hda_codec auth_rpcgss nfs_acl cfg80211 lockd snd_hwdep snd_seq btusb sunrpc crc32_pclmul bluetooth crc32c_intel snd_seq_device snd_pcm uvcvideo r8169 ghash_clmulni_intel videobuf2_vmalloc videobuf2_memops videobuf2_core snd_page_alloc snd_timer snd videodev mei_me iTCO_wdt mii shpchp joydev mei media iTCO_vendor_support lpc_ich m icrocode soundcore rfkill serio_raw i2c_i801 mfd_core nouveau i915 ttm i2c_algo_bit drm_kms_helper drm i2c_core mxm_wmi wmi video [ 658.738601] CPU: 2 PID: 60 Comm: kworker/2:1 Not tainted 3.13.0-rc1+ #18 [ 658.738611] Hardware name: SAMSUNG ELECTRONICS CO., LTD. 550P5C/550P7C/SAMSUNG_NP1234567890, BIOS P04ABI.013.130220.dg 02/20/2013 [ 658.738624] Workqueue: events request_module_async [em28xx] [ 658.738646] 0000000000000009 ffff8802209dfc68 ffffffff816a3c96 ffff8802209dfcb0 [ 658.738700] ffff8802209dfca0 ffffffff8106aaad ffff8800a9a40410 ffffffffa08720d0 [ 658.738754] ffff8800a9a40410 0000000000000000 0000000000000080 ffff8802209dfd00 [ 658.738814] Call Trace: [ 658.738836] [<ffffffff816a3c96>] dump_stack+0x45/0x56 [ 658.738851] [<ffffffff8106aaad>] warn_slowpath_common+0x7d/0xa0 [ 658.738864] [<ffffffff8106ab1c>] warn_slowpath_fmt+0x4c/0x50 [ 658.738880] [<ffffffffa0868a7d>] ? em28xx_init_extension+0x1d/0x80 [em28xx] [ 658.738898] [<ffffffff81343b8a>] __list_add+0x8a/0xc0 [ 658.738911] [<ffffffffa0868a98>] em28xx_init_extension+0x38/0x80 [em28xx] [ 658.738927] [<ffffffffa086a059>] request_module_async+0x19/0x110 [em28xx] [ 658.738942] [<ffffffff810873b5>] process_one_work+0x1f5/0x510 [ 658.738954] [<ffffffff81087353>] ? process_one_work+0x193/0x510 [ 658.738967] [<ffffffff810880bb>] worker_thread+0x11b/0x3a0 [ 658.738979] [<ffffffff81087fa0>] ? manage_workers.isra.24+0x2b0/0x2b0 [ 658.738992] [<ffffffff8108ea2f>] kthread+0xff/0x120 [ 658.739005] [<ffffffff8108e930>] ? kthread_create_on_node+0x250/0x250 [ 658.739017] [<ffffffff816b517c>] ret_from_fork+0x7c/0xb0 [ 658.739029] [<ffffffff8108e930>] ? kthread_create_on_node+0x250/0x250 [ 658.739040] ---[ end trace c1acd24b354108de ]--- [ 658.739051] em2860 #1: Remote control support is not available for this card. [ 658.742407] em28xx-audio.c: probing for em28xx Audio Vendor Class [ 658.742429] em28xx-audio.c: Copyright (C) 2006 Markus Rechberger [ 658.742440] em28xx-audio.c: Copyright (C) 2007-2011 Mauro Carvalho Chehab [ 658.744798] em28xx-audio.c: probing for em28xx Audio Vendor Class [ 658.744823] em28xx-audio.c: Copyright (C) 2006 Markus Rechberger [ 658.744836] em28xx-audio.c: Copyright (C) 2007-2011 Mauro Carvalho Chehab [ 658.746849] em28xx-audio.c: probing for em28xx Audio Vendor Class [ 658.746863] em28xx-audio.c: Copyright (C) 2006 Markus Rechberger [ 658.746874] em28xx-audio.c: Copyright (C) 2007-2011 Mauro Carvalho Chehab ... Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] em28xx: prevent registering wrong interfaces for audio-onlyMauro Carvalho Chehab
A few devices (em2860) use a separate interface for audio only Audio Vendor Class USB. That interface should not be used by Remote Controller, Analog TV or Digital TV. Prevents initializing all non-audio extensions for the audio only interface. Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] em28xx: unify module versionMauro Carvalho Chehab
Use the same module version on all em28xx sub-modules, and use the same naming convention to describe the driver. Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] em28xx: check if a device has audio earlierMauro Carvalho Chehab
Better to split chipset detection from the audio setup. So, move the detection code to em28xx_init_dev(). Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] em28xx: improve extension information messagesMauro Carvalho Chehab
Add a message with consistent prints before and after each extension initialization, and provide a better text for module load. While here, add a missing sanity check for extension finish code at em28xx-v4l extension. Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] em28xx: make em28xx-video to be a separate moduleMauro Carvalho Chehab
Now that all analog-specific code are at em28xx-video, convert it into an em28xx extension and load it as a separate module. Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com> Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] em28xx: unregister i2c bus 0 if bus 1 fails to registerMauro Carvalho Chehab
Fix the error handling logic, making it to unregister i2c bus 0, in case of a failure to register the second bus. Reported-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-07[media] em28xx: move analog-specific init to em28xx-videoMauro Carvalho Chehab
There are several init code inside em28xx-cards that are actually part of analog initialization. Move the code to em28x-video, in order to remove part of the mess. In thesis, no functional changes so far. Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-05[media] em28xx: Fix em28xx deplockMauro Carvalho Chehab
When em28xx extensions are loaded/removed, there are two locks: a single static em28xx_devlist_mutex that registers each extension and the struct em28xx dev->lock. When extensions are registered, em28xx_devlist_mutex is taken first, and then dev->lock. Be sure that, when extensions are being removed, the same order will be used. Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-05[media] em28xx: some cosmetic changesMauro Carvalho Chehab
In order to make easier for the next patches, do some cosmetic changes. No functional changes. Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-05[media] em28xx: move some video-specific functions to em28xx-videoMauro Carvalho Chehab
Now that we want to split the video handling to a separate module, move all video-specific functions to em28xx-video. No functional changes. Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
2014-01-05[media] tuner-xc2028: remove unused codeMauro Carvalho Chehab
This macro is not used. remove it. Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-08 01:34:40 +0000