Age | Commit message (Collapse) | Author |
|
commit e4457d9798adb96272468e93da663de9bd0a4198 upstream.
Use a dedicated buffer for the DMA transfer and make sure to detect
short transfers to avoid parsing a corrupt descriptor.
Fixes: 6e8cf7751f9f ("USB: add EPIC support to the io_edgeport driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1eac5c244f705182d1552a53e2f74e2775ed95d6 upstream.
Make sure to detect short control-message transfers rather than continue
with zero-initialised data when retrieving modem status and during
device initialisation.
Fixes: 52af95459939 ("USB: add USB serial ssu100 driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1b0aed2b1600f6e5c7b9acfbd610a4e351ef5232 upstream.
Make sure the received data has the required headers before parsing it.
Also drop the redundant urb-status check, which has already been handled
by the caller.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c528fcb116e61afc379a2e0a0f70906b937f1e2c upstream.
Make sure to check for short transfers before parsing the receive buffer
to avoid acting on stale data.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a89b94b53371bbfa582787c2fa3378000ea4263d upstream.
We're currently emulating the vbus and id interrupts in the OTGSC
read API, but we also need to make sure that if we're handling
the events with extcon that we don't enable the interrupts for
those events in the hardware. Therefore, properly emulate this
register if we're using extcon, but don't enable the interrupts.
This allows me to get my cable connect/disconnect working
properly without getting spurious interrupts on my device that
uses an extcon for these two events.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Fixes: 3ecb3e09b042 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f60f8ccd54e03c1afafb2b20ceb029a0eaf7a134 upstream.
With the id and vbus detection done via extcon we need to make
sure we poll the status of OTGSC properly by considering what the
extcon is saying, and not just what the register is saying. Let's
move this hw_wait_reg() function to the only place it's used and
simplify it for polling the OTGSC register. Then we can make
certain we only use the hw_read_otgsc() API to read OTGSC, which
will make sure we properly handle extcon events.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Fixes: 3ecb3e09b042 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
paths
commit 68bd6fc3cfa98ef253e17307ccafd8ef907b5556 upstream.
Returning from for_each_available_child_of_node() loop requires cleaning
up node refcount. Error paths lacked it so for example in case of
deferred probe, the refcount of phy node was left increased.
Fixes: 6d40500ac9b6 ("usb: ehci/ohci-exynos: Fix of_node_put() for child when getting PHYs")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
paths
commit 3f6026b1dcb3c8ee71198c485a72ac674c6890dd upstream.
Returning from for_each_available_child_of_node() loop requires cleaning
up node refcount. Error paths lacked it so for example in case of
deferred probe, the refcount of phy node was left increased.
Fixes: 6d40500ac9b6 ("usb: ehci/ohci-exynos: Fix of_node_put() for child when getting PHYs")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ab007cc94ff9d82f5a8db8363b3becbd946e58cf upstream.
The PML feature is not exposed to guests so we should not be forwarding
the vmexit either.
This commit fixes BSOD 0x20001 (HYPERVISOR_ERROR) when running Hyper-V
enabled Windows Server 2016 in L1 on hardware that supports PML.
Fixes: 843e4330573c ("KVM: VMX: Add PML support in VMX")
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1fb883bb827ee8efc1cc9ea0154f953f8a219d38 upstream.
L2 was running with uninitialized PML fields which led to incomplete
dirty bitmap logging. This manifested as all kinds of subtle erratic
behavior of the nested guest.
Fixes: 843e4330573c ("KVM: VMX: Add PML support in VMX")
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0b4c208d443ba2af82b4c70f99ca8df31e9a0020 upstream.
This reverts commit bc6134942dbbf31c25e9bd7c876be5da81c9e1ce.
A CPUID instruction executed in VMX non-root mode always causes a
VM-exit, regardless of the leaf being queried.
Fixes: bc6134942dbb ("KVM: nested VMX: disable perf cpuid reporting")
Signed-off-by: Jim Mattson <jmattson@google.com>
[The issue solved by bc6134942dbb has been resolved with ff651cb613b4
("KVM: nVMX: Add nested msr load/restore algorithm").]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 80354c29025833acd72ddac1ffa21c6cb50128cd upstream.
The interrupt line used for the watchdog is 12, according to the official
Intel Edison BSP code.
And indeed after fixing it we start getting an interrupt and thus the
watchdog starts working again:
[ 191.699951] Kernel panic - not syncing: Kernel Watchdog
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 78a3bb9e408b ("x86: intel-mid: add watchdog platform code for Merrifield")
Link: http://lkml.kernel.org/r/20170312150744.45493-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
probed
commit 75013fb16f8484898eaa8d0b08fed942d790f029 upstream.
Fix to the exception table entry check by using probed address
instead of the address of copied instruction.
This bug may cause unexpected kernel panic if user probe an address
where an exception can happen which should be fixup by __ex_table
(e.g. copy_from_user.)
Unless user puts a kprobe on such address, this doesn't
cause any problem.
This bug has been introduced years ago, by commit:
464846888d9a ("x86/kprobes: Fix a bug which can modify kernel code permanently").
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 464846888d9a ("x86/kprobes: Fix a bug which can modify kernel code permanently")
Link: http://lkml.kernel.org/r/148829899399.28855.12581062400757221722.stgit@devbox
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f35b6542c3ac3f28056d298348a81f7d56d3a041 upstream.
Fix Makefile for x86 support, dependency on CONFIG_COMMON_CLK
was not explicit
Fixes: 701190fd7419 ('clk: x86: add support for Lynxpoint LPSS clocks')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 68dee8e2f2cacc54d038394e70d22411dee89da2 upstream.
commit 8fd524b355da ("x86: Kill bad_dma_address variable") has killed
bad_dma_address variable and used instead of macro DMA_ERROR_CODE
which is always zero. Since dma_addr is unsigned, the statement
dma_addr >= DMA_ERROR_CODE
is always true, and not needed.
arch/x86/kernel/pci-calgary_64.c: In function ‘iommu_free’:
arch/x86/kernel/pci-calgary_64.c:299:2: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
if (unlikely((dma_addr >= DMA_ERROR_CODE) && (dma_addr < badend))) {
Fixes: 8fd524b355da ("x86: Kill bad_dma_address variable")
Signed-off-by: Nikola Pajkovsky <npajkovsky@suse.cz>
Cc: iommu@lists.linux-foundation.org
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Muli Ben-Yehuda <mulix@mulix.org>
Link: http://lkml.kernel.org/r/7612c0f9dd7c1290407dbf8e809def922006920b.1479161177.git.npajkovsky@suse.cz
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a9b4f08770b415f30f2fb0f8329a370c8f554aa3 upstream.
commit d32932d02e18 removed the irq_retrigger callback from the IO-APIC
chip and did not add it to the new IO-APIC-IR irq chip.
There is no harm because the interrupts are resent in software when the
retrigger callback is NULL, but it's less efficient. So restore them.
[ tglx: Massaged changelog ]
Fixes: d32932d02e18 ("x86/irq: Convert IOAPIC to use hierarchical irqdomain interfaces")
Signed-off-by: Ruslan Ruslichenko <rruslich@cisco.com>
Cc: xe-linux-external@cisco.com
Link: http://lkml.kernel.org/r/1484662432-13580-1-git-send-email-rruslich@cisco.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a5b60de6972decc6b50a39abb376077c3c3621c8 upstream.
This patch fixes the issue specific to AP. AP is started with WEP
security and external station is connected to it. Data path works
in this case. Now if AP is restarted with WPA/WPA2 security,
station is able to connect but ping fails.
Driver skips the deletion of WEP keys if interface type is AP.
Removing that redundant check resolves the issue.
Fixes: e57f1734d87a ("mwifiex: add key material v2 support")
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5f0a221f59ad6b72202ef9c6e232086de8c336f2 upstream.
We already ensure 64 bytes alignment and add padding if required
during skb_aggr allocation.
Alignment and padding in mwifiex_11n_form_amsdu_txpd() is redundant.
We may end up accessing more data than allocated size with this.
This patch fixes following issue by removing redundant padding.
[ 370.241338] skbuff: skb_over_panic: text:ffffffffc046946a len:3550
put:72 head:ffff880000110000 data:ffff8800001100e4 tail:0xec2 end:0xec0 dev:<NULL>
[ 370.241374] ------------[ cut here ]------------
[ 370.241382] kernel BUG at net/core/skbuff.c:104!
370.244032] Call Trace:
[ 370.244041] [<ffffffff8c3df5ec>] skb_put+0x44/0x45
[ 370.244055] [<ffffffffc046946a>]
mwifiex_11n_aggregate_pkt+0x1e9/0xa50 [mwifiex]
[ 370.244067] [<ffffffffc0467c16>] mwifiex_wmm_process_tx+0x44a/0x6b7
[mwifiex]
[ 370.244074] [<ffffffffc0411eb8>] ? 0xffffffffc0411eb8
[ 370.244084] [<ffffffffc046116b>] mwifiex_main_process+0x476/0x5a5
[mwifiex]
[ 370.244098] [<ffffffffc0461298>] mwifiex_main_process+0x5a3/0x5a5
[mwifiex]
[ 370.244113] [<ffffffff8be7e9ff>] process_one_work+0x1a4/0x309
[ 370.244123] [<ffffffff8be7f4ca>] worker_thread+0x20c/0x2ee
[ 370.244130] [<ffffffff8be7f2be>] ? rescuer_thread+0x383/0x383
[ 370.244136] [<ffffffff8be7f2be>] ? rescuer_thread+0x383/0x383
[ 370.244143] [<ffffffff8be83742>] kthread+0x11c/0x124
[ 370.244150] [<ffffffff8be83626>] ? kthread_parkme+0x24/0x24
[ 370.244157] [<ffffffff8c4da1ef>] ret_from_fork+0x3f/0x70
[ 370.244168] [<ffffffff8be83626>] ? kthread_parkme+0x24/0x24
Fixes: 84b313b35f8158d ("mwifiex: make tx packet 64 byte DMA aligned")
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6183468a23fc6b6903f8597982017ad2c7fdefcf upstream.
Similar to commit fcd2042e8d36 ("mwifiex: printk() overflow with 32-byte
SSIDs"), we failed to account for the existence of 32-char SSIDs in our
debugfs code. Unlike in that case though, we zeroed out the containing
struct first, and I'm pretty sure we're guaranteed to have some padding
after the 'ssid.ssid' and 'ssid.ssid_len' fields (the struct is 33 bytes
long).
So, this is the difference between:
# cat /sys/kernel/debug/mwifiex/mlan0/info
...
essid="0123456789abcdef0123456789abcdef "
...
and the correct output:
# cat /sys/kernel/debug/mwifiex/mlan0/info
...
essid="0123456789abcdef0123456789abcdef"
...
Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 448c077eeb02240c430db2a2c3bf5285a4c65d66 upstream.
'adr' yields a data-pointer, not a function-pointer.
Fixes: 999f934de195 ("ARM: omap5/dra7xx: Enable booting secondary
CPU in HYP mode")
Signed-off-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cbe99c538d1776009e8710755bb6e726f7fffa9b upstream.
gcc gets confused about the control flow in ktd2692_parse_dt(), causing
it to warn about what seems like a potential bug:
drivers/leds/leds-ktd2692.c: In function 'ktd2692_probe':
drivers/leds/leds-ktd2692.c:244:15: error: '*((void *)&led_cfg+8)' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/leds/leds-ktd2692.c:225:7: error: 'led_cfg.flash_max_microamp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/leds/leds-ktd2692.c:232:3: error: 'led_cfg.movie_max_microamp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The code is fine, and slightly reworking it in an equivalent way lets
gcc figure that out too, which gets rid of the warning.
Fixes: 77e7915b15bb ("leds: ktd2692: Add missing of_node_put")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ba52e75718784fda1b683ee0bfded72a0b83b047 upstream.
Reading both fault and status registers and logging any fault should
take priority over handling status register update.
Fix by moving the status handling to later in interrupt routine.
Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
irq_handle_thread()
commit 68abfb8015832ddf728b911769659468efaf8bd9 upstream.
Caching the fault register after a single I2C read may not keep an accurate
value.
Fix by doing two reads in irq_handle_thread() and using the cached value
elsewhere. If a safety timer fault later clears itself, we apparently don't get
an interrupt (INT), however other interrupts would refresh the register cache.
From the data sheet: "When a fault occurs, the charger device sends out INT
and keeps the fault state in REG09 until the host reads the fault register.
Before the host reads REG09 and all the faults are cleared, the charger
device would not send any INT upon new faults. In order to read the
current fault status, the host has to read REG09 two times consecutively.
The 1st reads fault register status from the last read [1] and the 2nd reads
the current fault register status."
[1] presumably a typo; should be "last fault"
Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
component
commit 2d9fee6a42ea170e4378b3363a7ad385d0e67281 upstream.
We wrongly get uevents for bq24190-charger and bq24190-battery on every
register change.
Fix by checking the association with charger and battery before
emitting uevent(s).
Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d62acc5ef0621463446091ebd7a345e06e9ab80c upstream.
The device specific data is not fully initialized on
request_threaded_irq(). This may cause a crash when the IRQ handler
tries to reference them.
Fix the issue by installing IRQ handler at the end of the probe.
Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e05ad7e0741ce0505e1df157c62b22b95172bb97 upstream.
pm_resume() does a register_reset() which clears charger host mode.
Fix by calling set_mode_host() after the reset.
Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 767eee362fd72bb2ca44cc80419ca4b38c6d8369 upstream.
The interrupt signal is TRIGGER_FALLING. This is is specified in the
data sheet PIN FUNCTIONS: "The INT pin sends active low, 256us
pulse to host to report charger device status and fault."
Also the direction can be seen in the data sheet Figure 37 "BQ24190
with D+/D- Detection and USB On-The-Go (OTG)" which shows a 10k
pull-up resistor installed for the sample configurations.
Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger")
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a7e0fb6c2029a780444d09560f739e020d54fe4d upstream.
Currently the opal_exit tracepoint usually shows the opcode as 0:
<idle>-0 [047] d.h. 635.654292: opal_entry: opcode=63
<idle>-0 [047] d.h. 635.654296: opal_exit: opcode=0 retval=0
kopald-1209 [019] d... 636.420943: opal_entry: opcode=10
kopald-1209 [019] d... 636.420959: opal_exit: opcode=0 retval=0
This is because we incorrectly load the opcode into r0 before calling
__trace_opal_exit(), whereas it expects the opcode in r3 (first function
parameter). In fact we are leaving the retval in r3, so opcode and
retval will always show the same value.
Instead load the opcode into r3, resulting in:
<idle>-0 [040] d.h. 636.618625: opal_entry: opcode=63
<idle>-0 [040] d.h. 636.618627: opal_exit: opcode=63 retval=0
Fixes: c49f63530bb6 ("powernv: Add OPAL tracepoints")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4cca0457686e4ee1677d69469e4ddfd94d389a80 upstream.
The switch that conditionally sets CPUPOWER_CAP_HAS_TURBO_RATIO and
CPUPOWER_CAP_IS_SNB flags is missing a break, so all cores get both
flags set and an assumed base clock of 100 MHz for turbo values.
Reported-by: GSR <gsr.bugs@infernal-iceberg.com>
Tested-by: GSR <gsr.bugs@infernal-iceberg.com>
References: https://bugs.debian.org/859978
Fixes: 8fb2e440b223 (cpupower: Show Intel turbo ratio support via ...)
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5008efc83bf85b647aa1cbc44718b1675bbb7444 upstream.
The PJ4 inline asm sequence to write to cp15 cannot be built in Thumb-2
mode, due to the way it performs arithmetic on the program counter, so it
is built in ARM mode instead. However, building C files in ARM mode under
CONFIG_THUMB2_KERNEL is problematic, since the instrumentation performed
by subsystems like ftrace does not expect having to deal with interworking
branches.
Since the sequence in question is simply a poor man's ISB instruction,
let's use a straight 'isb' instead when building in Thumb2 mode. Thumb2
implies V7, so 'isb' should always be supported in that case.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b5c66bab72a6a65edb15beb60b90d3cb84c5763b upstream.
posix_acl_update_mode() could possibly clear 'acl', if so we leak the
memory pointed by 'acl'. Save this pointer before calling
posix_acl_update_mode() and release the memory if 'acl' really gets
cleared.
Link: http://lkml.kernel.org/r/1486678332-2430-1-git-send-email-xiyou.wangcong@gmail.com
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reported-by: Mark Salyzyn <salyzyn@android.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Greg Kurz <groug@kaod.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
commit 4617f564c06117c7d1b611be49521a4430042287 upstream.
When calling a dm ioctl that doesn't process any data
(IOCTL_FLAGS_NO_PARAMS), the contents of the data field in struct
dm_ioctl are left initialized. Current code is incorrectly extending
the size of data copied back to user, causing the contents of kernel
stack to be leaked to user. Fix by only copying contents before data
and allow the functions processing the ioctl to override.
Signed-off-by: Adrian Salido <salidoa@google.com>
Reviewed-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 13bf9fbff0e5e099e2b6f003a0ab8ae145436309 upstream.
The NFSv2/v3 code does not systematically check whether we decode past
the end of the buffer. This generally appears to be harmless, but there
are a few places where we do arithmetic on the pointers involved and
don't account for the possibility that a length could be negative. Add
checks to catch these.
Reported-by: Tuomas Haanpää <thaan@synopsys.com>
Reported-by: Ari Kauppi <ari@synopsys.com>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit db44bac41bbfc0c0d9dd943092d8bded3c9db19b upstream.
Use a couple shortcuts that will simplify a following bugfix.
(Minor backporting required to account for a change from f34b95689d2c
"The NFSv2/NFSv3 server does not handle zero length WRITE requests
correctly".)
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 03a8bb0e53d9562276045bdfcf2b5de2e4cff5a1 upstream.
As Al pointed, d_revalidate should return RCU lookup before using d_inode.
This was originally introduced by:
commit 34286d666230 ("fs: rcu-walk aware d_revalidate method").
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3d43bcfef5f0548845a425365011c499875491b0 upstream.
This avoids potential problems caused by a race where the inode gets
renamed out from its parent directory and the parent directory is
deleted while ext4_d_revalidate() is running.
Fixes: 28b4c263961c
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 28b4c263961c47da84ed8b5be0b5116bad1133eb upstream.
Add a validation check for dentries for encrypted directory to make
sure we're not caching stale data after a key has been added or removed.
Also check to make sure that status of the encryption key is updated
when readdir(2) is executed.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9a200d075e5d05be1fcad4547a0f8aee4e2f9a04 upstream.
...otherwise an user can enable encryption for certain files even
when the filesystem is unable to support it.
Such a case would be a filesystem created by mkfs.ext4's default
settings, 1KiB block size. Ext4 supports encyption only when block size
is equal to PAGE_SIZE.
But this constraint is only checked when the encryption feature flag
is set.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver causes two warnings about possibly uninitialized variables:
drivers/infiniband/hw/ehca/ehca_mrmw.c: In function 'ehca_set_pagebuf':
drivers/infiniband/hw/ehca/ehca_mrmw.c:1908:4: warning: 'prev_pgaddr' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/infiniband/hw/ehca/ehca_mrmw.c:1924:14: note: 'prev_pgaddr' was declared here
drivers/infiniband/hw/ehca/ehca_mrmw.c: In function 'ehca_reg_mr':
drivers/infiniband/hw/ehca/ehca_mrmw.c:2430:5: warning: 'hret' may be used uninitialized in this function [-Wmaybe-uninitialized]
The first one is definitely a false positive, the second one may or may not
be one. In both cases, adding an intialization is the safe and easy
workaround.
The driver was removed in mainline in commit e581d111dad3
("staging/rdma: remove deprecated ehca driver"), in linux-4.6.
In 4.4, the file is located in drivers/staging/rdma/ehca/ehca_mrmw.c,
and the fix still applies.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We get this build warning on arm64
drivers/infiniband/hw/qib/qib_qp.c:44:0: error: "BITS_PER_PAGE" redefined [-Werror]
#define BITS_PER_PAGE (PAGE_SIZE*BITS_PER_BYTE)
This is fixed upstream in commit 898fa52b4ac3 ("IB/qib: Remove qpn, qp tables and
related variables from qib"), which does a lot of other things as well.
Instead, I just backport the rename of the local BITS_PER_PAGE definition to
RVT_BITS_PER_PAGE.
The driver first showed up in linux-2.6.35, and the fixup should still apply
to that. The upstream fix went into v4.6, so we could apply this workaround
to both 3.18 and 4.4.
Fixes: f931551bafe1 ("IB/qib: Add new qib driver for QLogic PCIe InfiniBand adapters")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The backport of d35c99ff77ec ("netlink: do not enter direct reclaim from
netlink_dump()") to the 4.4 branch (first in 4.4.32) mistakenly removed
direct claim from the initial large allocation _and_ the fallback
allocation which means that allocations can spuriously fail.
Fix the issue by adding back the direct reclaim flag to the fallback
allocation.
Fixes: 6d123f1d396b ("netlink: do not enter direct reclaim from netlink_dump()")
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c130b666a9a711f985a0a44b58699ebe14bb7245 upstream.
Commit f209fa03fc9d ("serial: 8250_pci: Detach low-level driver during
PCI error recovery") introduces a potential use-after-free in case the
pciserial_init_ports call in serial8250_io_resume fails, which may
happen if a memory allocation fails or if the .init quirk failed for
whatever reason). If this happen, further pci_get_drvdata will return a
pointer to freed memory.
This patch reworks the PCI recovery resume hook to restore the old priv
structure in this case, which should be ok, since the ports were already
detached. Such error during recovery causes us to give up on the
recovery.
Fixes: f209fa03fc9d ("serial: 8250_pci: Detach low-level driver during PCI error recovery")
Reported-by: Michal Suchanek <msuchanek@suse.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 05dab43230fdc0d14ca885b473a2740fe017ecb1 upstream.
When an EEH occurs during device initialization, the port timeout logic
can cause excessive delays as MMIO reads will fail. Depending on where
they are experienced, these delays can lead to a prolonged reset,
causing an unnecessary triggering of other timeout logic in the SCSI
stack or user applications.
To expedite recovery, the port timeout logic is updated to decay the
timeout at a much faster rate when in the presence of a likely EEH
frozen event.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1d3324c382b1a617eb567e3650dcb51f22dfec9a upstream.
The EEH reset handler is ignorant to the current state of the driver
when processing a frozen event and initiating a device reset. This can
be an issue if an EEH event occurs while a user or stack initiated reset
is executing. More specifically, if an EEH occurs while the SCSI host
reset handler is active, the reset initiated by the EEH thread will
likely collide with the host reset thread. This can leave the device in
an inconsistent state, or worse, cause a system crash.
As a remedy, the EEH handler is updated to evaluate the device state and
take appropriate action (proceed, wait, or disconnect host). The host
reset handler is also updated to handle situations where an EEH occurred
during a host reset. In such situations, the host reset handler will
delay reporting back a success to give the EEH reset an opportunity to
complete.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bbbfae962b7c221237c0f92547ee0c83f7204747 upstream.
When a port link is established, the AFU sends a 'link up' interrupt.
After the link is up, corresponding initialization steps are performed
on the card. Following that, when the card is ready for I/O, the AFU
sends 'login succeeded' interrupt. Today, cxlflash invokes
scsi_scan_host() upon receipt of both interrupts.
SCSI commands sent to the port prior to the 'login succeeded' interrupt
will fail with 'port not available' error. This is not desirable.
Moreover, when async_scan is active for the host, subsequent scan calls
are terminated with error. Due to this, the scsi_scan_host() call
performed after 'login succeeded' interrupt could portentially return
error and the devices may not be scanned properly.
To avoid this problem, scsi_scan_host() should be called only after the
'login succeeded' interrupt.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e434e04110704eb91acfecbd0fb8ca8e2da9c29b upstream.
The tg3_set_eeprom() function correctly initializes the 'start' variable,
but gcc generates a false warning:
drivers/net/ethernet/broadcom/tg3.c: In function 'tg3_set_eeprom':
drivers/net/ethernet/broadcom/tg3.c:12057:4: warning: 'start' may be used uninitialized in this function [-Wmaybe-uninitialized]
I have not come up with a way to restructure the code in a way that
avoids the warning without making it less readable, so this adds an
initialization for the declaration to shut up that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fddcca5107051adf9e4481d2a79ae0616577fd2c upstream.
When map_word gets too large, we use a lot of kernel stack, and for
MTD_MAP_BANK_WIDTH_32, this means we use more than the recommended
1024 bytes in a number of functions:
drivers/mtd/chips/cfi_cmdset_0020.c: In function 'cfi_staa_write_buffers':
drivers/mtd/chips/cfi_cmdset_0020.c:651:1: warning: the frame size of 1336 bytes is larger than 1024 bytes [-Wframe-larger-than=]
drivers/mtd/chips/cfi_cmdset_0020.c: In function 'cfi_staa_erase_varsize':
drivers/mtd/chips/cfi_cmdset_0020.c:972:1: warning: the frame size of 1208 bytes is larger than 1024 bytes [-Wframe-larger-than=]
drivers/mtd/chips/cfi_cmdset_0001.c: In function 'do_write_buffer':
drivers/mtd/chips/cfi_cmdset_0001.c:1835:1: warning: the frame size of 1240 bytes is larger than 1024 bytes [-Wframe-larger-than=]
This can be avoided if all operations on the map word are done
indirectly and the stack gets reused between the calls. We can
mostly achieve this by selecting MTD_COMPLEX_MAPPINGS whenever
MTD_MAP_BANK_WIDTH_32 is set, but for the case that no other
bank width is enabled, we also need to use a non-constant
map_bankwidth() to convince the compiler to use less stack.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[Brian: this patch mostly achieves its goal by forcing
MTD_COMPLEX_MAPPINGS (and the accompanying indirection) for 256-bit
mappings; the rest of the change is mostly a wash, though it helps
reduce stack size slightly. If we really care about supporting
256-bit mappings though, we should consider rewriting some of this
code to avoid keeping and assigning so many 256-bit objects on the
stack.]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2630628b2dbc3fc320aafaf84836119e4e3d62f1 upstream.
Apparently we now implicitly get definitions for BITS_PER_PAGE and
BITS_PER_PAGE_MASK from the pid_namespace.h
Instead of renaming our defines, I chose to define only if not yet
defined, but to double check the value if already defined.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b268c34e5ee92a4cc3099b0caaf26e6bfbdf0f18 upstream.
The awacs sound driver produces a false-positive warning in ppc64_defconfig:
sound/ppc/awacs.c: In function 'snd_pmac_awacs_init':
include/sound/control.h:219:9: warning: 'master_vol' may be used uninitialized in this function [-Wmaybe-uninitialized]
I haven't come up with a good way to rewrite the code to avoid the
warning, so here is a bad one: I initialize the variable before
the conditionall initialization so gcc no longer has to worry about
it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|