| Age | Commit message (Collapse) | Author |
|---|
|
Dont assume that all OMAP4+ code will be able to use OMAP4 hotplug
logic. On OMAP5, DRA7, we do not need this in place yet, also,
currently the CPU startup pointer is located in omap4_cpu_pm_info
instead of cpu_pm_ops.
So, isolate the function to hotplug_restart pointer in cpu_pm_ops
where it should have belonged, initalize them as per valid startup
pointers for OMAP4430/60 as in current logic, however provide
dummy_cpu_resume to be the startup location as well.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[nm@ti.com: split this out of original code and isolate it]
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
|
|
Get rid of all assumptions about always having a sar base on *all*
OMAP4+ platforms. We dont need one on DRA7 and it is not necessary at
this point for OMAP5 either.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[nm@ti.com: Split and optimize]
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
|
|
In addition to the standard power-management technique, the OMAP5 / DRA7
MPU subsystem also employs an SR3-APG (mercury) power management
technology to reduce leakage.
It allows for full logic and memories retention on MPU_C0 and MPU_C1 and
is controlled by the PRCM_MPU. Only "Fast-mode" is supported on the
OMAP5 and DRA7 family of processors.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[nm@ti.com: minor consolidation]
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
|
|
Enables MPUSS ES2 power management mode using ES2_PM_MODE in
AMBA_IF_MODE register.
0x0: OMAP5 ES1 behavior, CPU cores would enter and exit OFF mode together.
Broken! Fortunately, we do not support this anymore.
0x1: OMAP5 ES2, DRA7 behavior, CPU cores are allowed to enter/exit OFF mode
independently.
This is one time settings thanks to always ON domain.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[nm@ti.com: minor conflict resolutions, consolidation for DRA7]
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
|
|
With EMIF clock-domain put under hardware supervised control, memory
corruption and untraceable crashes are observed on OMAP5. Further
investigation revealed that there is a weakness in the PRCM on this
specific dynamic depedency.
The recommendation is to set MPUSS static dependency towards EMIF
clock-domain to avoid issues. This recommendation holds good for DRA7
family of devices as well.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[rnayak@ti.com: DRA7]
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[nm@ti.com: conflict resolution, dra7]
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
|
|
On OMAP5, RM_CPUi_CPUi_CONTEXT offset has changed. Update the code
so that same code works for OMAP4+ devices. DRA7 and OMAP5 have the same
context offset as well.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[rnayak@ti.com: for DRA7]
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[nm@ti.com: rebase, split/merge etc..]
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
|
|
Provide pdata-quirks for Am437x processor family.
Signed-off-by: Keerthy <j-keerthy@ti.com>
|
|
Provide pdata-quirks for DRA7 processor family.
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Provide pdata-quirks for OMAP5 processor family.
Signed-off-by: Nishanth Menon <nm@ti.com>
|
|
Allow the PRM interrupt information to be picked up from device tree.
OMAP3 may use legacy boot and needs to be compatible with old dtbs
(without interrupt populated), for these, we use the value which is
pre-populated.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
OMAP5 and DRA7 can now use pinctrl based I/O daisychain wakeup
capability. So, enable the support.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
"wkup" event at bit offset 0 exists only on OMAP3.
OMAP4430/60 PRM_IRQSTATUS_A9, OMAP5/DRA7 PRM_IRQSTATUS_MPU
register bit 0 is DPLL_CORE_RECAL_ST not wakeup event like OMAP3.
The same applies to AM437x as well.
Remove the wrong definition.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
Allow the PRM interrupt information to be picked up from device tree.
the only exception is for OMAP4 which uses values pre-populated and allows
compatibility with older dtb.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
use the generic function to pick up the prm_instance for a generic logic
which can be reused from OMAP4+
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
PRM device instance can vary depending on SoC. We already handle the
same during reset of the device, However, this is also needed
for other logic instances. So, first abstract this out to a generic
function.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull idle update from Len Brown:
"Two Intel-platform-specific updates to intel_idle, and a cosmetic
tweak to the turbostat utility"
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: tweak whitespace in output format
intel_idle: Broadwell support
intel_idle: Disable Baytrail Core and Module C6 auto-demotion
|
|
Power efficiency improves on Baytrail (Intel Atom Processor E3000)
when Linux disables C6 auto-demotion.
Based on work by Srinidhi Kasagar <srinidhi.kasagar@intel.com>.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: x86@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
"Part two of the PCI changes for v3.17:
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
It's a mechanical change that removes uses of the
DEFINE_PCI_DEVICE_TABLE macro. I waited until later in the merge
window to reduce conflicts, but it's possible you'll still see a few"
* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
|
|
Pull Sparc fixes from David Miller:
"Hook up the memfd syscall, and properly claim all PCI resources
discovered when building the PCI device tree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: Hook up memfd_create system call.
sparc64: Properly claim resources as each PCI bus is probed.
sparc64: Skip bogus PCI bridge ranges.
sparc64: Expand PCI bridge probing debug logging.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild
Pull kbuild updates from Michal Marek:
- make clean also considers $(extra-m) and $(extra-) to be consistent
- cleanup and fixes in scripts/Makefile.host
- allow to override the name of the Python 2 executable with make
PYTHON=... (only needed for ia64 in practice)
- option to split debugingo into *.dwo files to save disk space if the
compiler supports it (CONFIG_DEBUG_INFO_SPLIT)
- option to use dwarf4 debuginfo if the compiler supports it
(CONFIG_DEBUG_INFO_DWARF4)
- fix for disabling certain warnings with clang
- fix for unneeded rebuild with dash when a command contains
backslashes
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Fix handling of backslashes in *.cmd files
kbuild, LLVMLinux: Supress warnings unless W=1-3
Kbuild: Add a option to enable dwarf4 v2
kbuild: Support split debug info v4
kbuild: allow to override Python command name
kbuild: clean-up and bug fix of scripts/Makefile.host
kbuild: clean up scripts/Makefile.host
kbuild: drop shared library support from Makefile.host
kbuild: fix a bug of C++ host program handling
kbuild: fix a typo in scripts/Makefile.host
scripts/Makefile.clean: clean also $(extra-m) and $(extra-)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull more powerpc updates from Ben Herrenschmidt:
"Here are some more powerpc bits for 3.17, essentially fixes.
The biggest series, also aimed at -stable, is from Aneesh and is the
result of weeks and weeks of debugging to find out why the heck or THP
implementation was occasionally triggering multi-hit errors in our
level 1 TLB. It ended up being a combination of issues including
subtleties as to how we should invalidate those special 'MPSS' pages
we use to allow the use of 16M pages inside 4K/64K "base page size"
segments (you really have to love our MMU !)
Another interesting one in the "OMG" category is the series from
Michael adding memory barriers to spin_is_locked(). That's also the
result of many days of debugging to figure out why the semaphore code
would occasionally crash in ways that made no sense. It ended up
being some creative lock stacking that was defeated by the fact that
our locks allow a load inside the locked section to be re-ordered with
the load of the lock value itself (I'm still of two mind about whether
to kill that once and for all by putting a heavier barrier back into
our lock implementation...). The fixes come with a long explanation
in the cset comments, feel free to read it if you feel like having a
headache today"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (25 commits)
powerpc/thp: Add tracepoints to track hugepage invalidate
powerpc/mm: Use read barrier when creating real_pte
powerpc/thp: Use ACCESS_ONCE when loading pmdp
powerpc/thp: Invalidate with vpn in loop
powerpc/thp: Handle combo pages in invalidate
powerpc/thp: Invalidate old 64K based hash page mapping before insert of 4k pte
powerpc/thp: Don't recompute vsid and ssize in loop on invalidate
powerpc/thp: Add write barrier after updating the valid bit
powerpc: reorder per-cpu NUMA information's initialization
powerpc/perf/hv-24x7: Use kmem_cache_free
powerpc/pseries/hvcserver: Fix endian issue in hvcs_get_partner_info
powerpc: Hard disable interrupts in xmon
powerpc: remove duplicate definition of TEXASR_FS
powerpc/pseries: Avoid deadlock on removing ddw
powerpc/pseries: Failure on removing device node
powerpc/boot: Use correct zlib types for comparison
powerpc/powernv: Interface to register/unregister opal dump region
printk: Add function to return log buffer address and size
powerpc: Add POWER8 features to CPU_FTRS_POSSIBLE/ALWAYS
powerpc/ppc476: Disable BTAC
...
|
|
Pull device tree updates from Grant Likely:
"The branch contains the following device tree changes the v3.17 merge
window:
Group changes to the device tree. In preparation for adding device
tree overlay support, OF_DYNAMIC is reworked so that a set of device
tree changes can be prepared and applied to the tree all at once.
OF_RECONFIG notifiers see the most significant change here so that
users always get a consistent view of the tree. Notifiers generation
is moved from before a change to after it, and notifiers for a group
of changes are emitted after the entire block of changes have been
applied
Automatic console selection from DT. Console drivers can now use
of_console_check() to see if the device node is specified as a console
device. If so then it gets added as a preferred console. UART
devices get this support automatically when uart_add_one_port() is
called.
DT unit tests no longer depend on pre-loaded data in the device tree.
Data is loaded dynamically at the start of unit tests, and then
unloaded again when the tests have completed.
Also contains a few bugfixes for reserved regions and early memory
setup"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux: (21 commits)
of: Fixing OF Selftest build error
drivers: of: add automated assignment of reserved regions to client devices
of: Use proper types for checking memory overflow
of: typo fix in __of_prop_dup()
Adding selftest testdata dynamically into live tree
of: Add todo tasklist for Devicetree
of: Transactional DT support.
of: Reorder device tree changes and notifiers
of: Move dynamic node fixups out of powerpc and into common code
of: Make sure attached nodes don't carry along extra children
of: Make devicetree sysfs update functions consistent.
of: Create unlocked versions of node and property add/remove functions
OF: Utility helper functions for dynamic nodes
of: Move CONFIG_OF_DYNAMIC code into a separate file
of: rename of_aliases_mutex to just of_mutex
of/platform: Fix of_platform_device_destroy iteration of devices
of: Migrate of_find_node_by_name() users to for_each_node_by_name()
tty: Update hypervisor tty drivers to use core stdout parsing code.
arm/versatile: Add the uart as the stdout device.
of: Enable console on serial ports specified by /chosen/stdout-path
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen bugfixes from David Vrabel:
- fix ARM build
- fix boot crash with PVH guests
- improve reliability of resume/migration
* tag 'stable/for-linus-3.17-b-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: use vmap() to map grant table pages in PVH guests
x86/xen: resume timer irqs early
arm/xen: remove duplicate arch_gnttab_init() function
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Perform a pci_claim_resource() on all valid resources discovered
during the OF device tree scan.
Based almost entirely upon the PCI OF bus probing code which does
the same thing there.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems that when a PCI Express bridge is not in use and has no devices
behind it, the ranges property is bogus. Specifically the size property
is of the form [0xffffffff:...], and if you add this size to the resource
start address the 64-bit calculation will overflow.
Just check specifically for this size value signature and skip them.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dump the various aspects of the PCI bridge probed at boot time, most
importantly the bridge number ranges, and the ranges property.
This helps diagnose PCI resource issues and other problems by giving
ofpci_debug=1 on the boot command line.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"Several networking final fixes and tidies for the merge window:
1) Changes during the merge window unintentionally took away the
ability to build bluetooth modular, fix from Geert Uytterhoeven.
2) Several phy_node reference count bug fixes from Uwe Kleine-König.
3) Fix ucc_geth build failures, also from Uwe Kleine-König.
4) Fix klog false positivies when netlink messages go to network
taps, by properly resetting the network header. Fix from Daniel
Borkmann.
5) Sizing estimate of VF netlink messages is too small, from Jiri
Benc.
6) New APM X-Gene SoC ethernet driver, from Iyappan Subramanian.
7) VLAN untagging is erroneously dependent upon whether the VLAN
module is loaded or not, but there are generic dependencies that
matter wrt what can be expected as the SKB enters the stack.
Make the basic untagging generic code, and do it unconditionally.
From Vlad Yasevich.
8) xen-netfront only has so many slots in it's transmit queue so
linearize packets that have too many frags. From Zoltan Kiss.
9) Fix suspend/resume PHY handling in bcmgenet driver, from Florian
Fainelli"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (55 commits)
net: bcmgenet: correctly resume adapter from Wake-on-LAN
net: bcmgenet: update UMAC_CMD only when link is detected
net: bcmgenet: correctly suspend and resume PHY device
net: bcmgenet: request and enable main clock earlier
net: ethernet: myricom: myri10ge: myri10ge.c: Cleaning up missing null-terminate after strncpy call
xen-netfront: Fix handling packets on compound pages with skb_linearize
net: fec: Support phys probed from devicetree and fixed-link
smsc: replace WARN_ON() with WARN_ON_SMP()
xen-netback: Don't deschedule NAPI when carrier off
net: ethernet: qlogic: qlcnic: Remove duplicate object file from Makefile
wan: wanxl: Remove typedefs from struct names
m68k/atari: EtherNEC - ethernet support (ne)
net: ethernet: ti: cpmac.c: Cleaning up missing null-terminate after strncpy call
hdlc: Remove typedefs from struct names
airo_cs: Remove typedef local_info_t
atmel: Remove typedef atmel_priv_ioctl
com20020_cs: Remove typedef com20020_dev_t
ethernet: amd: Remove typedef local_info_t
net: Always untag vlan-tagged traffic on input.
drivers: net: Add APM X-Gene SoC ethernet driver support.
...
|
|
Pull Sparc fixes from David Miller:
"Sparc bug fixes, one of which was preventing successful SMP boots with
mainline"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix pcr_ops initialization and usage bugs.
sparc64: Do not disable interrupts in nmi_cpu_busy()
sparc: Hook up seccomp and getrandom system calls.
sparc: fix decimal printf format specifiers prefixed with 0x
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/apic updates from Thomas Gleixner:
"This is a major overhaul to the x86 apic subsystem consisting of the
following parts:
- Remove obsolete APIC driver abstractions (David Rientjes)
- Use the irqdomain facilities to dynamically allocate IRQs for
IOAPICs. This is a prerequisite to enable IOAPIC hotplug support,
and it also frees up wasted vectors (Jiang Liu)
- Misc fixlets.
Despite the hickup in Ingos previous pull request - caused by the
missing fixup for the suspend/resume issue reported by Borislav - I
strongly recommend that this update finds its way into 3.17. Some
history for you:
This is preparatory work for physical IOAPIC hotplug. The first
attempt to support this was done by Yinghai and I shot it down because
it just added another layer of obscurity and complexity to the already
existing mess without tackling the underlying shortcomings of the
current implementation.
After quite some on- and offlist discussions, I requested that the
design of this functionality must use generic infrastructure, i.e.
irq domains, which provide all the mechanisms to dynamically map linux
interrupt numbers to physical interrupts.
Jiang picked up the idea and did a great job of consolidating the
existing interfaces to manage the x86 (IOAPIC) interrupt system by
utilizing irq domains.
The testing in tip, Linux-next and inside of Intel on various machines
did not unearth any oddities until Borislav exposed it to one of his
oddball machines. The issue was resolved quickly, but unfortunately
the fix fell through the cracks and did not hit the tip tree before
Ingo sent the pull request. Not entirely Ingos fault, I also assumed
that the fix was already merged when Ingo asked me whether he could
send it.
Nevertheless this work has a proper design, has undergone several
rounds of review and the final fallout after applying it to tip and
integrating it into Linux-next has been more than moderate. It's the
ground work not only for IOAPIC hotplug, it will also allow us to move
the lowlevel vector allocation into the irqdomain hierarchy, which
will benefit other architectures as well. Patches are posted already,
but they are on hold for two weeks, see below.
I really appreciate the competence and responsiveness Jiang has shown
in course of this endavour. So I'm sure that any fallout of this will
be addressed in a timely manner.
FYI, I'm vanishing for 2 weeks into my annual kids summer camp kitchen
duty^Wvacation, while you folks are drooling at KS/LinuxCon :) But HPA
will have a look at the hopefully zero fallout until I'm back"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (53 commits)
x86, irq, PCI: Keep IRQ assignment for PCI devices during suspend/hibernation
x86/apic/vsmp: Make is_vsmp_box() static
x86, apic: Remove enable_apic_mode callback
x86, apic: Remove setup_portio_remap callback
x86, apic: Remove multi_timer_check callback
x86, apic: Replace noop_check_apicid_used
x86, apic: Remove check_apicid_present callback
x86, apic: Remove mps_oem_check callback
x86, apic: Remove smp_callin_clear_local_apic callback
x86, apic: Replace trampoline physical addresses with defaults
x86, apic: Remove x86_32_numa_cpu_node callback
x86: intel-mid: Use the new io_apic interfaces
x86, vsmp: Remove is_vsmp_box() from apic_is_clustered_box()
x86, irq: Clean up irqdomain transition code
x86, irq, devicetree: Release IOAPIC pin when PCI device is disabled
x86, irq, SFI: Release IOAPIC pin when PCI device is disabled
x86, irq, mpparse: Release IOAPIC pin when PCI device is disabled
x86, irq, ACPI: Release IOAPIC pin when PCI device is disabled
x86, irq: Introduce helper functions to release IOAPIC pin
x86, irq: Simplify the way to handle ISA IRQ
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/efix fixes from Peter Anvin:
"Two EFI-related Kconfig changes, which happen to touch immediately
adjacent lines in Kconfig and thus collapse to a single patch"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Enforce CONFIG_RELOCATABLE for EFI boot stub
x86/efi: Fix 3DNow optimization build failure in EFI stub
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/xsave changes from Peter Anvin:
"This is a patchset to support the XSAVES instruction required to
support context switch of supervisor-only features in upcoming
silicon.
This patchset missed the 3.16 merge window, which is why it is based
on 3.15-rc7"
* 'x86-xsave-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, xsave: Add forgotten inline annotation
x86/xsaves: Clean up code in xstate offsets computation in xsave area
x86/xsave: Make it clear that the XSAVE macros use (%edi)/(%rdi)
Define kernel API to get address of each state in xsave area
x86/xsaves: Enable xsaves/xrstors
x86/xsaves: Call booting time xsaves and xrstors in setup_init_fpu_buf
x86/xsaves: Save xstate to task's xsave area in __save_fpu during booting time
x86/xsaves: Add xsaves and xrstors support for booting time
x86/xsaves: Clear reserved bits in xsave header
x86/xsaves: Use xsave/xrstor for saving and restoring user space context
x86/xsaves: Use xsaves/xrstors for context switch
x86/xsaves: Use xsaves/xrstors to save and restore xsave area
x86/xsaves: Define a macro for handling xsave/xrstor instruction fault
x86/xsaves: Define macros for xsave instructions
x86/xsaves: Change compacted format xsave area header
x86/alternative: Add alternative_input_2 to support alternative with two features and input
x86/xsaves: Add a kernel parameter noxsaves to disable xsaves/xrstors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull metag architecture updates from James Hogan:
"Just a couple of minor static analysis fixes, removal of a NULL check
that should never happen, and fix an error check where an unsigned
value was being checked to see if it was negative"
* tag 'metag-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: cachepart: Fix failure check
metag: hugetlbpage: Remove null pointer checks that could never happen
|
|
Add tracepoint to track hugepage invalidate. This help us
in debugging difficult to track bugs.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
On ppc64 we support 4K hash pte with 64K page size. That requires
us to track the hash pte slot information on a per 4k basis. We do that
by storing the slot details in the second half of pte page. The pte bit
_PAGE_COMBO is used to indicate whether the second half need to be
looked while building real_pte. We need to use read memory barrier while
doing that so that load of hidx is not reordered w.r.t _PAGE_COMBO
check. On the store side we already do a lwsync in __hash_page_4K
CC: <stable@vger.kernel.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We would get wrong results in compiler recomputed old_pmd. Avoid
that by using ACCESS_ONCE
CC: <stable@vger.kernel.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
As per ISA, for 4k base page size we compare 14..65 bits of VA specified
with the entry_VA in tlb. That implies we need to make sure we do a
tlbie with all the possible 4k va we used to access the 16MB hugepage.
With 64k base page size we compare 14..57 bits of VA. Hence we cannot
ignore the lower 24 bits of va while tlbie .We also cannot tlb
invalidate a 16MB entry with just one tlbie instruction because
we don't track which va was used to instantiate the tlb entry.
CC: <stable@vger.kernel.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
If we changed base page size of the segment, either via sub_page_protect
or via remap_4k_pfn, we do a demote_segment which doesn't flush the hash
table entries. We do a lazy hash page table flush for all mapped pages
in the demoted segment. This happens when we handle hash page fault for
these pages.
We use _PAGE_COMBO bit along with _PAGE_HASHPTE to indicate whether a
pte is backed by 4K hash pte. If we find _PAGE_COMBO not set on the pte,
that implies that we could possibly have older 64K hash pte entries in
the hash page table and we need to invalidate those entries.
Use _PAGE_COMBO to determine the page size with which we should
invalidate the hash table entries on unmap.
CC: <stable@vger.kernel.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
If we changed base page size of the segment, either via sub_page_protect
or via remap_4k_pfn, we do a demote_segment which doesn't flush the hash
table entries. We do a lazy hash page table flush for all mapped pages
in the demoted segment. This happens when we handle hash page fault
for these pages.
We use _PAGE_COMBO bit along with _PAGE_HASHPTE to indicate whether a
pte is backed by 4K hash pte. If we find _PAGE_COMBO not set on the pte,
that implies that we could possibly have older 64K hash pte entries in
the hash page table and we need to invalidate those entries.
Handle this correctly for 16M pages
CC: <stable@vger.kernel.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The segment identifier and segment size will remain the same in
the loop, So we can compute it outside. We also change the
hugepage_invalidate interface so that we can use it the later patch
CC: <stable@vger.kernel.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
With hugepages, we store the hpte valid information in the pte page
whose address is stored in the second half of the PMD. Use a
write barrier to make sure clearing pmd busy bit and updating
hpte valid info are ordered properly.
CC: <stable@vger.kernel.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
There is an issue currently where NUMA information is used on powerpc
(and possibly ia64) before it has been read from the device-tree, which
leads to large slab consumption with CONFIG_SLUB and memoryless nodes.
NUMA powerpc non-boot CPU's cpu_to_node/cpu_to_mem is only accurate
after start_secondary(), similar to ia64, which is invoked via
smp_init().
Commit 6ee0578b4daae ("workqueue: mark init_workqueues() as
early_initcall()") made init_workqueues() be invoked via
do_pre_smp_initcalls(), which is obviously before the secondary
processors are online.
Additionally, the following commits changed init_workqueues() to use
cpu_to_node to determine the node to use for kthread_create_on_node:
bce903809ab3f ("workqueue: add wq_numa_tbl_len and
wq_numa_possible_cpumask[]")
f3f90ad469342 ("workqueue: determine NUMA node of workers accourding to
the allowed cpumask")
Therefore, when init_workqueues() runs, it sees all CPUs as being on
Node 0. On LPARs or KVM guests where Node 0 is memoryless, this leads to
a high number of slab deactivations
(http://www.spinics.net/lists/linux-mm/msg67489.html).
Fix this by initializing the powerpc-specific CPU<->node/local memory
node mapping as early as possible, which on powerpc is
do_init_bootmem(). Currently that function initializes the mapping for
the boot CPU, but we extend it to setup the mapping for all possible
CPUs. Then, in smp_prepare_cpus(), we can correspondingly set the
per-cpu values for all possible CPUs. That ensures that before the
early_initcalls run (and really as early as possible), the per-cpu NUMA
mapping is accurate.
While testing memoryless nodes on PowerKVM guests with a fix to the
workqueue logic to use cpu_to_mem() instead of cpu_to_node(), with a
guest topology of:
available: 2 nodes (0-1)
node 0 cpus: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49
node 0 size: 0 MB
node 0 free: 0 MB
node 1 cpus: 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99
node 1 size: 16336 MB
node 1 free: 15329 MB
node distances:
node 0 1
0: 10 40
1: 40 10
the slab consumption decreases from
Slab: 932416 kB
SUnreclaim: 902336 kB
to
Slab: 395264 kB
SUnreclaim: 359424 kB
And we a corresponding increase in the slab efficiency from
slab mem objs slabs
used active active
------------------------------------------------------------
kmalloc-16384 337 MB 11.28% 100.00%
task_struct 288 MB 9.93% 100.00%
to
slab mem objs slabs
used active active
------------------------------------------------------------
kmalloc-16384 37 MB 100.00% 100.00%
task_struct 31 MB 100.00% 100.00%
Powerpc didn't support memoryless nodes until recently (64bb80d87f01
"powerpc/numa: Enable CONFIG_HAVE_MEMORYLESS_NODES" and 8c272261194d
"powerpc/numa: Enable USE_PERCPU_NUMA_NODE_ID"). Those commits also
helped improve memory consumption with these kind of environments.
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Free memory allocated using kmem_cache_zalloc using kmem_cache_free
rather than kfree.
The Coccinelle semantic patch that makes this change is as follows:
// <smpl>
@@
expression x,E,c;
@@
x = \(kmem_cache_alloc\|kmem_cache_zalloc\|kmem_cache_alloc_node\)(c,...)
... when != x = E
when != &x
?-kfree(x)
+kmem_cache_free(c,x)
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
A buffer returned by H_VTERM_PARTNER_INFO contains device information
in big endian format, causing problems for little endian architectures.
This patch ensures that they are in cpu endian.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
xmon only soft disables interrupts. This seems like a bad idea - we
certainly don't want decrementer and PMU exceptions going off when
we are debugging something inside xmon.
This issue was uncovered when the hard lockup detector went off
inside xmon. To ensure we wont get a spurious hard lockup warning,
I also call touch_nmi_watchdog() when exiting xmon.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
It appears that commits 7f06f21d40a6 ("powerpc/tm: Add checking to
treclaim/trechkpt") and e4e38121507a ("KVM: PPC: Book3S HV: Add
transactional memory support") both added definitions of TEXASR_FS.
Remove one of them. At the same time, fix the alignment of the remaining
definition (should be tab-separated like the rest of the #defines).
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Function remove_ddw() could be called in of_reconfig_notifier and
we potentially remove the dynamic DMA window property, which invokes
of_reconfig_notifier again. Eventually, it leads to the deadlock as
following backtrace shows.
The patch fixes the above issue by deferring releasing the dynamic
DMA window property while releasing the device node.
=============================================
[ INFO: possible recursive locking detected ]
3.16.0+ #428 Tainted: G W
---------------------------------------------
drmgr/2273 is trying to acquire lock:
((of_reconfig_chain).rwsem){.+.+..}, at: [<c000000000091890>] \
.__blocking_notifier_call_chain+0x40/0x78
but task is already holding lock:
((of_reconfig_chain).rwsem){.+.+..}, at: [<c000000000091890>] \
.__blocking_notifier_call_chain+0x40/0x78
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock((of_reconfig_chain).rwsem);
lock((of_reconfig_chain).rwsem);
*** DEADLOCK ***
May be due to missing lock nesting notation
2 locks held by drmgr/2273:
#0: (sb_writers#4){.+.+.+}, at: [<c0000000001cbe70>] \
.vfs_write+0xb0/0x1f8
#1: ((of_reconfig_chain).rwsem){.+.+..}, at: [<c000000000091890>] \
.__blocking_notifier_call_chain+0x40/0x78
stack backtrace:
CPU: 17 PID: 2273 Comm: drmgr Tainted: G W 3.16.0+ #428
Call Trace:
[c0000000137e7000] [c000000000013d9c] .show_stack+0x88/0x148 (unreliable)
[c0000000137e70b0] [c00000000083cd34] .dump_stack+0x7c/0x9c
[c0000000137e7130] [c0000000000b8afc] .__lock_acquire+0x128c/0x1c68
[c0000000137e7280] [c0000000000b9a4c] .lock_acquire+0xe8/0x104
[c0000000137e7350] [c00000000083588c] .down_read+0x4c/0x90
[c0000000137e73e0] [c000000000091890] .__blocking_notifier_call_chain+0x40/0x78
[c0000000137e7490] [c000000000091900] .blocking_notifier_call_chain+0x38/0x48
[c0000000137e7520] [c000000000682a28] .of_reconfig_notify+0x34/0x5c
[c0000000137e75b0] [c000000000682a9c] .of_property_notify+0x4c/0x54
[c0000000137e7650] [c000000000682bf0] .of_remove_property+0x30/0xd4
[c0000000137e76f0] [c000000000052a44] .remove_ddw+0x144/0x168
[c0000000137e7790] [c000000000053204] .iommu_reconfig_notifier+0x30/0xe0
[c0000000137e7820] [c00000000009137c] .notifier_call_chain+0x6c/0xb4
[c0000000137e78c0] [c0000000000918ac] .__blocking_notifier_call_chain+0x5c/0x78
[c0000000137e7970] [c000000000091900] .blocking_notifier_call_chain+0x38/0x48
[c0000000137e7a00] [c000000000682a28] .of_reconfig_notify+0x34/0x5c
[c0000000137e7a90] [c000000000682e14] .of_detach_node+0x44/0x1fc
[c0000000137e7b40] [c0000000000518e4] .ofdt_write+0x3ac/0x688
[c0000000137e7c20] [c000000000238430] .proc_reg_write+0xb8/0xd4
[c0000000137e7cd0] [c0000000001cbeac] .vfs_write+0xec/0x1f8
[c0000000137e7d70] [c0000000001cc3b0] .SyS_write+0x58/0xa0
[c0000000137e7e30] [c00000000000a064] syscall_exit+0x0/0x98
Cc: stable@vger.kernel.org
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
While running command "drmgr -c phb -r -s 'PHB 528'", following
backtrace jumped out because the target device node isn't marked
with OF_DETACHED by of_detach_node(), which caused by error
returned from memory hotplug related reconfig notifier when
disabling CONFIG_MEMORY_HOTREMOVE. The patch fixes it.
ERROR: Bad of_node_put() on /pci@800000020000210/ethernet@0
CPU: 14 PID: 2252 Comm: drmgr Tainted: G W 3.16.0+ #427
Call Trace:
[c000000012a776a0] [c000000000013d9c] .show_stack+0x88/0x148 (unreliable)
[c000000012a77750] [c00000000083cd34] .dump_stack+0x7c/0x9c
[c000000012a777d0] [c0000000006807c4] .of_node_release+0x58/0xe0
[c000000012a77860] [c00000000038a7d0] .kobject_release+0x174/0x1b8
[c000000012a77900] [c00000000038a884] .kobject_put+0x70/0x78
[c000000012a77980] [c000000000681680] .of_node_put+0x28/0x34
[c000000012a77a00] [c000000000681ea8] .__of_get_next_child+0x64/0x70
[c000000012a77a90] [c000000000682138] .of_find_node_by_path+0x1b8/0x20c
[c000000012a77b40] [c000000000051840] .ofdt_write+0x308/0x688
[c000000012a77c20] [c000000000238430] .proc_reg_write+0xb8/0xd4
[c000000012a77cd0] [c0000000001cbeac] .vfs_write+0xec/0x1f8
[c000000012a77d70] [c0000000001cc3b0] .SyS_write+0x58/0xa0
[c000000012a77e30] [c00000000000a064] syscall_exit+0x0/0x98
Cc: stable@vger.kernel.org
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Avoids this warning:
arch/powerpc/boot/gunzip_util.c:118:9: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
PowerNV platform is capable of capturing host memory region when system
crashes (because of host/firmware). We have new OPAL API to register/
unregister memory region to be captured when system crashes.
This patch adds support for new API. Also during boot time we register
kernel log buffer and unregister before doing kexec.
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
