summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2009-10-22e1000e: reset the PHY on 82577/82578 when going to SxBruce Allan
The PHY on 82577/82578 parts needs a soft reset when transitioning to Sx state in order for the PHY write which disables gigabit speed to take effect. Gigabit speed must be disabled in order for the PHY writes to registers on page 800 (the wakeup control registers) to work as expected otherwise the system might not wake via WoL. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-22netxen: avoid undue board config checkDhananjay Phadke
Old code assumed board config version in the flash to be 1. When this will get changed by tools, driver just refuses to attach. This is unnecessary since driver does not have to parse board config structure directly (maintained by firmware). Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-22netxen: fix tx timeout handling on firmware hangAmit Kumar Salecha
Clear NX_RESETING bit in netxen_tx_timeout_task() so that the firmware watchdog task can catch need_reset request from tx timeout. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-22netxen: fix i2c initDhananjay Phadke
Avoid resetting subsys ID in i2c block. Also remove duplicate check for address tranlsation error. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-21niu: VLAN_ETH_HLEN should be used to make sure that the whole MAC header was ↵Joyce Yu
copied to the head buffer in the Vlan packets case Signed-off-by: Joyce Yu <joyce.yu@sun.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-20KS8851: Fix ks8851_set_rx_mode() for IFF_MULTICASTBen Dooks
In ks8851_set_rx_mode() the case handling IFF_MULTICAST was also setting the RXCR1_AE bit by accident. This meant that all unicast frames where being accepted by the device. Remove RXCR1_AE from this case. Note, RXCR1_AE was also masking a problem with setting the MAC address properly, so needs to be applied after fixing the MAC write order. Fixes a bug reported by Doong, Ping of Micrel. This version of the patch avoids setting RXCR1_ME for all cases. Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-20KS8851: Fix MAC address write orderBen Dooks
The MAC address register was being written in the wrong order, so add a new address macro to convert mac-address byte to register address and a ks8851_wrreg8() function to write each byte without having to worry about any difficult byte swapping. Fixes a bug reported by Doong, Ping of Micrel. Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-20KS8851: Add soft reset at probe timeBen Dooks
Issue a full soft reset at probe time. This was reported by Doong Ping of Micrel, but no explanation of why this is necessary or what bug it is fixing. Add it as it does not seem to hurt the current driver and ensures that the device is in a known state when we start setting it up. Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-20net: fix section mismatch in fec.cSteven King
fec_enet_init is called by both fec_probe and fec_resume, so it shouldn't be marked as __init. Signed-off-by: Steven King <sfking@fdwdc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-18ethoc: clear only pending irqsThomas Chou
This patch fixed the problem of dropped packets due to lost of interrupt requests. We should only clear what was pending at the moment we read the irq source reg. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-18ethoc: inline regs accessThomas Chou
Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-16vmxnet3: use dev_dbg, fix build for CONFIG_BLOCK=nRandy Dunlap
vmxnet3 was using dprintk() for debugging output. This was defined in <linux/dst.h> and was the only thing that was used from that header file. This caused compile errors when CONFIG_BLOCK was not enabled due to bio* and BIO* uses in the header file, so change this driver to use dev_dbg() for debugging output. include/linux/dst.h:520: error: dereferencing pointer to incomplete type include/linux/dst.h:520: error: 'BIO_POOL_BITS' undeclared (first use in this function) include/linux/dst.h:521: error: dereferencing pointer to incomplete type include/linux/dst.h:522: error: dereferencing pointer to incomplete type include/linux/dst.h:525: error: dereferencing pointer to incomplete type make[4]: *** [drivers/net/vmxnet3/vmxnet3_drv.o] Error 1 Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Bhavesh Davda <bhavesh@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-14virtio_net: use dev_kfree_skb_any() in free_old_xmit_skbs()Eric Dumazet
Because netpoll can call netdevice start_xmit() method with irqs disabled, drivers should not call kfree_skb() from their start_xmit(), but use dev_kfree_skb_any() instead. Oct 8 11:16:52 172.30.1.31 [113074.791813] ------------[ cut here ]------------ Oct 8 11:16:52 172.30.1.31 [113074.791813] WARNING: at net/core/skbuff.c:398 \ skb_release_head_state+0x64/0xc8() Oct 8 11:16:52 172.30.1.31 [113074.791813] Hardware name: Oct 8 11:16:52 172.30.1.31 [113074.791813] Modules linked in: netconsole ocfs2 jbd2 quota_tree \ ocfs2_dlmfs ocfs2_stack_o2cb ocfs2_dlm ocfs2_nodemanager ocfs2_stackglue configfs crc32c drbd cn loop \ serio_raw psmouse snd_pcm snd_timer snd soundcore snd_page_alloc virtio_net pcspkr parport_pc parport \ i2c_piix4 i2c_core button processor evdev ext3 jbd mbcache dm_mirror dm_region_hash dm_log dm_snapshot \ dm_mod ide_cd_mod cdrom ata_generic ata_piix virtio_blk libata scsi_mod piix ide_pci_generic ide_core \ virtio_pci virtio_ring virtio floppy thermal fan thermal_sys [last unloaded: netconsole] Oct 8 11:16:52 172.30.1.31 [113074.791813] Pid: 11132, comm: php5-cgi Tainted: G W \ 2.6.31.2-vserver #1 Oct 8 11:16:52 172.30.1.31 [113074.791813] Call Trace: Oct 8 11:16:52 172.30.1.31 [113074.791813] <IRQ> [<ffffffff81253cd5>] ? \ skb_release_head_state+0x64/0xc8 Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81253cd5>] ? skb_release_head_state+0x64/0xc8 Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81049ae1>] ? warn_slowpath_common+0x77/0xa3 Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81253cd5>] ? skb_release_head_state+0x64/0xc8 Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81253a1a>] ? __kfree_skb+0x9/0x7d Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffffa01cb139>] ? free_old_xmit_skbs+0x51/0x6e \ [virtio_net] Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffffa01cbc85>] ? start_xmit+0x26/0xf2 [virtio_net] Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff8126934f>] ? netpoll_send_skb+0xd2/0x205 Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffffa0429216>] ? write_msg+0x90/0xeb [netconsole] Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81049f06>] ? __call_console_drivers+0x5e/0x6f Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff8102b49d>] ? kvm_clock_read+0x4d/0x52 Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff8104a082>] ? release_console_sem+0x115/0x1ba Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff8104a632>] ? vprintk+0x2f2/0x34b Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff8106b142>] ? vx_update_load+0x18/0x13e Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81308309>] ? printk+0x4e/0x5d Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff8102b49d>] ? kvm_clock_read+0x4d/0x52 Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81070b62>] ? getnstimeofday+0x55/0xaf Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81062683>] ? ktime_get_ts+0x21/0x49 Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff810626b7>] ? ktime_get+0xc/0x41 Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81062788>] ? hrtimer_interrupt+0x9c/0x146 Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81024a4b>] ? smp_apic_timer_interrupt+0x80/0x93 Oct 8 11:16:52 172.30.1.31 [113074.791813] [<ffffffff81011663>] ? apic_timer_interrupt+0x13/0x20 Oct 8 11:16:52 172.30.1.31 [113074.791813] <EOI> [<ffffffff8130a9eb>] ? _spin_unlock_irq+0xd/0x31 Reported-and-tested-by: Massimo Cetra <mcetra@navynet.it> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Bug-Entry: http://bugzilla.kernel.org/show_bug.cgi?id=14378 Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-14be2net: fix support for PCI hot plugSathya Perla
Before issuing any cmds to the FW, the driver must first wait till the fW becomes ready. This is needed for PCI hot plug when the driver can be probed while the card fw is being initialized. Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-14be2net: fix promiscuous and multicast promiscuous modes being enabled alwaysSathya Perla
Signed-off-by: Sathya Perla <sathyap@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-14vmxnet: fix 2 build problemsRandy Dunlap
vmxnet3 uses in_dev* interfaces so it should depend on INET. Also fix so that the driver builds when CONFIG_PCI_MSI is disabled. vmxnet3_drv.c:(.text+0x2a88cb): undefined reference to `in_dev_finish_destroy' drivers/net/vmxnet3/vmxnet3_drv.c:1335: error: 'struct vmxnet3_intr' has no member named 'msix_entries' drivers/net/vmxnet3/vmxnet3_drv.c:1384: error: 'struct vmxnet3_intr' has no member named 'msix_entries' drivers/net/vmxnet3/vmxnet3_drv.c:2137: error: 'struct vmxnet3_intr' has no member named 'msix_entries' drivers/net/vmxnet3/vmxnet3_drv.c:2138: error: 'struct vmxnet3_intr' has no member named 'msix_entries' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Bhavesh davda <bhavesh@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-14net: add support for STMicroelectronics Ethernet controllers.Giuseppe Cavallaro
This is the driver for the ST MAC 10/100/1000 on-chip Ethernet controllers (Synopsys IP blocks). Driver documentation: o http://stlinux.com/drupal/kernel/network/stmmac Revisions: o http://stlinux.com/drupal/kernel/network/stmmac-driver-revisions Performances: o http://stlinux.com/drupal/benchmarks/networking/stmmac Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-14net: ks8851_mll uses mii interfacesRandy Dunlap
From: Randy Dunlap <randy.dunlap@oracle.com> ks8851_mll uses mii interfaces so it needs to select MII. ks8851_mll.c:(.text+0xf95ac): undefined reference to `generic_mii_ioctl' ks8851_mll.c:(.text+0xf96a0): undefined reference to `mii_ethtool_gset' ks8851_mll.c:(.text+0xf96fa): undefined reference to `mii_ethtool_sset' ks8851_mll.c:(.text+0xf9754): undefined reference to `mii_link_ok' ks8851_mll.c:(.text+0xf97ae): undefined reference to `mii_nway_restart' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-14net/fec_mpc52xx: Fix kernel panic on FEC errorJohn Bonesio
The MDIO bus cannot be accessed at interrupt context, but on an FEC error, the fec_mpc52xx driver reset function also tries to reset the PHY. Since the error is detected at IRQ context, and the PHY functions try to sleep, the kernel ends up panicking. Resetting the PHY on an FEC error isn't even necessary. This patch solves the problem by removing the PHY reset entirely. Signed-off-by: John Bonesio <bones@secretlab.ca> Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-14net: Fix OF platform drivers coldplug/hotplug when compiled as modulesAnton Vorontsov
Some OF platform drivers are missing module device tables, so they won't load automatically on boot. This patch fixes the issue by adding proper MODULE_DEVICE_TABLE() macros to the drivers. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-13TI DaVinci EMAC: Clear statistics register properly.Sriram
The mechanism to clear the statistics register is dependent on the status of GMIIEN bit in MAC control register. If the GMIIEN bit is set, the stats registers are write to decrement. If the GMIIEN bit is cleared, the stats registers are plain read/write registers. The stats register clearing operation must take into account the current state of GMIIEN as it can be cleared when the interface is brought down. With existing implementation logic, querying for interface stats when the interface is down, can corrupt the statistics counters. This patch examines the GMIIEN bit status in MAC_CONTROL register before choosing an appropriate mask for clearing stats registers. Signed-off-by: Sriramakrishnan <srk@ti.com> Acked-by: Chaithrika U S <chaithrika@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-13r8169: partial support and phy init for the 8168dfrançois romieu
Extracted from Realtek's 8.012.00 r8168 driver. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Tested-by: Simon Farnsworth <simon.farnsworth@onelan.com> Cc: Edward Hsu <edward_hsu@realtek.com.tw> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-13Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2009-10-13irda/sa1100_ir: check return value of startup hookDmitry Artamonow
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-13WAN: fix Cisco HDLC handshaking.Krzysztof Halasa
Cisco HDLC uses keepalive packets and sequence numbers to determine link state. In rare cases both ends could transmit keepalive packets at the same time, causing the received sequence numbers to be treated as incorrect. Now we accept our current sequence number as well as the previous one. Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-133c574_cs: spin_lock the set_multicast_list functionKen Kawasaki
3c574_cs: spin_lock the set_multicast_list function. Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-13net: Teach pegasus driver to ignore bluetoother adapters with clashing ↵Chris Rankin
Vendor:Product IDs The Belkin F8T012xx1 bluetooth adaptor has the same vendor and product IDs as the Belkin F5D5050, so we need to teach the pegasus driver to ignore adaptors belonging to the "Wireless" class 0xE0. For this one case anyway, seeing as pegasus is a driver for "Wired" adaptors. Signed-off-by: Chris Rankin <rankincj@yahoo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-13netxen: fix pci bar mappingDhananjay Phadke
Use resource_size_t for PCI resource remapping instead of unsigned long. Physical addresses can exceed range of long data type (e.g with PAE). Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-13ethoc: fix warning from 32bit buildAlan Cox
drivers/net/ethoc.c: In function ‘ethoc_open’: drivers/net/ethoc.c:667: warning: comparison of distinct pointer types lacks a cast Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-13libertas: fix buildAlan Cox
drivers/net/wireless/libertas/cmdresp.c: In function ‘lbs_process_event’: drivers/net/wireless/libertas/cmdresp.c:519: error: ‘TASK_INTERRUPTIBLE’ undeclared (first use in this function) drivers/net/wireless/libertas/cmdresp.c:519: error: (Each undeclared identifier is reported only once drivers/net/wireless/libertas/cmdresp.c:519: error: for each function it appears in.) Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-13net: VMware virtual Ethernet NIC driver: vmxnet3Shreyas Bhatewara
Ethernet NIC driver for VMware's vmxnet3 From: Shreyas Bhatewara <sbhatewara@vmware.com> This patch adds driver support for VMware's virtual Ethernet NIC: vmxnet3 Guests running on VMware hypervisors supporting vmxnet3 device will thus have access to improved network functionalities and performance. Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com> Signed-off-by: Bhavesh Davda <bhavesh@vmware.com> Signed-off-by: Ronghua Zhang <ronghua@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-13net: Fix IXP 2000 network driver building.Vincent Sanders
The IXP 2000 network driver was failing to build as it has its own statistics gathering which was not compatible with the recent network device operations changes. This patch fixes the driver in the obvious way and has been compile tested. I have been unable to get the ixp2000 maintainer to comment or test this fix. Signed-off-by: Vincent Sanders <vince@simtec.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-12libertas: fix buildAlan Cox
drivers/net/wireless/libertas/cmdresp.c: In function ‘lbs_process_event’: drivers/net/wireless/libertas/cmdresp.c:519: error: ‘TASK_INTERRUPTIBLE’ undeclared (first use in this function) drivers/net/wireless/libertas/cmdresp.c:519: error: (Each undeclared identifier is reported only once drivers/net/wireless/libertas/cmdresp.c:519: error: for each function it appears in.) Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-12b43: fix ieee80211_rx() contextJohannes Berg
Due to the way it interacts with the networking stack and other parts of mac80211, ieee80211_rx() must be called with disabled softirqs. [1] http://thread.gmane.org/gmane.linux.kernel.wireless.general/39440/focus=40266 Reported-by: Dave Young <hidave.darkstar@gmail.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-12iwlwifi: change the order of freeing memoryWey-Yi Guy
Need to free the dynamic allocated memory before ieee80211_free_hw(); once call ieee80211_free_hw(), should not reference to "priv" data structure. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-12acenic: Pass up error code from ace_load_firmware()Ben Hutchings
If ace_load_firmware() fails, ace_init() cleans up but still returns 0, leading to an oops as seen in <http://bugs.debian.org/521383>. It should pass the error code up. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-09net: Link in PHY drivers before others.David S. Miller
We need PHY drivers to initialize in a static kernel before the MAC drivers that use them. So link them in first. Based upon a report by Felix Radensky. Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-08ibm_newemac: Added 16K Tx FIFO size support for EMAC4Dave Mitchell
Some of the EMAC V4 implementations support 16K Tx FIFOs. This patch adds support for this functionality and fixes typos in the Tx FIFO size error messages. Signed-off-by: Dave Mitchell <dmitchell@appliedmicro.com> Acked-by: Prodyut Hazarika <phazarika@appliedmicro.com> Acked-by: Victor Gallardo <vgallardo@appliedmicro.com> Acked-by: Loc Ho <lho@appliedmicro.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-08qlge: Add disable/enable firmare irqs to handler.Ron Mercer
This was accidentally omitted from one of the previous patches for firmware event handling. The handler needs to the enable firmware irq mask when it's done processing or it may not get any more events interrupts. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-08qlge: Restore rx mode after internal reset.Ron Mercer
Call set_multi API after reset recovery. This was exposed by tripping tx_timeout. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-08qlge: Fix chip reset process.Ron Mercer
Add wait for NIC fifo and MGMNT fifo to empty before applying reset. Otherwise broken frames can be processed by management processor and cause it to hang. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-08qlge: Fix RX multicast filter settings.Ron Mercer
The addresses were being added to the filter properly, but were not being enabled. This adds enable bit to filter write. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-08qlge: Fix frame routing for multicast frames.Ron Mercer
Broadcast/multicast should always be routed to the default (zeroeth) rx ring. Broadcast frames are already routed correctly. This fixes routing for multicast frames. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-08qlge: Fix frame routing issue related to bonding.Ron Mercer
Currently frames are routed based on their type and MAC address. This patch adds the port number on which the frame arrived to the routing. This prevents problems in the case where both interfaces have the same MAC address in a routing configuration. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-08qlge: Fix RSS hashing values.Ron Mercer
Fix RX queue table size and change from random to default hash values. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-08Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2009-10-07znet: Don't claim DMA lock around free_dma() calls.David S. Miller
It's not necessary and it's illegal too. Reported-by: Alexander Strakh <strakh@ispras.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-07b43: do not stack-allocate pio rx/tx header and tail buffersAlbert Herranz
The DMA-API debugging facility complains about b43 mapping memory from stack for SDIO-based cards. Indeed, b43 currently allocates the PIO RX/TX header and tail buffers from stack. The solution here is to use heap-allocated buffers instead. Signed-off-by: Albert Herranz <albert_herranz@yahoo.es> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-07b43: Fix PPC crash in rfkill polling on unloadLarry Finger
In Bugzilla No. 14181, a PowerMac G4 crashes on ifdown or module unload because the rfkill polling has not been stopped. For the x86 architectures, the attempt to reach a now unmapped register is not fatal as it is on PPC. (Includes "b43: Fix locking problem when stopping rfkill polling". -- JWL) Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-10-07mac80211: fix ADM8211_SYNCTL_RFtype defineRoel Kluin
A logical of shifts to the left doesn't make sense. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-10-30 23:35:00 +0000