| Age | Commit message (Collapse) | Author |
|---|
|
You can set this through sysfs, so don't mix the two.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
saa6588 always blocked while waiting for data, even if the filehandle
was in non-blocking mode.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
CMD_CLOSE sets data_available_for_read to 1, which is necessary to do the
wakeup call, but it is never reset to 0.
Because of this calling CMD_POLL afterwards will always return that data is
available, even if there isn't any.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
There are no controls for the radio node, so just drop support for this ioctl.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
This driver is independent from saa7134, so there is no reason why this
shouldn't be in media/i2c like all other i2c media drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The saa7134 driver is now converted to the control framework, so drop the
control compat code in saa6752hs.c.
Also add 'const' to several static arrays.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
NO_SYNC was meant for DVB and shouldn't be used anymore.
In this case NO_SIGNAL is a good alternative.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The empress video node can share resource management with the normal
video nodes, thus allowing for code sharing and making the empress node
non-exclusive.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Use the saa7134_fh struct for the empress video node as well, drop the dev
pointer from that struct since we can use drvdata for that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The video and empress nodes can share various ioctls.
Drop the input/std ioctls from the radio node (out of spec).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
These fields are global, not per-filehandle.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
videobuf2 file I/O emulation assumed that buffers dequeued from the
driver would return in the order they were enqueued in the driver.
Improve the file I/O emulator's book-keeping to remove this assumption.
Also set the buf->size properly if a write() dequeues a buffer and the
VB2_FILEIO_WRITE_IMMEDIATELY flag is set.
Based on an initial patch by Andy Walls.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
This works together with the retry_start_streaming mechanism to allow userspace
to start streaming even if not all required buffers have been queued.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Tomasz Stanislawski <t.stanislaws@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Two fixes:
- there is no need to set the index when calling dqbuf: dqbuf will
overwrite it.
- __vb2_init_fileio already starts streaming for write(), so there is
no need to do it again in __vb2_perform_fileio. It can never have
worked anyway: either __vb2_init_fileio succeeds in starting streaming
or it is never going to happen.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
If start_streaming returns -ENOBUFS, then it will be retried the next time
a buffer is queued. This means applications no longer need to know how many
buffers need to be queued before STREAMON can be called. This is particularly
useful for output stream I/O.
If a DMA engine needs at least X buffers before it can start streaming, then
for applications to get a buffer out as soon as possible they need to know
the minimum number of buffers to queue before STREAMON can be called. You can't
just try STREAMON after every buffer since on failure STREAMON will dequeue
all your buffers. (Is that a bug or a feature? Frankly, I'm not sure).
This patch simplifies applications substantially: they can just call STREAMON
at the beginning and then start queuing buffers and the DMA engine will
kick in automagically once enough buffers are available.
This also fixes using write() to stream video: the fileio implementation
calls streamon without having any queued buffers, which will fail today for
any driver that requires a minimum number of buffers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The read/write implementation in vb2 reuses existing vb2 functions, but
it sets q->fileio to NULL before calling them in order to skip the
'q->fileio != NULL' check.
This works today due to the synchronous nature of read/write, but it
1) is ugly, and 2) will fail in an asynchronous use-case such as a
thread queuing and dequeuing buffers. This last example will be necessary
in order to implement vb2 DVB support.
This patch removes the hack by splitting up the dqbuf/qbuf/streamon/streamoff
functions into an external and an internal version. The external version
checks q->fileio and then calls the internal version. The read/write
implementation now just uses the internal version, removing the need to
set q->fileio to NULL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
When preparing a buffer the queue lock is released for a short while
if the memory mode is USERPTR (see __buf_prepare for the details), which
would allow a race with a REQBUFS which can free the buffers. Removing the
buffers from underneath __buf_prepare is obviously a bad idea, so we
check if any of the buffers is in the state PREPARING, and if so we
just return -EAGAIN.
If this happens, then the application does something really strange. The
REQBUFS call can be retried safely, since this situation is transient.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The callback used to merge the common code of the qbuf/prepare_buf
code can be removed now that the mmap_sem handling is pushed down to
__buf_prepare(). This makes the code more readable.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Changeset b18a8ff29d80 added a comment violating the 80cols max size,
with no good reason.
Fix it.
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Rather than taking the mmap semaphore at a relatively high-level function,
push it down to the place where it is really needed.
It was placed in vb2_queue_or_prepare_buf() to prevent racing with other
vb2 calls. The only way I can see that a race can happen is when two
threads queue the same buffer. The solution for that it to introduce
a PREPARING state.
Moving it down offers opportunities to simplify the code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The struct vpdma_data_format holds the color format depth and the data_type
value needed to be programmed in the data descriptors. However, it doesn't
tell what type of color format is it, i.e, whether it is RGB, YUV or Misc.
This information is needed when by vpdma library when forming descriptors. We
modify the depth parameter for the chroma portion of the NV12 format. For this,
we check if the data_type value is C420. This isn't sufficient as there are
many YUV and RGB vpdma formats which have the same data_type value. Hence, we
need to hold the type of the color format for the above case, and possibly more
cases in the future.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Use the csc library functions to configure the CSC block in VPE.
Some changes are required in try_fmt to handle the pix->colorspace parameter
more correctly. Previously, we copied the source queue colorspace to the
destination queue colorspace as we didn't support RGB formats. Now, we configure
pix->colorspace based on the color format set(and the height of the image if
it's a YUV format).
Add basic RGB color formats to the list of supported vpe formats.
If the destination format is RGB colorspace, we also need to use the RGB output
port instead of the Luma and Chroma output ports. This requires configuring the
output data descriptors differently.
Also, make the default colorspace V4L2_COLORSPACE_SMPTE170M as that resembles
the Standard Definition colorspace more closely.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The CSC block can be used for color space conversion between YUV and RGB
formats.
It is configurable via a programmable set of coefficients. Add functionality to
choose the appropriate CSC coefficients and program them in the CSC registers.
We take the source and destination colorspace formats as the arguments, and
choose the coefficient table accordingly.
YUV to RGB coefficients are provided for standard and high definition
colorspaces. The coefficients can also be limited or full range. For now, only
full range coefficients are chosen. We would need some sort of control ioctl for
the user to specify the range needed. Not sure if there is a generic control
ioctl for this already?
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
VPE and VIP IPs in DAR7x contain a color space converter(CSC) sub block. Create
a library which will perform CSC related configurations and hold CSC register
definitions. The functions provided by this library will be called by the vpe
and vip drivers using a csc_data handle.
The vpe_dev holds the csc_data handle. The handle represents an instance of the
CSC hardware, and the vpe driver uses it to access the CSC register offsets or
helper functions to configure these registers.
The CSC register offsets are now relative to the CSC block itself, so we need
to use the macro GET_OFFSET_TOP to get the CSC register offset relative to the
VPE IP in the vpe driver.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Add the required SC register configurations which lets us perform linear scaling
for the supported range of horizontal and vertical scaling ratios.
The horizontal scaler performs polyphase scaling using it's 8 tap 32 phase
filter, decimation is performed when downscaling passes beyond 2x or 4x.
The vertical scaler performs polyphase scaling using it's 5 tap 32 phase filter,
it switches to a simpler form of scaling using the running average filter when
the downscale ratio is more than 4x.
Many of the SC features like peaking, trimming and non-linear scaling aren't
implemented for now. Only the minimal register fields required for basic scaling
operation are configured.
The function to configure SC registers takes the sc_data handle, the source and
destination widths and heights, and the scaler address data block offsets for
the current context so that they can be configured.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Make the driver allocate dma buffers to store horizontal and scaler coeffs.
Use the scaler library api to choose and copy scaler coefficients to a
the above buffers based on the scaling ratio. Since the SC block comes after
the de-interlacer, make sure that the source height is doubled if de-interlacer
was used.
These buffers now need to be used by VPDMA to load the coefficients into the
SRAM within SC.
In device_run, add configuration descriptors which have payloads pointing to
the scaler coefficients in memory. Use the members in sc_data handle to prevent
addition of these descriptors if there isn't a need to re-load coefficients into
SC. This comes helps unnecessary re-loading of the coefficients when we switch
back and forth between vpe contexts.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The SC block in VPE/VIP contains a SRAM within it. This internal memory
requires to be loaded with appropriate scaler coefficients from a contiguous
block of memory through VPDMA.
The horizontal and vertical scaler each require 2 sets of scaler coefficients
for luma and chroma scaling. The horizontal polyphase scaler requires
coefficients for a 32 phase and 8 tap filter. Similarly, the vertical scaler
requires coefficients for a 5 tap filter.
The choice of the scaler coefficients depends on the scaling ratio. Add
coefficient tables for different scaling ratios in sc_coeffs.h. In the case of
horizontal downscaling, we need to consider the change in ratio caused by
decimation performed by the horizontal scaler.
In order to load the scaler coefficients via VPDMA, a configuration descriptor
is used in block mode. The payload for the descriptor is the scaler coefficients
copied to memory. Coefficients for each phase have to be placed in memory in a
particular order understood by the scaler hardware.
The choice of the scaler coefficients, and the loading of the coefficients from
our tables to a contiguous buffer is managed by the functions
sc_set_hs_coefficients and sc_set_vs_coefficients.
The sc_data handle is now added with some parameters to describe the state of
the coefficients loaded in the SC block. 'loaded_coeff_h' and 'loaded_coeff_v'
hold the address of the last dma buffer which was used by VPDMA to copy
coefficients. This information can be used by a vpe mem-to-mem context to decide
whether it should load coefficients or not. 'hs_index' and 'vs_index' provide
some optimization by preventing loading of coefficients if the scaling ratio
didn't change between 2 contexts. 'load_coeff_h' and 'load_coeff_v' tell the
vpe/vip driver whether we need to load the coefficients through VPDMA or not.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
VPE and VIP IPs in DAR7x contain a scaler(SC) sub block. Create a library which
will perform scaler block related configurations and hold SC register
definitions. The functions provided by this library will be called by the vpe
and vip drivers using a sc_data handle.
The vpe_dev holds the sc_data handle. The handle represents an instance of the
SC hardware, and the vpe driver uses it to access the scaler register offsets
or helper functions to configure these registers.
We move the SC register definitions to sc.h so that they aren't specific to
VPE anymore. The register offsets are now relative to the sub-block, and not the
VPE IP as a whole. In order for VPDMA to configure registers, it requires it's
offset from the top level VPE module. A macro called GET_OFFSET_TOP is added to
return the offset of the register relative to the VPE IP.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The (d)qbuf ioctls were traced in the low-level v4l2 ioctl function. The
trace was outside the serialization lock, so that can affect the usefulness
of the timing. In addition, the __user pointer was expected instead of a
proper kernel pointer.
By moving the tracepoints to video_usercopy we ensure that the trace calls
use the correct kernel pointer, and that it happens right after the ioctl
call to the driver, so certainly inside the serialization lock.
In addition, we only trace if the call was successful.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Wade Farnsworth <wade_farnsworth@mentor.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Do not shift the already 7bit i2c address.
Print a message also for write+read transactions.
For write+read, print the read buffer correctly instead of using the write
buffer.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The two drivers LGDT3305 and TDA18271C2DD were not autoselected, so the
cx231xx_dvb module could not be loaded when MEDIA_SUBDRV_AUTOSELECT=y.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Add the missing unlock before return from function bcm2048_rds_fifo_receive()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Add a proper driver strength enum and use the same names in the platform
data as with adv7604.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
This timing must be supported by all HDMI equipment, so that's a
reasonable default.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The correct LLC DLL phase depends on the board layout, so this
should be part of the platform_data.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Tested-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Return 0 if the new timings are equal to the current timings as
it caused extra cp-loss/lock interrupts.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The free-run mode can be board-specific.
Also updated the platform_data in ezkit to ensure that what was the old
default value is now explicitly specified, so the behavior for that board
is unchanged.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Must clear timings before setting after test to recover.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Clear i2c_clients ptr when unregistered.
Warn if configured i2c-addr is zero.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The STDI block may measure wrong values, especially for lcvs and lcf.
If the driver can not find any valid timing, the STDI block is restarted
to measure the video timings again. The function will return an error,
but the restart of STDI will generate a new STDI interrupt and the format
detection process will restart.
Copied from adv7604.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
