Age | Commit message (Collapse) | Author |
|
Pull MMC update from Ulf Hansson:
"These patches are mainly updates for the mmci driver and have been
tested in linux-next.
Some ARM SoC related patches are also included and those have been
acked from the corresponding maintainers to go through my mmc tree.
Updates for mmci driver:
- Put the device into low power state at system suspend.
- Convert to the common mmc DT parser.
- Add missing DT bindings needed for ux500.
Updates for ARM ux500|u300:
- Convert to the common mmc DT bindings.
- Remove redundant board file for mmci platform data"
* tag 'mmc-v3.16-1' of git://git.linaro.org/people/ulf.hansson/mmc: (22 commits)
mmc: mmci: Enforce DMA configuration through DT
mmc: mmci: Enforce max frequency configuration through DT
mmc: mmci: Enforce mmc capabilities through DT
mmc: mmci: Enforce DT for signal direction and feedback clock
ARM: ux500: Remove redundant board file for mmci platform data
ARM: ux500: Add a vmmc regulator through DT for the poped eMMC for href
ARM: ux500: Add the mmc capabilities flags to DT
mmc: mmci: Enable MMC_CAP_CMD23
mmc: mmci: Mark the DT bindings for highspeed mode as deprecated
ARM: u300: Convert to the common mmc DT bindings for highspeed mode
ARM: nomadik: Convert to the common mmc DT bindings for highspeed mode
ARM: ux500: Convert to the common mmc DT bindings for highspeed mode
ARM: ux500: Add mmci signal directions and feeback clock in DT for href
mmc: mmci: Use the common mmc DT parser
mmc: mmci: Add DT bindings for feedback clock pin
mmc: mmci: Add DT bindings for signal direction
mmc: mmci: Update DT documentation
mmc: mmci: Convert to devm functions
mmc: mmci: Convert to the mmc gpio API
mmc: mmci: Put the device into low power state at system suspend
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi into next
Pull HSI (High Speed Syncronous Interface) changes from Sebastian Reichel:
"Please pull the following changes for the HSI subsystem, which I have
taken over from Carlos Chinea <carlos.chinea@nokia.com>.
The below patches have been worked on in the linux-omap mailinglist
for 10 months and are well tested in linux-next (have been in there
for more than two weeks) without any problems arising. Apart from
that potential regressions are very limited, because the subsystem is
not yet used by any platform in the mainline kernel.
- Add some documentation for the HSI subsystem
- Add Device Tree support for the HSI subsystem
- Add OMAP3 SSI driver (SSI is a legacy variant of HSI)
- Add Nokia N900 Modem driver (without speech support for now)"
* tag 'hsi-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi:
HSI: Introduce Nokia N900 modem driver
HSI: Introduce driver for SSI Protocol
Documentation: DT: omap-ssi binding documentation
HSI: Introduce OMAP SSI driver
HSI: Add common DT binding for HSI client devices
HSI: export method to (un)register clients
HSI: Add channel resource support to HSI clients
HSI: method to unregister clients from an hsi port
HSI: hsi-char: fix driver for multiport scenarios
MAINTAINERS: update HSI entry
Documentation: HSI: Add some general description for the HSI subsystem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp into next
Pull EDAC changes from Borislav Petkov:
"Just two small fixlets.
We have more in the pipe but we didn't get ready in time so more stuff
next time"
* tag 'edac_for_3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC: Fix MC scrub mode comparsion bug for correctable errors
EDAC, MCE, AMD: Remove leftover unused mask
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio into next
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v3.16 series.
There is a lot of action in the GPIO subsystem doing refactorings and
cleanups, almost as many deletions as insertions and minor feature
growth and no new drivers this time. Which is actually pretty nice.
Some GPIO-related stuff will come in through the pin control tree as
well.
Details:
- We are finalizing and fixing up the gpiochip irqchip helpers
bringing a helpful irqchip implementation into the gpiolib core and
avoiding duplicate code and, more importantly, duplicate bug fixes:
* Support for using the helpers with threaded interrupt handlers as
used on sleeping GPIO-irqchips
* Do not set up hardware triggers for edges or levels if the
default IRQ type is IRQ_TYPE_NONE - some drivers would exploit
the fact that you could get default initialization of the IRQ
type from the core at probe() but if no default type is set up
from the helper, we should not call the driver to configure
anything. Wait until a consumer requests the interrupt instead.
* Make the irqchip helpers put the GPIO irqs into their own lock
class. The GPIO irqchips can often emit (harmless, but annoying)
lockdep warnings about recursions when they are in fact just
cascaded IRQs. By putting them into their own lock class we help
the lockdep core to keep track of things.
* Switch the tc3589x GPIO expanders to use the irqchip helpers
* Switch the OMAP GPIO driver to use the irqchip helpers
* Add some documentation for the irqchip helpers
* select IRQ_DOMAIN when using the helpers since some platforms may
not be using this by default and it's a strict dependency.
- Continued GPIO descriptor refactoring:
* Remove the one instance of gpio_to_desc() from the device tree
code, making the OF GPIO code use GPIO descriptors only.
* Introduce gpiod_get_optional() and gpiod_get_optional_index()
akin to the similar regulator functions for cases where the use
of GPIO is optional and not strictly required.
* Make of_get_named_gpiod_flags() private - we do not want to
unnecessarily expose APIs to drivers that make the gpiolib harder
than necessary to maintain and refactor. Privatize this
function.
- Support "-gpio" suffix for the OF GPIO retrieveal path. We used to
look for "foo-gpios" or just "gpios" in device tree nodes, but it
turns out that some drivers with a single GPIO line will just state
"foo-gpio" (singularis). Sigh. Support this with a fallback
looking for it, as this simplifies driver code and handles it in
core code.
- Switch the ACPI GPIO core to fetch GPIOs with the *_cansleep
function variants as the GPIO operation region handler can sleep,
and shall be able to handle gpiochips that sleep.
- Tons of cleanups and janitorial work from Jingoo Han, Axel Lin,
Javier Martinez Canillas and Abdoulaye Berthe. Notably Jingoo cut
off a ton of pointless OOM messages.
- Incremental development and fixes for various drivers, nothing
really special here"
* tag 'gpio-v3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: select IRQ_DOMAIN for gpiolib irqchip helpers
gpio: pca953x: use gpiolib irqchip helpers
gpio: pcf857x: Add IRQF_SHARED when request irq
gpio: pcf857x: Avoid calling irq_domain_cleanup twice
gpio: mcp23s08: switch chip count to int
gpio: dwapb: use a second irq chip
gpio: ep93xx: Use devm_ioremap_resource()
gpio: mcp23s08: fixed count variable for devicetree probing
gpio: Add run-time dependencies to R-Car driver
gpio: pch: add slab include
Documentation / ACPI: Fix location of GPIO documentation
gpio / ACPI: use *_cansleep version of gpiod_get/set APIs
gpio: generic: add request function pointer
gpio-pch: Fix Kconfig dependencies
gpio: make of_get_named_gpiod_flags() private
gpio: gpioep93xx: use devm functions
gpio: janzttl: use devm function
gpio: timberdale: use devm functions
gpio: bt8xx: use devm function for memory allocation
gpio: include linux/bug.h in interface header
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip into next
Pull Xen updates from David Vrabel:
"xen: features and fixes for 3.16-rc0
- support foreign mappings in PVH domains (needed when dom0 is PVH)
- fix mapping high MMIO regions in x86 PV guests (this is also the
first half of removing the PAGE_IOMAP PTE flag).
- ARM suspend/resume support.
- ARM multicall support"
* tag 'stable/for-linus-3.16-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: map foreign pfns for autotranslated guests
xen-acpi-processor: Don't display errors when we get -ENOSYS
xen/pciback: Document the entry points for 'pcistub_put_pci_dev'
xen/pciback: Document when the 'unbind' and 'bind' functions are called.
xen-pciback: Document when we FLR an PCI device.
xen-pciback: First reset, then free.
xen-pciback: Cleanup up pcistub_put_pci_dev
x86/xen: do not use _PAGE_IOMAP in xen_remap_domain_mfn_range()
x86/xen: set regions above the end of RAM as 1:1
x86/xen: only warn once if bad MFNs are found during setup
x86/xen: compactly store large identity ranges in the p2m
x86/xen: fix set_phys_range_identity() if pfn_e > MAX_P2M_PFN
x86/xen: rename early_p2m_alloc() and early_p2m_alloc_middle()
xen/x86: set panic notifier priority to minimum
arm,arm64/xen: introduce HYPERVISOR_suspend()
xen: refactor suspend pre/post hooks
arm: xen: export HYPERVISOR_multicall to modules.
arm64: introduce virt_to_pfn
arm/xen: Remove definiition of virt_to_pfn in asm/xen/page.h
arm: xen: implement multicall hypercall support.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k into next
Pull m68k updates from Geert Uytterhoeven:
"Highlights:
- support for running kernels in fast TT-RAM instead of slow ST-RAM
on Atari
- multi-platform EARLY_PRINTK
- better support for machines with lots of RAM (think ARAnyM), and
for running kernels larger than 4 MiB (think multi-platform)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/hp300: Convert printk to pr_foo()
m68k/apollo: Convert printk to pr_foo()
m68k/amiga: Convert printk(foo to pr_foo()
m68k: Increase initial mapping to 8 or 16 MiB if possible
m68k: Update defconfigs for v3.15-rc2
m68k/atari: fix SCC initialization for debug console
m68k/mvme16x: Adopt common boot console
m68k: Multi-platform EARLY_PRINTK
m68k: Toward platform agnostic framebuffer debug logging
m68k/atari - atari_scsi: use correct virt/phys translation for DMA buffer
m68k/atari - ataflop: use correct virt/phys translation for DMA buffer
m68k/atari - atafb: convert allocation of fb ram to new interface
m68k/atari - stram: alloc ST-RAM pool even if kernel not in ST-RAM
|
|
Remove the option to provide DMA configuration as platform data,
enforce it through DT.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Pull drm fixes from Dave Airlie:
"Mostly quiet now:
i915:
fixing userspace visiblie issues, all stable marked
radeon:
one more pll fix, two crashers, one suspend/resume regression"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: Resume fbcon last
drm/radeon: only allocate necessary size for vm bo list
drm/radeon: don't allow RADEON_GEM_DOMAIN_CPU for command submission
drm/radeon: avoid crash if VM command submission isn't available
drm/radeon: lower the ref * post PLL maximum once more
drm/i915: Prevent negative relocation deltas from wrapping
drm/i915: Only copy back the modified fields to userspace from execbuffer
drm/i915: Fix dynamic allocation of physical handles
|
|
So a few people complained that
commit 177cf92de4aa97ec1435987e91696ed8b5023130
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Apr 1 22:14:59 2014 +0200
drm/crtc-helpers: fix dpms on logic
which was merged into 3.15-rc1, broke resume on radeons. Strangely git
bisect lead everyone to
commit 25f397a429dfa43f22c278d0119a60a343aa568f
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Jul 19 18:57:11 2013 +0200
drm/crtc-helper: explicit DPMS on after modeset
which was merged long ago and actually part of 3.14.
Digging deeper I've noticed (again) that the call to
drm_helper_resume_force_mode in the radeon resume handlers was a no-op
previously because everything gets shut down on suspend. radeon does
this with explicit calls to drm_helper_connector_dpms with DPMS_OFF.
But with 177c we now force the dpms state to ON, so suddenly
resume_force_mode actually forced the crtcs back on.
This is the intention of the change after all, the problem is that
radeon resumes the fbdev console layer _before_ restoring the display,
through calling fb_set_suspend. And fbcon does an immediate ->set_par,
which in turn causes the same forced mode restore to happen.
Two concurrent modeset operations didn't lead to happiness. Fix this
by delaying the fbcon resume until the end of the readeon resum
functions.
v2: Fix up a bit of the spelling fail.
References: https://lkml.org/lkml/2014/5/29/1043
References: https://lkml.org/lkml/2014/5/2/388
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=74751
Tested-by: Ken Moffat <zarniwhoop@ntlworld.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Ken Moffat <zarniwhoop@ntlworld.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem fixes from Dmitry Torokhov:
"A couple of driver/build fixups and also redone quirk for Synaptics
touchpads on Lenovo boxes (now using PNP IDs instead of DMI data to
limit number of quirks)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - change min/max quirk table to pnp-id matching
Input: synaptics - add a matches_pnp_id helper function
Input: synaptics - T540p - unify with other LEN0034 models
Input: synaptics - add min/max quirk for the ThinkPad W540
Input: ambakmi - request a shared interrupt for AMBA KMI devices
Input: pxa27x-keypad - fix generating scancode
Input: atmel-wm97xx - only build for AVR32
Input: fix ps2/serio module dependency
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire fix from Stefan Richter:
"A regression fix for the IEEE 1394 subsystem: re-enable IRQ-based
asynchronous request reception at addresses below 128 TB"
* tag 'firewire-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: revert to 4 GB RDMA, fix protocols using Memory Space
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device-mapper fixes from Mike Snitzer:
"A dm-cache stable fix to split discards on cache block boundaries
because dm-cache cannot yet handle discards that span cache blocks.
Really fix a dm-mpath LOCKDEP warning that was introduced in -rc1.
Add a 'no_space_timeout' control to dm-thinp to restore the ability to
queue IO indefinitely when no data space is available. This fixes a
change in behavior that was introduced in -rc6 where the timeout
couldn't be disabled"
* tag 'dm-3.15-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm mpath: really fix lockdep warning
dm cache: always split discards on cache block boundaries
dm thin: add 'no_space_timeout' dm-thin-pool module param
|
|
No need to always allocate the theoretical maximum here.
Signed-off-by: Christian König <christian.koenig@amd.com>
|
|
It hangs the hardware.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
|
|
Signed-off-by: Christian König <christian.koenig@amd.com>
CC: stable@vger.kernel.org
|
|
Let's be conservative and use 100 here until we find something better.
Bugs: https://bugzilla.kernel.org/show_bug.cgi?id=75241
Signed-off-by: Christian König <christian.koenig@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are three stable-candidate fixes, one for the ACPI thermal
driver and two for cpufreq drivers.
Specifics:
- A workqueue is destroyed too early during the ACPI thermal driver
module unload which leads to a NULL pointer dereference in the
driver's remove callback. Fix from Aaron Lu.
- A wrong argument is passed to devm_regulator_get_optional() in the
probe routine of the cpu0 cpufreq driver which leads to resource
leaks if the driver is unbound from the cpufreq platform device.
Fix from Lucas Stach.
- A lock is missing in cpufreq_governor_dbs() which leads to memory
corruption and NULL pointer dereferences during system
suspend/resume, for example. Fix from Bibek Basu"
* tag 'pm+acpi-3.15-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / thermal: fix workqueue destroy order
cpufreq: cpu0: drop wrong devm usage
cpufreq: remove race while accessing cur_policy
|
|
git://git.linaro.org/people/mike.turquette/linux
Pull clock fixes from Mike Turquette:
"Small number of user-visible regression fixes for clock drivers.
There is a memory leak fix for an ST platform, an infinite Loop Of
Doom fix for the recent changes to the basic clock divider (hopefully
the last fix for those recent changes) and some Tegra PLL changes
which keep PCI from being hosed on that platform"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux:
clk: st: Fix memory leak
clk: divider: Fix table round up function
clk: tegra: Fix enabling of PLLE
clk: tegra: Introduce divider mask and shift helpers
clk: tegra: Fix PLLE programming
|
|
These helpers depend on the IRQ_DOMAIN so select it explicitly,
as it will not be present on all platforms such as Intel
desktops and laptops using Intel-MID.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Undo a feature introduced in v3.14 by commit fcd46b34425d
"firewire: Enable remote DMA above 4 GB". That change raised the
minimum address at which protocol drivers and user programs can register
for request reception from 0x0001'0000'0000 to 0x8000'0000'0000.
It turned out that at least one vendor-specific protocol exists which
uses lower addresses: https://bugzilla.kernel.org/show_bug.cgi?id=76921
For the time being, revert most of commit fcd46b34425d so that affected
protocols work like with kernel v3.13 and before. Just keep the valid
documentation parts from the regressing commit, and the ability to
identify controllers which could be programmed to accept >32 bit
physical DMA addresses. The rest of fcd46b34425d should probably be
brought back as an optional instead of default feature.
Reported-by: Fabien Spindler <fabien.spindler@inria.fr>
Cc: <stable@vger.kernel.org> # 3.14+
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
This switches the PCA953x driver over to using the gpiolib irqchip
helpers to handle the threaded interrups cascaded off this
GPIO chip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It's quite possible that multiple pcf857x can be hooked up
to the same interrupt line with the processor. So add IRQF_SHARED
in request irq..
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Currently irq_domain_cleanup is called twice if irq_domain_init fails.
This causes the following crash.
Unable to handle kernel paging request at virtual address 00100104
pgd = c0004000
[00100104] *pgd=00000000
Internal error: Oops: 805 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u4:0 Not tainted 3.12.15-01889-gedd10a8-dirty #4
Workqueue: deferwq deferred_probe_work_func
task: ed0ee800 ti: ed116000 task.ti: ed116000
PC is at irq_domain_remove+0x3c/0x8c
LR is at 0x0
pc : [<c0089734>] lr : [<00000000>] psr: a0000013
sp : ed117b50 ip : 00100100 fp : ed117b64
r10: ed5d1a04 r9 : 00000008 r8 : 00000000
r7 : ffffffea r6 : ed5d1a20 r5 : ed5d1a00 r4 : ed5e7540
r3 : 00200200 r2 : 00100100 r1 : c08aa180 r0 : 00200200
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c53c7d Table: 8000406a DAC: 00000017
Process kworker/u4:0 (pid: 6, stack limit = 0xed116248)
Stack: (0xed117b50 to 0xed118000)
7b40: 0000016b ed5d5f10 ed117b74 ed117b68
7b60: c02c8910 c0089704 ed117bb4 ed117b78 c02c8e14 c02c8900 ed5d1a04 ed5d4e80
...
<snip>
...
fe0: 00000000 00000000 00000000 00000000 00000013 00000000 384a13ea 1590210a
Backtrace:
[<c00896f8>] (irq_domain_remove+0x0/0x8c) from [<c02c8910>] (pcf857x_irq_domain_cleanup+0x1c/0x20)
r4:ed5d5f10 r3:0000016b
[<c02c88f4>] (pcf857x_irq_domain_cleanup+0x0/0x20) from [<c02c8e14>] (pcf857x_probe+0x2a8/0x364)
[<c02c8b6c>] (pcf857x_probe+0x0/0x364) from [<c04787ac>] (i2c_device_probe+0x80/0xc0)
[<c047872c>] (i2c_device_probe+0x0/0xc0) from [<c036c33c>] (driver_probe_device+0x104/0x240)
r6:00000000 r5:ed5d1a20 r4:c08c709c r3:c047872c
[<c036c238>] (driver_probe_device+0x0/0x240) from [<c036c558>] (__device_attach+0x48/0x4c)
r7:ed4fc480 r6:c036c510 r5:ed5d1a20 r4:c0866bb8
[<c036c510>] (__device_attach+0x0/0x4c) from [<c036a6d8>] (bus_for_each_drv+0x4c/0x94)
r5:ed5d1a20 r4:00000000
[<c036a68c>] (bus_for_each_drv+0x0/0x94) from [<c036c1f4>] (device_attach+0x78/0x90)
r6:c087fe50 r5:ed5d1a54 r4:ed5d1a20
[<c036c17c>] (device_attach+0x0/0x90) from [<c036b76c>] (bus_probe_device+0x8c/0xb4)
r6:c087fe50 r5:ed5d1a20 r4:ed5d1a20 r3:ed17e1c0
[<c036b6e0>] (bus_probe_device+0x0/0xb4) from [<c0369888>] (device_add+0x34c/0x624)
r6:ed5d1a28 r5:00000000 r4:ed5d1a20 r3:fffffffe
[<c036953c>] (device_add+0x0/0x624) from [<c0369b7c>] (device_register+0x1c/0x20)
...
<snip>
...
[<c0060844>] (process_one_work+0x0/0x37c) from [<c0061040>] (worker_thread+0x13c/0x3c4)
[<c0060f04>] (worker_thread+0x0/0x3c4) from [<c00670ec>] (kthread+0xac/0xb8)
[<c0067040>] (kthread+0x0/0xb8) from [<c00148b8>] (ret_from_fork+0x14/0x3c)
r7:00000000 r6:00000000 r5:c0067040 r4:ed105d20
Code: e59fc04c e591e000 e59f0048 e154000e (e5823004)
---[ end trace 59dd1e90032c4217 ]---
Signed-off-by: George Cherian <george.cherian@ti.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit 3e3bed913e8bbd78f38cefd5d575475f45c05dd0
"gpio: mcp23s08: fixed count variable for devicetree probing"
introduced a loop check to see if the number of chips were
unconsistent and going below zero counting downwards, but
this requires the counting variable to be able to be
negative, so switch the variable from unsigned to int.
Cc: Michael Stickel <ms@mycable.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://nv-tegra.nvidia.com/user/pdeschrijver/linux into clk-fixes
PLLE fixes for 3.15
|
|
Pull virtio_blk fix from Jens Axboe:
"There's a start/stop queue race in virtio_blk, which causes stalls and
erratic behaviour for some. I've had this queued up for 3.16 for a
while, but I think we should push it into the current series as well.
So I cherry picked the commit and added a stable marker as well, so it
can propagate down"
* 'for-linus' of git://git.kernel.dk/linux-block:
virtio_blk: fix race between start and stop queue
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull two timer fixes from Thomas Gleixner:
"Two small fixlets for ARM SoC clocksource drivers:
- avoid calling functions which might sleep from interrupt [disabled]
context in tcb_clksrc used on Atmel SoCs
- use irq_force_affinity() to pin the per cpu timer interrupt on a
not yet online cpu in the SiRFprimaII driver"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: tcb_clksrc: Make tc_mode interrupt safe
clocksource: marco: Fix the affinity set for local timer of CPU1
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fix from Linus Walleij:
"A single last pinctrl fix for the v3.15 series: the vt8500 driver was
failing to update the output value when the combined set direction
output and set value was executed"
* tag 'pinctrl-v3.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: vt8500: Ensure value reg is updated when setting direction
|
|
Pull slave-dmaengine fixes from Vinod Koul:
"We have three small fixes.
First one from Andy reverts the devm_request irq as we need to ensure
the tasklet is killed after irq is freed, so we need to do free irq in
our code. Other two from Arnd are fixing the compilation issue in
omap and sa11x0 drivers with ARM randconfigs"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: sa11x0: remove broken #ifdef
dmaengine: omap: hide filter_fn for built-in drivers
dmaengine: dw: went back to plain {request,free}_irq() calls
|
|
lockdep complains about a circular locking. And indeed, we need to
release the lock before calling dm_table_run_md_queue_async().
As such, commit 4cdd2ad ("dm mpath: fix lock order inconsistency in
multipath_ioctl") must also be reverted in addition to fixing the
lock order in the other dm_table_run_md_queue_async() callers.
Reported-by: Bart van Assche <bvanassche@acm.org>
Tested-by: Bart van Assche <bvanassche@acm.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
When there isn't enough vring descriptor for adding to vq,
blk-mq will be put as stopped state until some of pending
descriptors are completed & freed.
Unfortunately, the vq's interrupt may come just before
blk-mq's BLK_MQ_S_STOPPED flag is set, so the blk-mq will
still be kept as stopped even though lots of descriptors
are completed and freed in the interrupt handler. The worst
case is that all pending descriptors are freed in the
interrupt handler, and the queue is kept as stopped forever.
This patch fixes the problem by starting/stopping blk-mq
with holding vq_lock.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
Conflicts:
drivers/block/virtio_blk.c
|
|
The DM cache target cannot cope with discards that span multiple cache
blocks, so each discard bio that spans more than one cache block must
get split by the DM core.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # v3.9+
|
|
Right new have one irq chip running always in level mode. It would nicer
to have two irq chips where one is handling level type interrupts and
the other one is doing edge interrupts. So we can have at runtime two users
where one is using edge and the other level.
Acked-by: Alan Tull <delicious.quinoa@gmail.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use devm_ioremap_resource() because devm_request_and_ioremap() is
obsoleted by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fixed missing increase of count variable for devicetree path in driver
probing.
The gpio-mcp23s08 driver has two paths for getting the platform
registration information. One for the classic platform initialization
and one for openfirmware devicetree based initialization. The devicetree
based path is missing the increase of the count variable, which results
in the count variable to become negative in the later use, where it is
decreased. The count variable is used as an index into a vector. This
results in accessing invalid memory space and can result in an exception.
Tested this with an AM3352 SoC with two mcp23s17 on two chip selects as
well as on a shared chip select.
Signed-off-by: Michael Stickel <ms@mycable.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Renesas R-Car GPIO driver is only useful on shmobile unless build
testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Magnus Damm <damm@opensource.se>
Cc: Alexandre Courbot <gnurou@gmail.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
After change 3ff35cbcfa4bc7d7dbdd0279e32ea677567ded02
"gpio-pch: Fix Kconfig dependencies"
which enabled COMPILE_TEST as an alternative for the PCH
driver, we get build failures like this:
drivers/gpio/gpio-pch.c: In function 'pch_gpio_probe':
drivers/gpio/gpio-pch.c:359:2: error: implicit declaration
of function 'kzalloc' [-Werror=implicit-function-declaration]
drivers/gpio/gpio-pch.c:359:7: warning: assignment makes
pointer from integer without a cast [enabled by default]
drivers/gpio/gpio-pch.c:442:2: error: implicit declaration
of function 'kfree' [-Werror=implicit-function-declaration]
Fix this by including <linux/slab.h> explicitly.
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is pure evil. Userspace, I'm looking at you SNA, repacks batch
buffers on the fly after generation as they are being passed to the
kernel for execution. These batches also contain self-referenced
relocations as a single buffer encompasses the state commands, kernels,
vertices and sampler. During generation the buffers are placed at known
offsets within the full batch, and then the relocation deltas (as passed
to the kernel) are tweaked as the batch is repacked into a smaller buffer.
This means that userspace is passing negative relocations deltas, which
subsequently wrap to large values if the batch is at a low address. The
GPU hangs when it then tries to use the large value as a base for its
address offsets, rather than wrapping back to the real value (as one
would hope). As the GPU uses positive offsets from the base, we can
treat the relocation address as the minimum address read by the GPU.
For the upper bound, we trust that userspace will not read beyond the
end of the buffer.
So, how do we fix negative relocations from wrapping? We can either
check that every relocation looks valid when we write it, and then
position each object such that we prevent the offset wraparound, or we
just special-case the self-referential behaviour of SNA and force all
batches to be above 256k. Daniel prefers the latter approach.
This fixes a GPU hang when it tries to use an address (relocation +
offset) greater than the GTT size. The issue would occur quite easily
with full-ppgtt as each fd gets its own VM space, so low offsets would
often be handed out. However, with the rearrangement of the low GTT due
to capturing the BIOS framebuffer, it is already affecting kernels 3.15
onwards. I think only IVB+ is susceptible to this bug, but the workaround
should only kick in rarely, so it seems sensible to always apply it.
v3: Use a bias for batch buffers to prevent small negative delta relocations
from wrapping.
v4 from Daniel:
- s/BIAS/BATCH_OFFSET_BIAS/
- Extract eb_vma_misplaced/i915_vma_misplaced since the conditions
were growing rather cumbersome.
- Add a comment to eb_get_batch explaining why we do this.
- Apply the batch offset bias everywhere but mention that we've only
observed it on gen7 gpus.
- Drop PIN_OFFSET_FIX for now, that slipped in from a feature patch.
v5: Add static to eb_get_batch, spotted by 0-day tester.
Testcase: igt/gem_bad_reloc
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=78533
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v3)
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We only want to modifiy a single field in the userspace view of the
execbuffer command buffer, so explicitly change that rather than copy
everything back again.
This serves two purposes:
1. The single fields are much cheaper to copy (constant size so the
copy uses special case code) and much smaller than the whole array.
2. We modify the array for internal use that need to be masked from
the user.
Note: We need this backported since without it the next bugfix will
blow up when userspace recycles batchbuffers and relocations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
A single object may be referenced by multiple registers fundamentally
breaking the static allotment of ids in the current design. When the
object is used the second time, the physical address of the first
assignment is relinquished and a second one granted. However, the
hardware is still reading (and possibly writing) to the old physical
address now returned to the system. Eventually hilarity will ensue, but
in the short term, it just means that cursors are broken when using more
than one pipe.
v2: Fix up leak of pci handle when handling an error during attachment,
and avoid a double kmap/kunmap. (Ville)
Rebase against -fixes.
v3: And fix the error handling added in v2 (Ville)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77351
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Most of the affected models share pnp-ids for the touchpad. So switching
to pnp-ids give us 2 advantages:
1) It shrinks the quirk list
2) It will lower the new quirk addition frequency, ie the recently added W540
quirk would not have been necessary since it uses the same LEN0034 pnp ids
as other models already added before it
As an added bonus it actually puts the quirk on the actual psmouse, rather
then on the machine, which is technically more correct.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This is a preparation patch for simplifying the min/max quirk table.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The T540p has a touchpad with pnp-id LEN0034, all the models with this
pnp-id have the same min/max values, except the T540p where the values are
slightly off. Fix them to be identical.
This is a preparation patch for simplifying the quirk table.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
* pm-cpufreq:
cpufreq: cpu0: drop wrong devm usage
cpufreq: remove race while accessing cur_policy
* acpi-thermal:
ACPI / thermal: fix workqueue destroy order
|
|
With the kernel running from FastRAM instead of ST-RAM, none of ST-RAM is
mapped by mem_init, and DMA-addressable buffer must be mapped by ioremap.
Use platform specific virt/phys translation helpers for this case.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
With the kernel running from FastRAM instead of ST-RAM, none of ST-RAM is
mapped by mem_init, and DMA-addressable buffer must be mapped by ioremap.
Use platform specific virt/phys translation helpers for this case.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
The new atari_stram_alloc interface returns kernel virtual addresses
even if the kernel runs in FastRAM. These addresses are not
guaranteed to be identical with the physical addresses. Since ST-RAM
mappings have not been set up by mem_init, virt_to_phys() and its
cousin do not work and the atari_stram_to_phys() etc. helpers must
be used to determine physical addresses.
fb.fix->smem_start needs physical addresses, fb.par->screen_base
needs virtual addresses. Take care of the virt-to-phys conversion
both on fb init and par changes.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
When the thermal module is to be removed, we should destroy the wq
acpi_thermal_pm_queue after the ACPI driver's remove callback is
executed as we will need to flush the workqueue there, or a NULL pointer
access will be hit.
Reported-and-tested-by: Kui Zhang <kuizhang@gmail.com>
References: http://www.spinics.net/lists/kernel/msg1747251.html
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull hwmon subsystem fixes from Jean Delvare.
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (ntc_thermistor) Fix OF device ID mapping
hwmon: (ntc_thermistor) Fix dependencies
hwmon: Document temp[1-*]_min_hyst sysfs attribute
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull single scsi fix from James Bottomley:
"This is a single fix for a bug exposed by a sysfs change in 3.13 which
now causes libsas to trigger a warn on in device removal"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] scsi_transport_sas: move bsg destructor into sas_rphy_remove
|