Age | Commit message (Collapse) | Author |
|
commit fd63a8903a2c40425a9811c3371dd4d0f42c0ad3 upstream.
On our at91sam9260 based board the usart0 and usart1 ports report
their versions (ATMEL_US_VERSION) as 0x10302. This version is not
included in the current checks in the driver.
Signed-off-by: Jonas Danielsson <jonas@orbital-systems.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7842055bfce4bf0170d0f61df8b2add8399697be upstream.
When the TTY buffers fill up to the configured maximum, a system lockup
occurs:
[ 598.820128] INFO: rcu_preempt detected stalls on CPUs/tasks:
[ 598.825796] 0-...!: (1 GPs behind) idle=5a6/2/0 softirq=1974/1974 fqs=1
[ 598.832577] (detected by 3, t=62517 jiffies, g=296, c=295, q=126)
[ 598.838755] Task dump for CPU 0:
[ 598.841977] swapper/0 R running task 0 0 0 0x00000022
[ 598.849023] Call trace:
[ 598.851476] __switch_to+0x98/0xb0
[ 598.854870] (null)
This can be prevented by doing a dummy read of the RX data register.
This issue affects both HSCIF and SCIF ports. Reported for R-Car H3 ES2.0;
reproduced and fixed on H3 ES1.1. Probably affects other R-Car platforms
as well.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable <stable@vger.kernel.org>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 063b36d6b0ad74c748d536f5cb47bac2f850a0fa upstream.
Current code manually allocate an fcport structure that is not properly
initialize. Replace kzalloc with qla2x00_alloc_fcport, so that all
fields are initialized. Also set set scan flag to port found
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a51a0c8d213594bc094cb8e54aad0cb6d7f7b9a6 upstream.
Similar to commit 714fb87e8bc0 ("ubi: Fix race condition between ubi
device creation and udev"), we should make the volume active before
registering it.
Signed-off-by: Clay McClure <clay@daemons.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f2c61f98e0b5f8b53b8fb860e5dcdd661bde7d0b upstream.
The below mentioned fix contains a small but severe bug,
fix it to make the driver work again.
Fixes: 3538aa6ecfb2 ("[media] tc358743: fix register i2c_rd/wr functions")
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9dd46c02532a6bed6240101ecf4bbc407f8c6adf upstream.
There is no need to tread the same register twice in a row.
Fixes: ea4348c8462a ("Input: tca8418_keypad - hide gcc-4.9 -Wmaybe-un ...")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aeebc6ba88ba3758ad95467ff6191fabf2074c13 upstream.
The new hpwdt_my_nmi() function is used conditionally, which produces
a harmless warning in some configurations:
drivers/watchdog/hpwdt.c:478:12: error: 'hpwdt_my_nmi' defined but not used [-Werror=unused-function]
This moves it inside of the #ifdef that protects its caller, to silence
the warning.
Fixes: 621174a92851 ("watchdog: hpwdt: Check source of NMI")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 838534e50e2e5c1e644e30ab6cb28da88eb31368 upstream.
Do not claim the NMI (i.e. return NMI_DONE) if the source of
the NMI isn't the iLO watchdog or debug.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c42cbe41727a138905a28f8e0b00c147be77ee93 upstream.
This corrects:
commit cce78da76601 ("watchdog: hpwdt: Add check for UEFI bits")
The test on HPE SMBIOS extension type 219 record "Misc Features"
bits for UEFI support is incorrect. The definition of the Misc Features
bits in the HPE SMBIOS OEM Extensions specification (and related
firmware) was changed to use a different pair of bits to
represent UEFI supported. Howerver, a corresponding change
to Linux was missed.
Current code/platform work because the iCRU test is working.
But purpose of cce78da766 is to ensure correct functionality
on future systems where iCRU isn't supported.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 86755b7a96faed57f910f9e6b8061e019ac1ec08 upstream.
This can happen e.g. during disk cloning.
This is an incomplete fix: it does not catch duplicate UUIDs earlier
when things are still unattached. It does not unregister the device.
Further changes to cope better with this are planned but conflict with
Coly's ongoing improvements to handling device errors. In the meantime,
one can manually stop the device after this has happened.
Attempts to attach a duplicate device result in:
[ 136.372404] loop: module loaded
[ 136.424461] bcache: register_bdev() registered backing device loop0
[ 136.424464] bcache: bch_cached_dev_attach() Tried to attach loop0 but duplicate UUID already attached
My test procedure is:
dd if=/dev/sdb1 of=imgfile bs=1024 count=262144
losetup -f imgfile
Signed-off-by: Michael Lyle <mlyle@lyle.org>
Reviewed-by: Tang Junhui <tang.junhui@zte.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1d037577c323e5090ce281e96bc313ab2eee5be2 upstream.
The following commit:
commit aa4d86163e4e ("block: loop: switch to VFS ITER_BVEC")
replaced __do_lo_send_write(), which used ITER_KVEC iterators, with
lo_write_bvec() which uses ITER_BVEC iterators. In this change, though,
the WRITE flag was lost:
- iov_iter_kvec(&from, ITER_KVEC | WRITE, &kvec, 1, len);
+ iov_iter_bvec(&i, ITER_BVEC, bvec, 1, bvec->bv_len);
This flag is necessary for the DAX case because we make decisions based on
whether or not the iterator is a READ or a WRITE in dax_iomap_actor() and
in dax_iomap_rw().
We end up going through this path in configurations where we combine a PMEM
device with 4k sectors, a loopback device and DAX. The consequence of this
missed flag is that what we intend as a write actually turns into a read in
the DAX code, so no data is ever written.
The very simplest test case is to create a loopback device and try and
write a small string to it, then hexdump a few bytes of the device to see
if the write took. Without this patch you read back all zeros, with this
you read back the string you wrote.
For XFS this causes us to fail or panic during the following xfstests:
xfs/074 xfs/078 xfs/216 xfs/217 xfs/250
For ext4 we have a similar issue where writes never happen, but we don't
currently have any xfstests that use loopback and show this issue.
Fix this by restoring the WRITE flag argument to iov_iter_bvec(). This
causes the xfstests to all pass.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
Fixes: commit aa4d86163e4e ("block: loop: switch to VFS ITER_BVEC")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ea4f7bd2aca9f68470e9aac0fc9432fd180b1fe7 upstream.
If matrix_keypad_stop() is executing and the keypad interrupt is triggered,
disable_row_irqs() may be called by both matrix_keypad_interrupt() and
matrix_keypad_stop() at the same time, causing interrupts to be disabled
twice and the keypad being "stuck" after resuming.
Take lock when setting keypad->stopped to ensure that ISR will not race
with matrix_keypad_stop() disabling interrupts.
Signed-off-by: Zhang Bo <zbsdta@126.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 545b0bcde7fbd3ee408fa842ea0731451dc4bd0a upstream.
Always set the graphics values to the max for the
asic type. E.g., some 1 RB chips are actually 1 RB chips,
others are actually harvested 2 RB chips.
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=99353
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0b58d90f89545e021d188c289fa142e5ff9e708b upstream.
Always set the graphics values to the max for the
asic type. E.g., some 1 RB chips are actually 1 RB chips,
others are actually harvested 2 RB chips.
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=99353
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1bced75f4ab04bec55aecb57d99435dc6d0ae5a0 upstream.
it is required if a platform supports PCIe root complex
core voltage reduction. After receiving this notification,
SBIOS can apply default PCIe root complex power policy.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aa0aad57909eb321746325951d66af88a83bc956 upstream.
amdgpu's ->runtime_suspend hook calls drm_kms_helper_poll_disable(),
which waits for the output poll worker to finish if it's running.
The output poll worker meanwhile calls pm_runtime_get_sync() in
amdgpu's ->detect hooks, which waits for the ongoing suspend to finish,
causing a deadlock.
Fix by not acquiring a runtime PM ref if the ->detect hooks are called
in the output poll worker's context. This is safe because the poll
worker is only enabled while runtime active and we know that
->runtime_suspend waits for it to finish.
Fixes: d38ceaf99ed0 ("drm/amdgpu: add core driver (v4)")
Cc: stable@vger.kernel.org # v4.2+: 27d4ee03078a: workqueue: Allow retrieval of current task's work struct
Cc: stable@vger.kernel.org # v4.2+: 25c058ccaf2e: drm: Allow determining if current task is output poll worker
Cc: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Mike Lothian <mike@fireburn.co.uk>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/4c9bf72aacae1eef062bd134cd112e0770a7f121.1518338789.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 15734feff2bdac24aa3266c437cffa42851990e3 upstream.
radeon's ->runtime_suspend hook calls drm_kms_helper_poll_disable(),
which waits for the output poll worker to finish if it's running.
The output poll worker meanwhile calls pm_runtime_get_sync() in
radeon's ->detect hooks, which waits for the ongoing suspend to finish,
causing a deadlock.
Fix by not acquiring a runtime PM ref if the ->detect hooks are called
in the output poll worker's context. This is safe because the poll
worker is only enabled while runtime active and we know that
->runtime_suspend waits for it to finish.
Stack trace for posterity:
INFO: task kworker/0:3:31847 blocked for more than 120 seconds
Workqueue: events output_poll_execute [drm_kms_helper]
Call Trace:
schedule+0x3c/0x90
rpm_resume+0x1e2/0x690
__pm_runtime_resume+0x3f/0x60
radeon_lvds_detect+0x39/0xf0 [radeon]
output_poll_execute+0xda/0x1e0 [drm_kms_helper]
process_one_work+0x14b/0x440
worker_thread+0x48/0x4a0
INFO: task kworker/2:0:10493 blocked for more than 120 seconds.
Workqueue: pm pm_runtime_work
Call Trace:
schedule+0x3c/0x90
schedule_timeout+0x1b3/0x240
wait_for_common+0xc2/0x180
wait_for_completion+0x1d/0x20
flush_work+0xfc/0x1a0
__cancel_work_timer+0xa5/0x1d0
cancel_delayed_work_sync+0x13/0x20
drm_kms_helper_poll_disable+0x1f/0x30 [drm_kms_helper]
radeon_pmops_runtime_suspend+0x3d/0xa0 [radeon]
pci_pm_runtime_suspend+0x61/0x1a0
vga_switcheroo_runtime_suspend+0x21/0x70
__rpm_callback+0x32/0x70
rpm_callback+0x24/0x80
rpm_suspend+0x12b/0x640
pm_runtime_work+0x6f/0xb0
process_one_work+0x14b/0x440
worker_thread+0x48/0x4a0
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94147
Fixes: 10ebc0bc0934 ("drm/radeon: add runtime PM support (v2)")
Cc: stable@vger.kernel.org # v3.13+: 27d4ee03078a: workqueue: Allow retrieval of current task's work struct
Cc: stable@vger.kernel.org # v3.13+: 25c058ccaf2e: drm: Allow determining if current task is output poll worker
Cc: Ismo Toijala <ismo.toijala@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Dave Airlie <airlied@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/64ea02c44f91dda19bc563902b97bbc699040392.1518338789.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d61a5c1063515e855bedb1b81e20e50b0ac3541e upstream.
nouveau's ->runtime_suspend hook calls drm_kms_helper_poll_disable(),
which waits for the output poll worker to finish if it's running.
The output poll worker meanwhile calls pm_runtime_get_sync() in
nouveau_connector_detect() which waits for the ongoing suspend to finish,
causing a deadlock.
Fix by not acquiring a runtime PM ref if nouveau_connector_detect() is
called in the output poll worker's context. This is safe because
the poll worker is only enabled while runtime active and we know that
->runtime_suspend waits for it to finish.
Other contexts calling nouveau_connector_detect() do require a runtime
PM ref, these comprise:
status_store() drm sysfs interface
->fill_modes drm callback
drm_fb_helper_probe_connector_modes()
drm_mode_getconnector()
nouveau_connector_hotplug()
nouveau_display_hpd_work()
nv17_tv_set_property()
Stack trace for posterity:
INFO: task kworker/0:1:58 blocked for more than 120 seconds.
Workqueue: events output_poll_execute [drm_kms_helper]
Call Trace:
schedule+0x28/0x80
rpm_resume+0x107/0x6e0
__pm_runtime_resume+0x47/0x70
nouveau_connector_detect+0x7e/0x4a0 [nouveau]
nouveau_connector_detect_lvds+0x132/0x180 [nouveau]
drm_helper_probe_detect_ctx+0x85/0xd0 [drm_kms_helper]
output_poll_execute+0x11e/0x1c0 [drm_kms_helper]
process_one_work+0x184/0x380
worker_thread+0x2e/0x390
INFO: task kworker/0:2:252 blocked for more than 120 seconds.
Workqueue: pm pm_runtime_work
Call Trace:
schedule+0x28/0x80
schedule_timeout+0x1e3/0x370
wait_for_completion+0x123/0x190
flush_work+0x142/0x1c0
nouveau_pmops_runtime_suspend+0x7e/0xd0 [nouveau]
pci_pm_runtime_suspend+0x5c/0x180
vga_switcheroo_runtime_suspend+0x1e/0xa0
__rpm_callback+0xc1/0x200
rpm_callback+0x1f/0x70
rpm_suspend+0x13c/0x640
pm_runtime_work+0x6e/0x90
process_one_work+0x184/0x380
worker_thread+0x2e/0x390
Bugzilla: https://bugs.archlinux.org/task/53497
Bugzilla: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=870523
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70388#c33
Fixes: 5addcf0a5f0f ("nouveau: add runtime PM support (v0.9)")
Cc: stable@vger.kernel.org # v3.12+: 27d4ee03078a: workqueue: Allow retrieval of current task's work struct
Cc: stable@vger.kernel.org # v3.12+: 25c058ccaf2e: drm: Allow determining if current task is output poll worker
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/b7d2cbb609a80f59ccabfdf479b9d5907c603ea1.1518338789.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 25c058ccaf2ebbc3e250ec1e199e161f91fe27d4 upstream.
Introduce a helper to determine if the current task is an output poll
worker.
This allows us to fix a long-standing deadlock in several DRM drivers
wherein the ->runtime_suspend callback waits for the output poll worker
to finish and the worker in turn calls a ->detect callback which waits
for runtime suspend to finish. The ->detect callback is invoked from
multiple call sites and waiting for runtime suspend to finish is the
correct thing to do except if it's executing in the context of the
worker.
v2: Expand kerneldoc to specifically mention deadlock between
output poll worker and autosuspend worker as use case. (Lyude)
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/3549ce32e7f1467102e70d3e9cbf70c46bfe108e.1518593424.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1514839b366417934e2f1328edb50ed1e8a719f5 upstream.
This patch fixes NULL pointer crash due to active timer running for abort
IOCB.
From crash dump analysis it was discoverd that get_next_timer_interrupt()
encountered a corrupted entry on the timer list.
#9 [ffff95e1f6f0fd40] page_fault at ffffffff914fe8f8
[exception RIP: get_next_timer_interrupt+440]
RIP: ffffffff90ea3088 RSP: ffff95e1f6f0fdf0 RFLAGS: 00010013
RAX: ffff95e1f6451028 RBX: 000218e2389e5f40 RCX: 00000001232ad600
RDX: 0000000000000001 RSI: ffff95e1f6f0fdf0 RDI: 0000000001232ad6
RBP: ffff95e1f6f0fe40 R8: ffff95e1f6451188 R9: 0000000000000001
R10: 0000000000000016 R11: 0000000000000016 R12: 00000001232ad5f6
R13: ffff95e1f6450000 R14: ffff95e1f6f0fdf8 R15: ffff95e1f6f0fe10
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
Looking at the assembly of get_next_timer_interrupt(), address came
from %r8 (ffff95e1f6451188) which is pointing to list_head with single
entry at ffff95e5ff621178.
0xffffffff90ea307a <get_next_timer_interrupt+426>: mov (%r8),%rdx
0xffffffff90ea307d <get_next_timer_interrupt+429>: cmp %r8,%rdx
0xffffffff90ea3080 <get_next_timer_interrupt+432>: je 0xffffffff90ea30a7 <get_next_timer_interrupt+471>
0xffffffff90ea3082 <get_next_timer_interrupt+434>: nopw 0x0(%rax,%rax,1)
0xffffffff90ea3088 <get_next_timer_interrupt+440>: testb $0x1,0x18(%rdx)
crash> rd ffff95e1f6451188 10
ffff95e1f6451188: ffff95e5ff621178 ffff95e5ff621178 x.b.....x.b.....
ffff95e1f6451198: ffff95e1f6451198 ffff95e1f6451198 ..E.......E.....
ffff95e1f64511a8: ffff95e1f64511a8 ffff95e1f64511a8 ..E.......E.....
ffff95e1f64511b8: ffff95e77cf509a0 ffff95e77cf509a0 ...|.......|....
ffff95e1f64511c8: ffff95e1f64511c8 ffff95e1f64511c8 ..E.......E.....
crash> rd ffff95e5ff621178 10
ffff95e5ff621178: 0000000000000001 ffff95e15936aa00 ..........6Y....
ffff95e5ff621188: 0000000000000000 00000000ffffffff ................
ffff95e5ff621198: 00000000000000a0 0000000000000010 ................
ffff95e5ff6211a8: ffff95e5ff621198 000000000000000c ..b.............
ffff95e5ff6211b8: 00000f5800000000 ffff95e751f8d720 ....X... ..Q....
ffff95e5ff621178 belongs to freed mempool object at ffff95e5ff621080.
CACHE NAME OBJSIZE ALLOCATED TOTAL SLABS SSIZE
ffff95dc7fd74d00 mnt_cache 384 19785 24948 594 16k
SLAB MEMORY NODE TOTAL ALLOCATED FREE
ffffdc5dabfd8800 ffff95e5ff620000 1 42 29 13
FREE / [ALLOCATED]
ffff95e5ff621080 (cpu 6 cache)
Examining the contents of that memory reveals a pointer to a constant string
in the driver, "abort\0", which is set by qla24xx_async_abort_cmd().
crash> rd ffffffffc059277c 20
ffffffffc059277c: 6e490074726f6261 0074707572726574 abort.Interrupt.
ffffffffc059278c: 00676e696c6c6f50 6920726576697244 Polling.Driver i
ffffffffc059279c: 646f6d207325206e 6974736554000a65 n %s mode..Testi
ffffffffc05927ac: 636976656420676e 786c252074612065 ng device at %lx
ffffffffc05927bc: 6b63656843000a2e 646f727020676e69 ...Checking prod
ffffffffc05927cc: 6f20444920746375 0a2e706968632066 uct ID of chip..
ffffffffc05927dc: 5120646e756f4600 204130303232414c .Found QLA2200A
ffffffffc05927ec: 43000a2e70696843 20676e696b636568 Chip...Checking
ffffffffc05927fc: 65786f626c69616d 6c636e69000a2e73 mailboxes...incl
ffffffffc059280c: 756e696c2f656475 616d2d616d642f78 ude/linux/dma-ma
crash> struct -ox srb_iocb
struct srb_iocb {
union {
struct {...} logio;
struct {...} els_logo;
struct {...} tmf;
struct {...} fxiocb;
struct {...} abt;
struct ct_arg ctarg;
struct {...} mbx;
struct {...} nack;
[0x0 ] } u;
[0xb8] struct timer_list timer;
[0x108] void (*timeout)(void *);
}
SIZE: 0x110
crash> ! bc
ibase=16
obase=10
B8+40
F8
The object is a srb_t, and at offset 0xf8 within that structure
(i.e. ffff95e5ff621080 + f8 -> ffff95e5ff621178) is a struct timer_list.
Cc: <stable@vger.kernel.org> #4.4+
Fixes: 4440e46d5db7 ("[SCSI] qla2xxx: Add IOCB Abort command asynchronous handling.")
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 28e9091e3119933c38933cb8fc48d5618eb784c8 upstream.
The user can provide very large cqe_size which will cause to integer
overflow as it can be seen in the following UBSAN warning:
=======================================================================
UBSAN: Undefined behaviour in drivers/infiniband/hw/mlx5/cq.c:1192:53
signed integer overflow:
64870 * 65536 cannot be represented in type 'int'
CPU: 0 PID: 267 Comm: syzkaller605279 Not tainted 4.15.0+ #90 Hardware
name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org 04/01/2014
Call Trace:
dump_stack+0xde/0x164
? dma_virt_map_sg+0x22c/0x22c
ubsan_epilogue+0xe/0x81
handle_overflow+0x1f3/0x251
? __ubsan_handle_negate_overflow+0x19b/0x19b
? lock_acquire+0x440/0x440
mlx5_ib_resize_cq+0x17e7/0x1e40
? cyc2ns_read_end+0x10/0x10
? native_read_msr_safe+0x6c/0x9b
? cyc2ns_read_end+0x10/0x10
? mlx5_ib_modify_cq+0x220/0x220
? sched_clock_cpu+0x18/0x200
? lookup_get_idr_uobject+0x200/0x200
? rdma_lookup_get_uobject+0x145/0x2f0
ib_uverbs_resize_cq+0x207/0x3e0
? ib_uverbs_ex_create_cq+0x250/0x250
ib_uverbs_write+0x7f9/0xef0
? cyc2ns_read_end+0x10/0x10
? print_irqtrace_events+0x280/0x280
? ib_uverbs_ex_create_cq+0x250/0x250
? uverbs_devnode+0x110/0x110
? sched_clock_cpu+0x18/0x200
? do_raw_spin_trylock+0x100/0x100
? __lru_cache_add+0x16e/0x290
__vfs_write+0x10d/0x700
? uverbs_devnode+0x110/0x110
? kernel_read+0x170/0x170
? sched_clock_cpu+0x18/0x200
? security_file_permission+0x93/0x260
vfs_write+0x1b0/0x550
SyS_write+0xc7/0x1a0
? SyS_read+0x1a0/0x1a0
? trace_hardirqs_on_thunk+0x1a/0x1c
entry_SYSCALL_64_fastpath+0x1e/0x8b
RIP: 0033:0x433549
RSP: 002b:00007ffe63bd1ea8 EFLAGS: 00000217
=======================================================================
Cc: syzkaller <syzkaller@googlegroups.com>
Cc: <stable@vger.kernel.org> # 3.13
Fixes: bde51583f49b ("IB/mlx5: Add support for resize CQ")
Reported-by: Noa Osherovich <noaos@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a5880b84430316e3e1c1f5d23aa32ec6000cc717 upstream.
The QP state is limited and declared in enum ib_qp_state,
but ucma user was able to supply any possible (u32) value.
Reported-by: syzbot+0df1ab766f8924b1edba@syzkaller.appspotmail.com
Fixes: 75216638572f ("RDMA/cma: Export rdma cm interface to userspace")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6a21dfc0d0db7b7e0acedce67ca533a6eb19283c upstream.
Users of ucma are supposed to provide size of option level,
in most paths it is supposed to be equal to u8 or u16, but
it is not the case for the IB path record, where it can be
multiple of struct ib_path_rec_data.
This patch takes simplest possible approach and prevents providing
values more than possible to allocate.
Reported-by: syzbot+a38b0e9f694c379ca7ce@syzkaller.appspotmail.com
Fixes: 7ce86409adcd ("RDMA/ucma: Allow user space to set service type")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit feb7695fe9fb83084aa29de0094774f4c9d4c9fc upstream.
If only a subset of the devices associated with multiple regions support
a given special operation (eg. DISCARD) then the dec_count() that is
used to set error for the region must increment the io->count.
Otherwise, when the dec_count() is called it can cause the dm-io
caller's bio to be completed multiple times. As was reported against
the dm-mirror target that had mirror legs with a mix of discard
capabilities.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=196077
Reported-by: Zhang Yi <yizhan@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d22ffb5a712f9211ffd104c38fc17cbfb1b5e2b0 ]
If multiple IPA commands are build & sent out concurrently,
fill_ipacmd_header() may assign a seqno value to a command that's
different from what send_control_data() later assigns to this command's
reply.
This is due to other commands passing through send_control_data(),
and incrementing card->seqno.ipa along the way.
So one IPA command has no reply that's waiting for its seqno, while some
other IPA command has multiple reply objects waiting for it.
Only one of those waiting replies wins, and the other(s) times out and
triggers a recovery via send_ipa_cmd().
Fix this by making sure that the same seqno value is assigned to
a command and its reply object.
Do so immediately before submitting the command & while holding the
irq_pending "lock", to produce nicely ascending seqnos.
As a side effect, *all* IPA commands now use a reply object that's
waiting for its actual seqno. Previously, early IPA commands that were
submitted while the card was still DOWN used the "catch-all" IDX seqno.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1c5b2216fbb973a9410e0b06389740b5c1289171 ]
send_control_data() applies some special handling to SETIP v4 IPA
commands. But current code parses *all* command types for the SETIP
command code. Limit the command code check to IPA commands.
Fixes: 5b54e16f1a54 ("qeth: do not spin for SETIP ip assist command")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 77f840e3e5f09c6d7d727e85e6e08276dd813d11 ]
PPP units don't hold any reference on the channels connected to it.
It is the channel's responsibility to ensure that it disconnects from
its unit before being destroyed.
In practice, this is ensured by ppp_unregister_channel() disconnecting
the channel from the unit before dropping a reference on the channel.
However, it is possible for an unregistered channel to connect to a PPP
unit: register a channel with ppp_register_net_channel(), attach a
/dev/ppp file to it with ioctl(PPPIOCATTCHAN), unregister the channel
with ppp_unregister_channel() and finally connect the /dev/ppp file to
a PPP unit with ioctl(PPPIOCCONNECT).
Once in this situation, the channel is only held by the /dev/ppp file,
which can be released at anytime and free the channel without letting
the parent PPP unit know. Then the ppp structure ends up with dangling
pointers in its ->channels list.
Prevent this scenario by forbidding unregistered channels from
connecting to PPP units. This maintains the code logic by keeping
ppp_unregister_channel() responsible from disconnecting the channel if
necessary and avoids modification on the reference counting mechanism.
This issue seems to predate git history (successfully reproduced on
Linux 2.6.26 and earlier PPP commits are unrelated).
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b6c3bad1ba83af1062a7ff6986d9edc4f3d7fc8e ]
Sometimes when physical lines have a just good noise to make the protocol
handshaking fail, but the carrier detect still good. Then after remove of
the noise, nobody will trigger this protocol to be start again to cause
the link to never come back. The fix is when the carrier is still on, not
terminate the protocol handshaking.
Signed-off-by: Denis Du <dudenis2000@yahoo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 20ac8f72514b3af8b62c520d55656ded865eff00, which
was commit 2b83ff96f51d0b039c4561b9f95c824d7bddb85c upstream.
The bug that it should fix was only introduced in Linux 4.7, and
in 4.4 it causes a regression.
Reported-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Cc: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3b9b95363c45365d606ad4bbba16acca75fdf6d3 upstream.
Per the documentation, use scnprintf instead of sprintf to ensure there
is never more than PAGE_SIZE bytes of trigger names put into the
buffer.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b9c97c67fd19262c002d94ced2bfb513083e161e upstream.
If m88d3103 chip ID is not recognized, the device is not initialized.
However, it returns from probe without any error, causing this OOPS:
[ 7.689289] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 7.689297] pgd = 7b0bd7a7
[ 7.689302] [00000000] *pgd=00000000
[ 7.689318] Internal error: Oops: 80000005 [#1] SMP ARM
[ 7.689322] Modules linked in: dvb_usb_dvbsky(+) m88ds3103 dvb_usb_v2 dvb_core videobuf2_vmalloc videobuf2_memops videobuf2_core crc32_arm_ce videodev media
[ 7.689358] CPU: 3 PID: 197 Comm: systemd-udevd Not tainted 4.15.0-mcc+ #23
[ 7.689361] Hardware name: BCM2835
[ 7.689367] PC is at 0x0
[ 7.689382] LR is at m88ds3103_attach+0x194/0x1d0 [m88ds3103]
[ 7.689386] pc : [<00000000>] lr : [<bf0ae1ec>] psr: 60000013
[ 7.689391] sp : ed8e5c20 ip : ed8c1e00 fp : ed8945c0
[ 7.689395] r10: ed894000 r9 : ed894378 r8 : eda736c0
[ 7.689400] r7 : ed894070 r6 : ed8e5c44 r5 : bf0bb040 r4 : eda77600
[ 7.689405] r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : eda77600
[ 7.689412] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 7.689417] Control: 10c5383d Table: 2d8e806a DAC: 00000051
[ 7.689423] Process systemd-udevd (pid: 197, stack limit = 0xe9dbfb63)
[ 7.689428] Stack: (0xed8e5c20 to 0xed8e6000)
[ 7.689439] 5c20: ed853a80 eda73640 ed894000 ed8942c0 ed853a80 bf0b9e98 ed894070 bf0b9f10
[ 7.689449] 5c40: 00000000 00000000 bf08c17c c08dfc50 00000000 00000000 00000000 00000000
[ 7.689459] 5c60: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.689468] 5c80: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.689479] 5ca0: 00000000 00000000 ed8945c0 ed8942c0 ed894000 ed894830 bf0b9e98 00000000
[ 7.689490] 5cc0: ed894378 bf0a3cb4 bf0bc3b0 0000533b ed920540 00000000 00000034 bf0a6434
[ 7.689500] 5ce0: ee952070 ed826600 bf0a7038 bf0a2dd8 00000001 bf0a6768 bf0a2f90 ed8943c0
[ 7.689511] 5d00: 00000000 c08eca68 ed826620 ed826620 00000000 ee952070 bf0bc034 ee952000
[ 7.689521] 5d20: ed826600 bf0bb080 ffffffed c0aa9e9c c0aa9dac ed826620 c16edf6c c168c2c8
[ 7.689531] 5d40: c16edf70 00000000 bf0bc034 0000000d 00000000 c08e268c bf0bb080 ed826600
[ 7.689541] 5d60: bf0bc034 ed826654 ed826620 bf0bc034 c164c8bc 00000000 00000001 00000000
[ 7.689553] 5d80: 00000028 c08e2948 00000000 bf0bc034 c08e2848 c08e0778 ee9f0a58 ed88bab4
[ 7.689563] 5da0: bf0bc034 ed90ba80 c168c1f0 c08e1934 bf0bb3bc c17045ac bf0bc034 c164c8bc
[ 7.689574] 5dc0: bf0bc034 bf0bb3bc ed91f564 c08e34ec bf0bc000 c164c8bc bf0bc034 c0aa8dc4
[ 7.689584] 5de0: ffffe000 00000000 bf0bf000 ed91f600 ed91f564 c03021e4 00000001 00000000
[ 7.689595] 5e00: c166e040 8040003f ed853a80 bf0bc448 00000000 c1678174 ed853a80 f0f22000
[ 7.689605] 5e20: f0f21fff 8040003f 014000c0 ed91e700 ed91e700 c16d8e68 00000001 ed91e6c0
[ 7.689615] 5e40: bf0bc400 00000001 bf0bc400 ed91f564 00000001 00000000 00000028 c03c9a24
[ 7.689625] 5e60: 00000001 c03c8c94 ed8e5f50 ed8e5f50 00000001 bf0bc400 ed91f540 c03c8cb0
[ 7.689637] 5e80: bf0bc40c 00007fff bf0bc400 c03c60b0 00000000 bf0bc448 00000028 c0e09684
[ 7.689647] 5ea0: 00000002 bf0bc530 c1234bf8 bf0bc5dc bf0bc514 c10ebbe8 ffffe000 bf000000
[ 7.689657] 5ec0: 00011538 00000000 ed8e5f48 00000000 00000000 00000000 00000000 00000000
[ 7.689666] 5ee0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 7.689676] 5f00: 00000000 00000000 7fffffff 00000000 00000013 b6e55a18 0000017b c0309104
[ 7.689686] 5f20: ed8e4000 00000000 00510af0 c03c9430 7fffffff 00000000 00000003 00000000
[ 7.689697] 5f40: 00000000 f0f0f000 00011538 00000000 f0f107b0 f0f0f000 00011538 f0f1fdb8
[ 7.689707] 5f60: f0f1fbe8 f0f1b974 00004000 000041e0 bf0bc3d0 00000001 00000000 000024c4
[ 7.689717] 5f80: 0000002d 0000002e 00000019 00000000 00000010 00000000 16894000 00000000
[ 7.689727] 5fa0: 00000000 c0308f20 16894000 00000000 00000013 b6e55a18 00000000 b6e5652c
[ 7.689737] 5fc0: 16894000 00000000 00000000 0000017b 00020000 00508110 00000000 00510af0
[ 7.689748] 5fe0: bef68948 bef68938 b6e4d3d0 b6d32590 60000010 00000013 00000000 00000000
[ 7.689790] [<bf0ae1ec>] (m88ds3103_attach [m88ds3103]) from [<bf0b9f10>] (dvbsky_s960c_attach+0x78/0x280 [dvb_usb_dvbsky])
[ 7.689821] [<bf0b9f10>] (dvbsky_s960c_attach [dvb_usb_dvbsky]) from [<bf0a3cb4>] (dvb_usbv2_probe+0xa3c/0x1024 [dvb_usb_v2])
[ 7.689849] [<bf0a3cb4>] (dvb_usbv2_probe [dvb_usb_v2]) from [<c0aa9e9c>] (usb_probe_interface+0xf0/0x2a8)
[ 7.689869] [<c0aa9e9c>] (usb_probe_interface) from [<c08e268c>] (driver_probe_device+0x2f8/0x4b4)
[ 7.689881] [<c08e268c>] (driver_probe_device) from [<c08e2948>] (__driver_attach+0x100/0x11c)
[ 7.689895] [<c08e2948>] (__driver_attach) from [<c08e0778>] (bus_for_each_dev+0x4c/0x9c)
[ 7.689909] [<c08e0778>] (bus_for_each_dev) from [<c08e1934>] (bus_add_driver+0x1c0/0x264)
[ 7.689919] [<c08e1934>] (bus_add_driver) from [<c08e34ec>] (driver_register+0x78/0xf4)
[ 7.689931] [<c08e34ec>] (driver_register) from [<c0aa8dc4>] (usb_register_driver+0x70/0x134)
[ 7.689946] [<c0aa8dc4>] (usb_register_driver) from [<c03021e4>] (do_one_initcall+0x44/0x168)
[ 7.689963] [<c03021e4>] (do_one_initcall) from [<c03c9a24>] (do_init_module+0x64/0x1f4)
[ 7.689979] [<c03c9a24>] (do_init_module) from [<c03c8cb0>] (load_module+0x20a0/0x25c8)
[ 7.689993] [<c03c8cb0>] (load_module) from [<c03c9430>] (SyS_finit_module+0xb4/0xec)
[ 7.690007] [<c03c9430>] (SyS_finit_module) from [<c0308f20>] (ret_fast_syscall+0x0/0x54)
[ 7.690018] Code: bad PC value
This may happen on normal circumstances, if, for some reason, the demod
hangs and start returning an invalid chip ID:
[ 10.394395] m88ds3103 3-0068: Unknown device. Chip_id=00
So, change the logic to cause probe to fail with -ENODEV, preventing
the OOPS.
Detected while testing DVB MMAP patches on Raspberry Pi 3 with
DVBSky S960CI.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0373ca74831b0f93cd4cdbf7ad3aec3c33a479a5 upstream.
commit a307a1e6bc0d "cpufreq: s3c: use cpufreq_generic_init()"
accidentally broke cpufreq on s3c2410 and s3c2412.
These two platforms don't have a CPU frequency table and used to skip
calling cpufreq_table_validate_and_show() for them. But with the
above commit, we started calling it unconditionally and that will
eventually fail as the frequency table pointer is NULL.
Fix this by calling cpufreq_table_validate_and_show() conditionally
again.
Fixes: a307a1e6bc0d "cpufreq: s3c: use cpufreq_generic_init()"
Cc: 3.13+ <stable@vger.kernel.org> # v3.13+
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f9d4d9b5a5ef2f017bc344fb65a58a902517173b upstream.
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
the bus
commit 9b8cb28d7c62568a5916bdd7ea1c9176d7f8f2ed upstream.
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6d24cd186d9fead3722108dec1b1c993354645ff upstream.
Discrete TPMs are often connected over slow serial buses which, on
some platforms, can have glitches causing bit flips. In all the
driver _recv() functions, we need to use a u32 to unmarshal the
response size, otherwise a bit flip of the 31st bit would cause the
expected variable to go negative, which would then try to read a huge
amount of data. Also sanity check that the expected amount of data is
large enough for the TPM header.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 11d827a993a969c3c6ec56758ff63a44ba19b466 ]
set_fipers() calling should be protected by spinlock in
case that any interrupt breaks related registers setting
and the function we expect. This patch is to move set_fipers()
to spinlock protecting area in ptp_gianfar_adjtime().
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cf2acf66ad43abb39735568f55e1f85f9844e990 ]
When cleaning up after a partially successful gntdev_mmap(), unmap the
successfully mapped grant pages otherwise Xen will kill the domain if
in debug mode (Attempt to implicitly unmap a granted PTE) or Linux will
kill the process and emit "BUG: Bad page map in process" if Xen is in
release mode.
This is only needed when use_ptemod is true because gntdev_put_map()
will unmap grant pages itself when use_ptemod is false.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 951a010233625b77cde3430b4b8785a9a22968d1 ]
If the requested range has a hole, the calculation of the number of
pages to unmap is off by one. Fix it.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 56c0290202ab94a2f2780c449395d4ae8495fab4 ]
If the probing of the regulator is deferred, the memory allocated by
'mdiobus_alloc_size()' will be leaking.
It should be freed before the next call to 'sun4i_mdio_probe()' which will
reallocate it.
Fixes: 4bdcb1dd9feb ("net: Add MDIO bus driver for the Allwinner EMAC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b707fda2df4070785d0fa8a278aa13944c5f51f8 ]
When loading the module after unloading it, the network interface would
not be enabled and thus wouldn't have a backend counterpart and unable
to be used by the guest.
The guest would face errors like:
[root@guest ~]# ethtool -i eth0
Cannot get driver information: No such device
[root@guest ~]# ifconfig eth0
eth0: error fetching interface information: Device not found
This patch initializes the state of the netfront device whenever it is
loaded manually, this state would communicate the netback to create its
device and establish the connection between them.
Signed-off-by: Eduardo Otubo <otubo@redhat.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 78f300049335ae81a5cc6b4b232481dc5e1f9d41 ]
In bnxt_vf_ndo_prep (which is called by bnxt_get_vf_config ndo), there is a
check for "Invalid VF id". Currently, the check is done against max_vfs.
However, the user doesn't always create max_vfs. So, the check should be
against the created number of VFs. The number of bnxt_vf_info structures
that are allocated in bnxt_alloc_vf_resources routine is the "number of
requested VFs". So, if an "invalid VF id" falls between the requested
number of VFs and the max_vfs, the driver will be dereferencing an invalid
pointer.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Devvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 13454c14550065fcc1705d6bd4ee6d40e057099f ]
The flexcan_start_xmit() function compares the frame length with data
register length to write frame content into data[0] and data[1]
register. Data register length is 4 bytes and frame maximum length is 8
bytes.
Fix the check that compares frame length with 3. Because the register
length is 4.
Signed-off-by: Luu An Phu <phu.luuan@nxp.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 19d859a7205bc59ffc38303eb25ae394f61d21dc ]
In the function ttm_page_alloc_init, kzalloc call is made for variable
_manager, we need to check its return value, it may return NULL.
Signed-off-by: Xiongwei Song <sxwjean@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 0b76aae741abb9d16d2c0e67f8b1e766576f897d ]
This patch adds check so that driver does not disable already
disabled device.
[ 44.637743] advantechwdt: Unexpected close, not stopping watchdog!
[ 44.997548] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input6
[ 45.013419] e1000 0000:00:03.0: disabling already-disabled device
[ 45.013447] ------------[ cut here ]------------
[ 45.014868] WARNING: CPU: 1 PID: 71 at drivers/pci/pci.c:1641 pci_disable_device+0xa1/0x105:
pci_disable_device at drivers/pci/pci.c:1640
[ 45.016171] CPU: 1 PID: 71 Comm: rcu_perf_shutdo Not tainted 4.14.0-01330-g3c07399 #1
[ 45.017197] task: ffff88011bee9e40 task.stack: ffffc90000860000
[ 45.017987] RIP: 0010:pci_disable_device+0xa1/0x105:
pci_disable_device at drivers/pci/pci.c:1640
[ 45.018603] RSP: 0000:ffffc90000863e30 EFLAGS: 00010286
[ 45.019282] RAX: 0000000000000035 RBX: ffff88013a230008 RCX: 0000000000000000
[ 45.020182] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000203
[ 45.021084] RBP: ffff88013a3f31e8 R08: 0000000000000001 R09: 0000000000000000
[ 45.021986] R10: ffffffff827ec29c R11: 0000000000000002 R12: 0000000000000001
[ 45.022946] R13: ffff88013a230008 R14: ffff880117802b20 R15: ffffc90000863e8f
[ 45.023842] FS: 0000000000000000(0000) GS:ffff88013fd00000(0000) knlGS:0000000000000000
[ 45.024863] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 45.025583] CR2: ffffc900006d4000 CR3: 000000000220f000 CR4: 00000000000006a0
[ 45.026478] Call Trace:
[ 45.026811] __e1000_shutdown+0x1d4/0x1e2:
__e1000_shutdown at drivers/net/ethernet/intel/e1000/e1000_main.c:5162
[ 45.027344] ? rcu_perf_cleanup+0x2a1/0x2a1:
rcu_perf_shutdown at kernel/rcu/rcuperf.c:627
[ 45.027883] e1000_shutdown+0x14/0x3a:
e1000_shutdown at drivers/net/ethernet/intel/e1000/e1000_main.c:5235
[ 45.028351] device_shutdown+0x110/0x1aa:
device_shutdown at drivers/base/core.c:2807
[ 45.028858] kernel_power_off+0x31/0x64:
kernel_power_off at kernel/reboot.c:260
[ 45.029343] rcu_perf_shutdown+0x9b/0xa7:
rcu_perf_shutdown at kernel/rcu/rcuperf.c:637
[ 45.029852] ? __wake_up_common_lock+0xa2/0xa2:
autoremove_wake_function at kernel/sched/wait.c:376
[ 45.030414] kthread+0x126/0x12e:
kthread at kernel/kthread.c:233
[ 45.030834] ? __kthread_bind_mask+0x8e/0x8e:
kthread at kernel/kthread.c:190
[ 45.031399] ? ret_from_fork+0x1f/0x30:
ret_from_fork at arch/x86/entry/entry_64.S:443
[ 45.031883] ? kernel_init+0xa/0xf5:
kernel_init at init/main.c:997
[ 45.032325] ret_from_fork+0x1f/0x30:
ret_from_fork at arch/x86/entry/entry_64.S:443
[ 45.032777] Code: 00 48 85 ed 75 07 48 8b ab a8 00 00 00 48 8d bb 98 00 00 00 e8 aa d1 11 00 48 89 ea 48 89 c6 48 c7 c7 d8 e4 0b 82 e8 55 7d da ff <0f> ff b9 01 00 00 00 31 d2 be 01 00 00 00 48 c7 c7 f0 b1 61 82
[ 45.035222] ---[ end trace c257137b1b1976ef ]---
[ 45.037838] ACPI: Preparing to enter system sleep state S5
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 16ba3defb8bd01a9464ba4820a487f5b196b455b ]
When using enhanced mode for IPoIB, two threads may execute xmit in
parallel to two different TX queues while the target is the same.
In this case, both of them will add the same neighbor to the path's
neigh link list and we might see the following message:
list_add double add: new=ffff88024767a348, prev=ffff88024767a348...
WARNING: lib/list_debug.c:31__list_add_valid+0x4e/0x70
ipoib_start_xmit+0x477/0x680 [ib_ipoib]
dev_hard_start_xmit+0xb9/0x3e0
sch_direct_xmit+0xf9/0x250
__qdisc_run+0x176/0x5d0
__dev_queue_xmit+0x1f5/0xb10
__dev_queue_xmit+0x55/0xb10
Analysis:
Two SKB are scheduled to be transmitted from two cores.
In ipoib_start_xmit, both gets NULL when calling ipoib_neigh_get.
Two calls to neigh_add_path are made. One thread takes the spin-lock
and calls ipoib_neigh_alloc which creates the neigh structure,
then (after the __path_find) the neigh is added to the path's neigh
link list. When the second thread enters the critical section it also
calls ipoib_neigh_alloc but in this case it gets the already allocated
ipoib_neigh structure, which is already linked to the path's neigh
link list and adds it again to the list. Which beside of triggering
the list, it creates a loop in the linked list. This loop leads to
endless loop inside path_rec_completion.
Solution:
Check list_empty(&neigh->list) before adding to the list.
Add a similar fix in "ipoib_multicast.c::ipoib_mcast_send"
Fixes: b63b70d87741 ('IPoIB: Use a private hash table for path lookup in xmit path')
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5a371cf87e145b86efd32007e46146e78c1eff6d ]
ibmr.device is being set only after ib_alloc_mr() is successfully complete.
Therefore, in case imlx4_mr_enable() returns with error, the error flow
unwinder calls to mlx4_free_priv_pages(), which uses ibmr.device.
Such usage causes to NULL dereference oops and to fix it, the IB device
should be set in the mr struct earlier stage (e.g. prior to calling
mlx4_free_priv_pages()).
Fixes: 1b2cd0fc673c ("IB/mlx4: Support the new memory registration API")
Signed-off-by: Nitzan Carmi <nitzanc@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8a9bd4f8ebc6800bfc0596e28631ff6809a2f615 ]
We store per path and per device configuration data to identify the
path or device correctly. The per path configuration data might get
mixed up if the original request gets into error recovery and is
started with a random path mask.
This would lead to a wrong identification of a path in case of a CUIR
event for example.
Fix by copying the path mask from the original request to the error
recovery request in case it is a path verification request.
Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2b83ff96f51d0b039c4561b9f95c824d7bddb85c ]
With the current code, the following sequence won't work :
echo timer > trigger
echo 0 > delay_off
* at this point we call
** led_delay_off_store
** led_blink_set
|
|
[ Upstream commit f7084059a9cb9e56a186e1677b1dcffd76c2cd24 ]
While in recovery process of PCI error (called EEH on PowerPC arch),
another PCI transaction could be corrupted causing a situation of
nested PCI errors. Also, this scenario could be reproduced with
error injection mechanisms (for debug purposes).
We observe that in case of nested PCI errors, bnx2x might attempt to
initialize its shmem and cause a kernel crash due to bad addresses
read from MCP. Multiple different stack traces were observed depending
on the point the second PCI error happens.
This patch avoids the crashes by:
* failing PCI recovery in case of nested errors (since multiple
PCI errors in a row are not expected to lead to a functional
adapter anyway), and by,
* preventing access to adapter FW when MCP is failed (we mark it as
failed when shmem cannot get initialized properly).
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Shahed Shaikh <Shahed.Shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e60ee41aaf898584205a6af5c996860d0fe6a836 ]
A customer noticed RX path hang when MTU is changed on the fly while
running heavy traffic with NCSI enabled for 5717 and 5719. Since 5720
belongs to same ASIC family, we observed same issue and same fix
could solve this problem for 5720.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|