summaryrefslogtreecommitdiff
path: root/include
AgeCommit message (Collapse)Author
2009-09-04sctp: turn flags in 'struct sctp_association' into bit fieldsWei Yongjun
This shrinks the size of struct sctp_association a little. Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04sctp: Sysctl configuration for IPv4 Address ScopingBhaskar Dutta
This patch introduces a new sysctl option to make IPv4 Address Scoping configurable <draft-stewart-tsvwg-sctp-ipv4-00.txt>. In networking environments where DNAT rules in iptables prerouting chains convert destination IP's to link-local/private IP addresses, SCTP connections fail to establish as the INIT chunk is dropped by the kernel due to address scope match failure. For example to support overlapping IP addresses (same IP address with different vlan id) a Layer-5 application listens on link local IP's, and there is a DNAT rule that maps the destination IP to a link local IP. Such applications never get the SCTP INIT if the address-scoping draft is strictly followed. This sysctl configuration allows SCTP to function in such unconventional networking environments. Sysctl options: 0 - Disable IPv4 address scoping draft altogether 1 - Enable IPv4 address scoping (default, current behavior) 2 - Enable address scoping but allow IPv4 private addresses in init/init-ack 3 - Enable address scoping but allow IPv4 link local address in init/init-ack Signed-off-by: Bhaskar Dutta <bhaskar.dutta@globallogic.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04sctp: Turn flags in 'sctp_packet' into bit fieldsVlad Yasevich
This shrinks the size of sctp_packet a little. Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04sctp: Fix SCTP_MAXSEG socket option to comply to spec.Vlad Yasevich
We had a bug that we never stored the user-defined value for MAXSEG when setting the value on an association. Thus future PMTU events ended up re-writing the frag point and increasing it past user limit. Additionally, when setting the option on the socket/endpoint, we effect all current associations, which is against spec. Now, we store the user 'maxseg' value along with the computed 'frag_point'. We inherit 'maxseg' from the socket at association creation and use it as an upper limit for 'frag_point' when its set. Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04sctp: Don't do NAGLE delay on large writes that were fragmented smallVlad Yasevich
SCTP will delay the last part of a large write due to NAGLE, if that part is smaller then MTU. Since we are doing large writes, we might as well send the last portion now instead of waiting untill the next large write happens. The small portion will be sent as is regardless, so it's better to not delay it. This is a result of much discussions with Wei Yongjun <yjwei@cn.fujitsu.com> and Doug Graham <dgraham@nortel.com>. Many thanks go out to them. Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04sctp: drop a_rwnd to 0 when receive buffer overflows.Vlad Yasevich
SCTP has a problem that when small chunks are used, it is possible to exhaust the receiver buffer without fully closing receive window. This happens due to all overhead that we have account for with small messages. To fix this, when receive buffer is exceeded, we'll drop the window to 0 and save the 'drop' portion. When application starts reading data and freeing up recevie buffer space, we'll wait until we've reached the 'drop' window and then add back this 'drop' one mtu at a time. This worked well in testing and under stress produced rather even recovery. Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04sctp: Send user messages to the lower layer as oneVlad Yasevich
Currenlty, sctp breaks up user messages into fragments and sends each fragment to the lower layer by itself. This means that for each fragment we go all the way down the stack and back up. This also discourages bundling of multiple fragments when they can fit into a sigle packet (ex: due to user setting a low fragmentation threashold). We introduce a new command SCTP_CMD_SND_MSG and hand the whole message down state machine. The state machine and the side-effect parser will cork the queue, add all chunks from the message to the queue, and then un-cork the queue thus causing the chunks to get transmitted. Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04sctp: Disallow new connection on a closing socketVlad Yasevich
If a socket has a lot of association that are in the process of of being closed/aborted, it is possible for a remote to establish new associations during the time period that the old ones are shutting down. If this was a result of a close() call, there will be no socket and will cause a memory leak. We'll prevent this by setting the socket state to CLOSING and disallow new associations when in this state. Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04sctp: remove unused union (sctp_cmsg_data_t) definitionRami Rosen
This patch removes an unused union definition (sctp_cmsg_data_t) from include/net/sctp/user.h. Signed-off-by: Rami Rosen <rosenrami@gmail.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-09-04can: add can_free_echo_skb() for upcoming driversWolfgang Grandegger
This patch adds the function can_free_echo_skb to the CAN device interface to allow upcoming drivers to release echo skb's in case of error. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02tcp: replace hard coded GFP_KERNEL with sk_allocationWu Fengguang
This fixed a lockdep warning which appeared when doing stress memory tests over NFS: inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-W} usage. page reclaim => nfs_writepage => tcp_sendmsg => lock sk_lock mount_root => nfs_root_data => tcp_close => lock sk_lock => tcp_send_fin => alloc_skb_fclone => page reclaim David raised a concern that if the allocation fails in tcp_send_fin(), and it's GFP_ATOMIC, we are going to yield() (which sleeps) and loop endlessly waiting for the allocation to succeed. But fact is, the original GFP_KERNEL also sleeps. GFP_ATOMIC+yield() looks weird, but it is no worse the implicit sleep inside GFP_KERNEL. Both could loop endlessly under memory pressure. CC: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> CC: David S. Miller <davem@davemloft.net> CC: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02net/ethtool: Add support for the ethtool feature to flash firmware image ↵Ajit Khaparde
from a specified file. This patch adds support to flash a firmware image to a device using ethtool. The driver gets the filename of the firmware image and flashes the image using the request firmware path. The region "on the chip" to be flashed can be specified by an option. It is upto the device driver to enumerate the region number passed by ethtool, to the region to be flashed. The default behavior is to flash all the regions on the chip. Signed-off-by: Ajit Khaparde <ajitk@serverengines.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02vlan: multiqueue vlan deviceEric Dumazet
vlan devices are currently not multi-queue capable. We can do that with a new rtnl_link_ops method, get_tx_queues(), called from rtnl_create_link() This new method gets num_tx_queues/real_num_tx_queues from real device. register_vlan_device() is also handled. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
2009-09-02inet: inet_connection_sock_af_ops constStephen Hemminger
The function block inet_connect_sock_af_ops contains no data make it constant. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02tcp: MD5 operations should be constStephen Hemminger
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-02Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/yellowfin.c
2009-09-01pkt_sched: Revert tasklet_hrtimer changes.David S. Miller
These are full of unresolved problems, mainly that conversions don't work 1-1 from hrtimers to tasklet_hrtimers because unlike hrtimers tasklets can't be killed from softirq context. And when a qdisc gets reset, that's exactly what we need to do here. We'll work this out in the net-next-2.6 tree and if warranted we'll backport that work to -stable. This reverts the following 3 changesets: a2cb6a4dd470d7a64255a10b843b0d188416b78f ("pkt_sched: Fix bogon in tasklet_hrtimer changes.") 38acce2d7983632100a9ff3fd20295f6e34074a8 ("pkt_sched: Convert CBQ to tasklet_hrtimer.") ee5f9757ea17759e1ce5503bdae2b07e48e32af9 ("pkt_sched: Convert qdisc_watchdog to tasklet_hrtimer") Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01net: make neigh_ops constantStephen Hemminger
These tables are never modified at runtime. Move to read-only section. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01RTO connection timeout: coding style fixes and commentsDamian Lukowski
This patch affects the retransmits_timed_out() function. Changes: 1) Variables have more meaningful names 2) retransmits_timed_out() has an introductionary comment. 3) Small coding style changes. Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01netns: embed ip6_dst_ops directlyAlexey Dobriyan
struct net::ipv6.ip6_dst_ops is separatedly dynamically allocated, but there is no fundamental reason for it. Embed it directly into struct netns_ipv6. For that: * move struct dst_ops into separate header to fix circular dependencies I honestly tried not to, it's pretty impossible to do other way * drop dynamical allocation, allocate together with netns For a change, remove struct dst_ops::dst_net, it's deducible by using container_of() given dst_ops pointer. Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01rfkill: relicense header fileJohannes Berg
This header file is copied into userspace tools that need not be GPLv2 licensed, make that easier. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk> Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Acked-by: Iñaky Pérez-González <inaky@linux.intel.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com> Acked-by: Michael Buesch <mb@bu3sch.de> Acked-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-09-01Revert Backoff [v3]: Calculate TCP's connection close threshold as a time value.Damian Lukowski
RFC 1122 specifies two threshold values R1 and R2 for connection timeouts, which may represent a number of allowed retransmissions or a timeout value. Currently linux uses sysctl_tcp_retries{1,2} to specify the thresholds in number of allowed retransmissions. For any desired threshold R2 (by means of time) one can specify tcp_retries2 (by means of number of retransmissions) such that TCP will not time out earlier than R2. This is the case, because the RTO schedule follows a fixed pattern, namely exponential backoff. However, the RTO behaviour is not predictable any more if RTO backoffs can be reverted, as it is the case in the draft "Make TCP more Robust to Long Connectivity Disruptions" (http://tools.ietf.org/html/draft-zimmermann-tcp-lcd). In the worst case TCP would time out a connection after 3.2 seconds, if the initial RTO equaled MIN_RTO and each backoff has been reverted. This patch introduces a function retransmits_timed_out(N), which calculates the timeout of a TCP connection, assuming an initial RTO of MIN_RTO and N unsuccessful, exponentially backed-off retransmissions. Whenever timeout decisions are made by comparing the retransmission counter to some value N, this function can be used, instead. The meaning of tcp_retries2 will be changed, as many more RTO retransmissions can occur than the value indicates. However, it yields a timeout which is similar to the one of an unpatched, exponentially backing off TCP in the same scenario. As no application could rely on an RTO greater than MIN_RTO, there should be no risk of a regression. Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de> Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01Revert Backoff [v3]: Revert RTO on ICMP destination unreachableDamian Lukowski
Here, an ICMP host/network unreachable message, whose payload fits to TCP's SND.UNA, is taken as an indication that the RTO retransmission has not been lost due to congestion, but because of a route failure somewhere along the path. With true congestion, a router won't trigger such a message and the patched TCP will operate as standard TCP. This patch reverts one RTO backoff, if an ICMP host/network unreachable message, whose payload fits to TCP's SND.UNA, arrives. Based on the new RTO, the retransmission timer is reset to reflect the remaining time, or - if the revert clocked out the timer - a retransmission is sent out immediately. Backoffs are only reverted, if TCP is in RTO loss recovery, i.e. if there have been retransmissions and reversible backoffs, already. Changes from v2: 1) Renaming of skb in tcp_v4_err() moved to another patch. 2) Reintroduced tcp_bound_rto() and __tcp_set_rto(). 3) Fixed code comments. Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de> Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01dcbnl: Add support for setapp/getapp to netdev dcbnl_rtnl_opsYi Zou
Adds support of dcbnl setapp/getapp to dcbnl_rtnl_ops in netdev to allow LLDs to implement their corresponding dcbnl setapp/getapp ops to support the IEEE 802.1Q DCBX setapp/getapp commands. Signed-off-by: Yi Zou <yi.zou@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01dcbnl: Add support for setapp/getapp commands to dcbnlYi Zou
This patch adds dcbnl command definitions to support setapp/getapp functionality from the IEEE 802.1Qaz Data Center Bridging Capability Exchange protocol (DCBX) specification. Section 3.3 defines the application protocol and its 802.1p user priority in DCBX, which is implemented here as a pair of setapp/getapp commands in the kernel dcbnl for setting and retrieving the user priority for an given application protocol. The protocol is identified by the combination of an id and an idtype. Currently, when idtype is 0, the corresponding id gives the ether type of this protocol, e.g., for FCoE, it will be 0x8906; when idtype is 1, then the corresponding id gives the TCP or UDP port number. For more information regarding DCBX spec., please refer to the following: http://www.ieee802.org/1/files/public/docs2008/ az-wadekar-dcbx-capability-exchange-discovery-protocol-1108-v1.01.pdf Signed-off-by: Yi Zou <yi.zou@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01net: Add ndo_fcoe_enable/ndo_fcoe_disable to net_device_opsYi Zou
Add ndo_fcoe_enable/_disable to net_device_ops so the corresponding HW can initialize itself for FCoE traffic or clean up after FCoE traffic is done. This is expected to be called by the kernel FCoE stack upon receiving a request for creating an FCoE instance on the corresponding netdev interface. When implemented by the actual HW, the HW driver check the op code to perform corresponding initialization or clean up for FCoE. The initialization normally includes allocating extra queues for FCoE, setting corresponding HW registers for FCoE, indicating FCoE offload features via netdev, etc. The clean-up would include releasing the resources allocated for FCoE. Signed-off-by: Yi Zou <yi.zou@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01netdev: convert bulk of drivers to netdev_tx_tStephen Hemminger
In a couple of cases collapse some extra code like: int retval = NETDEV_TX_OK; ... return retval; into return NETDEV_TX_OK; Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01hdlc: convert to netdev_tx_tStephen Hemminger
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01usbnet: convert to netdev_tx_tStephen Hemminger
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-01netdev: change transmit to limited range typeStephen Hemminger
The transmit function should only return one of three possible values, some drivers got confused and returned errno's or other values. This changes the definition so that this can be caught at compile time. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-30netdevice: Consolidate to use existing macros where available.Krishna Kumar
Patch compiled and 32 simultaneous netperf testing ran fine. Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-30Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/holtmann/bluetooth-next-2.6
2009-08-29tg3: Add new 5785 10/100 only device IDMatt Carlson
This patch adds a new device ID for those 5785 devices that will only use 10/100 phys. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-28tcp: keepalive cleanupsEric Dumazet
Introduce keepalive_probes(tp) helper, and use it, like keepalive_time_when(tp) and keepalive_intvl_when(tp) Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-28ssb: Implement PMU LDO control and use it in b43Gábor Stefanik
Implement the "PMU LDO set voltage" and "PMU LDO PA ref enable" functions, and use them during LP-PHY baseband init in b43. Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28mac80211: remove ieee80211_rx namespace hackJohn W. Linville
With the libipw naming scheme change, it is no longer necessary for mac80211 to avoid the ieee80211_rx name clash. Reported-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28libipw: switch from ieee80211_* to libipw_* naming policyJohn W. Linville
This eliminates the dual definition of ieee80211_channel (and possibly others), further clarifying who defines what and paving the way for inclusion of cfg80211.h. Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-28mac80211: Update mesh config IE to 11s draft 3.02Javier Cardona
The mesh config information element has changed significantly since draft 1.08 This patch brings it up to date. Thanks to Sam Leffler and Rui Paulo for identifying this. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-08-26Bluetooth: Handle L2CAP case when the remote receiver is busyGustavo F. Padovan
Implement all issues related to RemoteBusy in the RECV state table. Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-23Merge branch 'for-next' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/lowpan/lowpan
2009-08-23RDS: Add TCP transport to RDSAndy Grover
This code allows RDS to be tunneled over a TCP connection. RDMA operations are disabled when using TCP transport, but this frees RDS from the IB/RDMA stack dependency, and allows it to be used with standard Ethernet adapters, or in a VM. Signed-off-by: Andy Grover <andy.grover@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-22pkt_sched: Convert qdisc_watchdog to tasklet_hrtimerDavid S. Miller
None of this stuff should execute in hw IRQ context, therefore use a tasklet_hrtimer so that it runs in softirq context. Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Thomas Gleixner <tglx@linutronix.de>
2009-08-22Bluetooth: Fix rejected connection not disconnecting ACL linkLuiz Augusto von Dentz
When using DEFER_SETUP on a RFCOMM socket, a SABM frame triggers authorization which when rejected send a DM response. This is fine according to the RFCOMM spec: the responding implementation may replace the "proper" response on the Multiplexer Control channel with a DM frame, sent on the referenced DLCI to indicate that the DLCI is not open, and that the responder would not grant a request to open it later either. But some stacks doesn't seems to cope with this leaving DLCI 0 open after receiving DM frame. To fix it properly a timer was introduced to rfcomm_session which is used to set a timeout when the last active DLC of a session is unlinked, this will give the remote stack some time to reply with a proper DISC frame on DLCI 0 avoiding both sides sending DISC to each other on stacks that follow the specification and taking care of those who don't by taking down DLCI 0. Signed-off-by: Luiz Augusto von Dentz <luiz.dentz@openbossa.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22Bluetooth: Full support for receiving L2CAP SREJ framesGustavo F. Padovan
Support for receiving of SREJ frames as specified by the state table. Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22Bluetooth: Add support for L2CAP SREJ exceptionGustavo F. Padovan
When L2CAP loses an I-frame we send a SREJ frame to the transmitter side requesting the lost packet. This patch implement all Recv I-frame events on SREJ_SENT state table except the ones that deal with SendRej (the REJ exception at receiver side is yet not implemented). Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22Bluetooth: Add support for FCS option to L2CAPGustavo F. Padovan
Implement CRC16 check for L2CAP packets. FCS is used by Streaming Mode and Enhanced Retransmission Mode and is a extra check for the packet content. Using CRC16 is the default, L2CAP won't use FCS only when both side send a "No FCS" request. Initially based on a patch from Nathan Holstein <nathan@lampreynetworks.com> Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22Bluetooth: Add support for Retransmission and Monitor TimersGustavo F. Padovan
L2CAP uses retransmission and monitor timers to inquiry the other side about unacked I-frames. After sending each I-frame we (re)start the retransmission timer. If it expires, we start a monitor timer that send a S-frame with P bit set and wait for S-frame with F bit set. If monitor timer expires, try again, at a maximum of L2CAP_DEFAULT_MAX_TX. Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22Bluetooth: Initial support for retransmission of packets with REJ framesGustavo F. Padovan
When receiving an I-frame with unexpected txSeq, receiver side start the recovery procedure by sending a REJ S-frame to the transmitter side. So the transmitter can re-send the lost I-frame. This patch just adds a basic support for retransmission, it doesn't mean that ERTM now has full support for packet retransmission. Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2009-08-22Bluetooth: Add support for Segmentation and Reassembly of SDUsGustavo F. Padovan
ERTM should use Segmentation and Reassembly to break down a SDU in many PDUs on sending data to the other side. On sending packets we queue all 'segments' until end of segmentation and just the add them to the queue for sending. On receiving we create a new SKB with the SDU reassembled. Initially based on a patch from Nathan Holstein <nathan@lampreynetworks.com> Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>