From 5ecd52e563f1e14f9cfe06130fbf9fdb73f227e8 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 20 Mar 2013 17:44:41 +0200 Subject: ARM: OMAP2+: omap-usb-host: Add usbhs_init_phys() This helper allows board support code to add the PHY's VCC and RESET regulators which are GPIO controlled as well as the NOP PHY device. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/usb-host.c | 160 ++++++++++++++++++++++++++++++++++++++++- arch/arm/mach-omap2/usb.h | 9 +++ 2 files changed, 167 insertions(+), 2 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/usb-host.c b/arch/arm/mach-omap2/usb-host.c index 5706bdccf45e..aa27d7f5cbb7 100644 --- a/arch/arm/mach-omap2/usb-host.c +++ b/arch/arm/mach-omap2/usb-host.c @@ -22,8 +22,12 @@ #include #include #include - -#include +#include +#include +#include +#include +#include +#include #include "soc.h" #include "omap_device.h" @@ -526,3 +530,155 @@ void __init usbhs_init(struct usbhs_omap_platform_data *pdata) } #endif + +/* Template for PHY regulators */ +static struct fixed_voltage_config hsusb_reg_config = { + /* .supply_name filled later */ + .microvolts = 3300000, + .gpio = -1, /* updated later */ + .startup_delay = 70000, /* 70msec */ + .enable_high = 1, /* updated later */ + .enabled_at_boot = 0, /* keep in RESET */ + /* .init_data filled later */ +}; + +static const char *nop_name = "nop_usb_xceiv"; /* NOP PHY driver */ +static const char *reg_name = "reg-fixed-voltage"; /* Regulator driver */ + +/** + * usbhs_add_regulator - Add a gpio based fixed voltage regulator device + * @name: name for the regulator + * @dev_id: device id of the device this regulator supplies power to + * @dev_supply: supply name that the device expects + * @gpio: GPIO number + * @polarity: 1 - Active high, 0 - Active low + */ +static int usbhs_add_regulator(char *name, char *dev_id, char *dev_supply, + int gpio, int polarity) +{ + struct regulator_consumer_supply *supplies; + struct regulator_init_data *reg_data; + struct fixed_voltage_config *config; + struct platform_device *pdev; + int ret; + + supplies = kzalloc(sizeof(*supplies), GFP_KERNEL); + if (!supplies) + return -ENOMEM; + + supplies->supply = dev_supply; + supplies->dev_name = dev_id; + + reg_data = kzalloc(sizeof(*reg_data), GFP_KERNEL); + if (!reg_data) + return -ENOMEM; + + reg_data->constraints.valid_ops_mask = REGULATOR_CHANGE_STATUS; + reg_data->consumer_supplies = supplies; + reg_data->num_consumer_supplies = 1; + + config = kmemdup(&hsusb_reg_config, sizeof(hsusb_reg_config), + GFP_KERNEL); + if (!config) + return -ENOMEM; + + config->supply_name = name; + config->gpio = gpio; + config->enable_high = polarity; + config->init_data = reg_data; + + /* create a regulator device */ + pdev = kzalloc(sizeof(*pdev), GFP_KERNEL); + if (!pdev) + return -ENOMEM; + + pdev->id = PLATFORM_DEVID_AUTO; + pdev->name = reg_name; + pdev->dev.platform_data = config; + + ret = platform_device_register(pdev); + if (ret) + pr_err("%s: Failed registering regulator %s for %s\n", + __func__, name, dev_id); + + return ret; +} + +int usbhs_init_phys(struct usbhs_phy_data *phy, int num_phys) +{ + char *rail_name; + int i, len; + struct platform_device *pdev; + char *phy_id; + + /* the phy_id will be something like "nop_usb_xceiv.1" */ + len = strlen(nop_name) + 3; /* 3 -> ".1" and NULL terminator */ + + for (i = 0; i < num_phys; i++) { + + if (!phy->port) { + pr_err("%s: Invalid port 0. Must start from 1\n", + __func__); + continue; + } + + /* do we need a NOP PHY device ? */ + if (!gpio_is_valid(phy->reset_gpio) && + !gpio_is_valid(phy->vcc_gpio)) + continue; + + /* create a NOP PHY device */ + pdev = kzalloc(sizeof(*pdev), GFP_KERNEL); + if (!pdev) + return -ENOMEM; + + pdev->id = phy->port; + pdev->name = nop_name; + pdev->dev.platform_data = phy->platform_data; + + phy_id = kmalloc(len, GFP_KERNEL); + if (!phy_id) + return -ENOMEM; + + scnprintf(phy_id, len, "nop_usb_xceiv.%d\n", + pdev->id); + + if (platform_device_register(pdev)) { + pr_err("%s: Failed to register device %s\n", + __func__, phy_id); + continue; + } + + usb_bind_phy("ehci-omap.0", phy->port - 1, phy_id); + + /* Do we need RESET regulator ? */ + if (gpio_is_valid(phy->reset_gpio)) { + + rail_name = kmalloc(13, GFP_KERNEL); + if (!rail_name) + return -ENOMEM; + + scnprintf(rail_name, 13, "hsusb%d_reset", phy->port); + + usbhs_add_regulator(rail_name, phy_id, "reset", + phy->reset_gpio, 1); + } + + /* Do we need VCC regulator ? */ + if (gpio_is_valid(phy->vcc_gpio)) { + + rail_name = kmalloc(13, GFP_KERNEL); + if (!rail_name) + return -ENOMEM; + + scnprintf(rail_name, 13, "hsusb%d_vcc", phy->port); + + usbhs_add_regulator(rail_name, phy_id, "vcc", + phy->vcc_gpio, phy->vcc_polarity); + } + + phy++; + } + + return 0; +} diff --git a/arch/arm/mach-omap2/usb.h b/arch/arm/mach-omap2/usb.h index 3319f5cf47a3..e7261ebcf7b0 100644 --- a/arch/arm/mach-omap2/usb.h +++ b/arch/arm/mach-omap2/usb.h @@ -53,8 +53,17 @@ #define USBPHY_OTGSESSEND_EN (1 << 20) #define USBPHY_DATA_POLARITY (1 << 23) +struct usbhs_phy_data { + int port; /* 1 indexed port number */ + int reset_gpio; + int vcc_gpio; + bool vcc_polarity; /* 1 active high, 0 active low */ + void *platform_data; +}; + extern void usb_musb_init(struct omap_musb_board_data *board_data); extern void usbhs_init(struct usbhs_omap_platform_data *pdata); +extern int usbhs_init_phys(struct usbhs_phy_data *phy, int num_phys); extern void am35x_musb_reset(void); extern void am35x_musb_phy_power(u8 on); -- cgit v1.2.3 From 84337b633327bff82a240f6c6658488059b00149 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 20 Mar 2013 17:44:42 +0200 Subject: ARM: OMAP2+: omap4panda: Adapt to ehci-omap changes Use usbhs_init_phys() to register the PHY's VCC and RESET regulators and the NOP PHY device. Get rid of managing the PHY clock as it will be done by the PHY driver. For that to work we create a clock alias that links the PHY clock name to the PHY device name. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-omap4panda.c | 55 +++++++++++++--------------------- 1 file changed, 21 insertions(+), 34 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c index b02c2f00609b..a71ad345f20d 100644 --- a/arch/arm/mach-omap2/board-omap4panda.c +++ b/arch/arm/mach-omap2/board-omap4panda.c @@ -31,6 +31,7 @@ #include #include #include +#include #include #include #include @@ -132,6 +133,22 @@ static struct platform_device btwilink_device = { .id = -1, }; +/* PHY device on HS USB Port 1 i.e. nop_usb_xceiv.1 */ +static struct nop_usb_xceiv_platform_data hsusb1_phy_data = { + /* FREF_CLK3 provides the 19.2 MHz reference clock to the PHY */ + .clk_rate = 19200000, +}; + +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 1, + .reset_gpio = GPIO_HUB_NRESET, + .vcc_gpio = GPIO_HUB_POWER, + .vcc_polarity = 1, + .platform_data = &hsusb1_phy_data, + }, +}; + static struct platform_device *panda_devices[] __initdata = { &leds_gpio, &wl1271_device, @@ -142,49 +159,19 @@ static struct platform_device *panda_devices[] __initdata = { static struct usbhs_omap_platform_data usbhs_bdata __initdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - .phy_reset = false, - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = -EINVAL, - .reset_gpio_port[2] = -EINVAL -}; - -static struct gpio panda_ehci_gpios[] __initdata = { - { GPIO_HUB_POWER, GPIOF_OUT_INIT_LOW, "hub_power" }, - { GPIO_HUB_NRESET, GPIOF_OUT_INIT_LOW, "hub_nreset" }, }; static void __init omap4_ehci_init(void) { int ret; - struct clk *phy_ref_clk; /* FREF_CLK3 provides the 19.2 MHz reference clock to the PHY */ - phy_ref_clk = clk_get(NULL, "auxclk3_ck"); - if (IS_ERR(phy_ref_clk)) { - pr_err("Cannot request auxclk3\n"); - return; - } - clk_set_rate(phy_ref_clk, 19200000); - clk_prepare_enable(phy_ref_clk); - - /* disable the power to the usb hub prior to init and reset phy+hub */ - ret = gpio_request_array(panda_ehci_gpios, - ARRAY_SIZE(panda_ehci_gpios)); - if (ret) { - pr_err("Unable to initialize EHCI power/reset\n"); - return; - } - - gpio_export(GPIO_HUB_POWER, 0); - gpio_export(GPIO_HUB_NRESET, 0); - gpio_set_value(GPIO_HUB_NRESET, 1); + ret = clk_add_alias("main_clk", "nop_usb_xceiv.1", "auxclk3_ck", NULL); + if (ret) + pr_err("Failed to add main_clk alias to auxclk3_ck\n"); + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); - - /* enable power to hub */ - gpio_set_value(GPIO_HUB_POWER, 1); } static struct omap_musb_board_data musb_board_data = { -- cgit v1.2.3 From 60226717fe62cfc9ebe29ef0a6cd64bc1e0c49af Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 20 Mar 2013 17:44:43 +0200 Subject: ARM: OMAP3: Beagle: Adapt to ehci-omap changes Use usbhs_init_phys() to register the PHY's VCC and RESET regulators and the NOP PHY device. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-omap3beagle.c | 32 ++++++++++++++++++++++---------- 1 file changed, 22 insertions(+), 10 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index c3558f93d42c..5382215a49bc 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -33,6 +33,7 @@ #include #include #include +#include #include #include @@ -277,6 +278,21 @@ static struct regulator_consumer_supply beagle_vsim_supply[] = { static struct gpio_led gpio_leds[]; +/* PHY's VCC regulator might be added later, so flag that we need it */ +static struct nop_usb_xceiv_platform_data hsusb2_phy_data = { + .needs_vcc = true, +}; + +static struct usbhs_phy_data phy_data[] = { + { + .port = 2, + .reset_gpio = 147, + .vcc_gpio = -1, /* updated in beagle_twl_gpio_setup */ + .vcc_polarity = 1, /* updated in beagle_twl_gpio_setup */ + .platform_data = &hsusb2_phy_data, + }, +}; + static int beagle_twl_gpio_setup(struct device *dev, unsigned gpio, unsigned ngpio) { @@ -318,9 +334,11 @@ static int beagle_twl_gpio_setup(struct device *dev, } dvi_panel.power_down_gpio = beagle_config.dvi_pd_gpio; - gpio_request_one(gpio + TWL4030_GPIO_MAX, beagle_config.usb_pwr_level, - "nEN_USB_PWR"); + /* TWL4030_GPIO_MAX i.e. LED_GPO controls HS USB Port 2 power */ + phy_data[0].vcc_gpio = gpio + TWL4030_GPIO_MAX; + phy_data[0].vcc_polarity = beagle_config.usb_pwr_level; + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); return 0; } @@ -453,15 +471,7 @@ static struct platform_device *omap3_beagle_devices[] __initdata = { }; static struct usbhs_omap_platform_data usbhs_bdata __initdata = { - - .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = 147, - .reset_gpio_port[2] = -EINVAL }; #ifdef CONFIG_OMAP_MUX @@ -543,7 +553,9 @@ static void __init omap3_beagle_init(void) usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); usb_musb_init(NULL); + usbhs_init(&usbhs_bdata); + board_nand_init(omap3beagle_nand_partitions, ARRAY_SIZE(omap3beagle_nand_partitions), NAND_CS, NAND_BUSWIDTH_16, NULL); -- cgit v1.2.3 From 0047c909fbde59b6c90cb925bbfe1098d3796c2e Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 20 Mar 2013 17:44:44 +0200 Subject: ARM: OMAP3: 3430SDP: Adapt to ehci-omap changes Use usbhs_init_phys() to register the PHY's RESET regulators and the NOP PHY devices. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-3430sdp.c | 21 +++++++++++++++------ 1 file changed, 15 insertions(+), 6 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c index ce812decfaca..7eb9651dd0f7 100644 --- a/arch/arm/mach-omap2/board-3430sdp.c +++ b/arch/arm/mach-omap2/board-3430sdp.c @@ -445,16 +445,23 @@ static void enable_board_wakeup_source(void) OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP); } +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 1, + .reset_gpio = 57, + .vcc_gpio = -EINVAL, + }, + { + .port = 2, + .reset_gpio = 61, + .vcc_gpio = -EINVAL, + }, +}; + static struct usbhs_omap_platform_data usbhs_bdata __initdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = 57, - .reset_gpio_port[1] = 61, - .reset_gpio_port[2] = -EINVAL }; #ifdef CONFIG_OMAP_MUX @@ -606,6 +613,8 @@ static void __init omap_3430sdp_init(void) board_flash_init(sdp_flash_partitions, chip_sel_3430, 0); sdp3430_display_init(); enable_board_wakeup_source(); + + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); } -- cgit v1.2.3 From 63e135a75ff41cc9ee1ac4012c505d46544dc10e Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 20 Mar 2013 17:44:45 +0200 Subject: ARM: OMAP3: 3630SDP: Adapt to ehci-omap changes Use usbhs_init_phys() to register the PHY's RESET regulators and the NOP PHY devices. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-3630sdp.c | 21 +++++++++++++++------ 1 file changed, 15 insertions(+), 6 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-3630sdp.c b/arch/arm/mach-omap2/board-3630sdp.c index 67447bd4564f..20d6d8189240 100644 --- a/arch/arm/mach-omap2/board-3630sdp.c +++ b/arch/arm/mach-omap2/board-3630sdp.c @@ -53,16 +53,23 @@ static void enable_board_wakeup_source(void) OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP); } +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 1, + .reset_gpio = 126, + .vcc_gpio = -EINVAL, + }, + { + .port = 2, + .reset_gpio = 61, + .vcc_gpio = -EINVAL, + }, +}; + static struct usbhs_omap_platform_data usbhs_bdata __initdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = 126, - .reset_gpio_port[1] = 61, - .reset_gpio_port[2] = -EINVAL }; #ifdef CONFIG_OMAP_MUX @@ -199,6 +206,8 @@ static void __init omap_sdp_init(void) board_smc91x_init(); board_flash_init(sdp_flash_partitions, chip_sel_sdp, NAND_BUSWIDTH_16); enable_board_wakeup_source(); + + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); } -- cgit v1.2.3 From 4a2ee5da83fb26cd74edbfb1b67700caef148adb Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 20 Mar 2013 17:44:46 +0200 Subject: ARM: OMAP: AM3517crane: Adapt to ehci-omap changes Use usbhs_init_phys() to register the PHY's VCC and RESET regulators and the NOP PHY device. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-am3517crane.c | 24 ++++++++++-------------- 1 file changed, 10 insertions(+), 14 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-am3517crane.c b/arch/arm/mach-omap2/board-am3517crane.c index 7d3358b2e593..fc53911d0d13 100644 --- a/arch/arm/mach-omap2/board-am3517crane.c +++ b/arch/arm/mach-omap2/board-am3517crane.c @@ -47,15 +47,17 @@ static struct omap_board_mux board_mux[] __initdata = { }; #endif +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 1, + .reset_gpio = GPIO_USB_NRESET, + .vcc_gpio = GPIO_USB_POWER, + .vcc_polarity = 1, + }, +}; + static struct usbhs_omap_platform_data usbhs_bdata __initdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = GPIO_USB_NRESET, - .reset_gpio_port[1] = -EINVAL, - .reset_gpio_port[2] = -EINVAL }; static struct mtd_partition crane_nand_partitions[] = { @@ -131,13 +133,7 @@ static void __init am3517_crane_init(void) return; } - ret = gpio_request_one(GPIO_USB_POWER, GPIOF_OUT_INIT_HIGH, - "usb_ehci_enable"); - if (ret < 0) { - pr_err("Can not request GPIO %d\n", GPIO_USB_POWER); - return; - } - + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); am35xx_emac_init(AM35XX_DEFAULT_MDIO_FREQUENCY, 1); } -- cgit v1.2.3 From 9413624c25c9cde60482a6b7e343f49b8d6eb0dc Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 20 Mar 2013 17:44:47 +0200 Subject: ARM: OMAP: AM3517evm: Adapt to ehci-omap changes Use usbhs_init_phys() to register the PHY's RESET regulators and the NOP PHY device. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-am3517evm.c | 17 ++++++++++------- 1 file changed, 10 insertions(+), 7 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-am3517evm.c b/arch/arm/mach-omap2/board-am3517evm.c index 9fb85908a61e..191f9762ba63 100644 --- a/arch/arm/mach-omap2/board-am3517evm.c +++ b/arch/arm/mach-omap2/board-am3517evm.c @@ -274,6 +274,14 @@ static __init void am3517_evm_mcbsp1_init(void) omap_ctrl_writel(devconf0, OMAP2_CONTROL_DEVCONF0); } +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 1, + .reset_gpio = 57, + .vcc_gpio = -EINVAL, + }, +}; + static struct usbhs_omap_platform_data usbhs_bdata __initdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, #if defined(CONFIG_PANEL_SHARP_LQ043T1DG01) || \ @@ -282,12 +290,6 @@ static struct usbhs_omap_platform_data usbhs_bdata __initdata = { #else .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, #endif - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = 57, - .reset_gpio_port[1] = -EINVAL, - .reset_gpio_port[2] = -EINVAL }; #ifdef CONFIG_OMAP_MUX @@ -349,7 +351,6 @@ static struct omap2_hsmmc_info mmc[] = { {} /* Terminator */ }; - static void __init am3517_evm_init(void) { omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); @@ -361,6 +362,8 @@ static void __init am3517_evm_init(void) /* Configure GPIO for EHCI port */ omap_mux_init_gpio(57, OMAP_PIN_OUTPUT); + + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); am3517_evm_hecc_init(&am3517_evm_hecc_pdata); /* DSS */ -- cgit v1.2.3 From 59b1499a702f3fb0e0571580a97a5d72023b8f53 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 20 Mar 2013 17:44:48 +0200 Subject: ARM: OMAP3: cm-t35: Adapt to ehci-omap changes Use usbhs_init_phys() to register the PHY's RESET regulators and the NOP PHY devices. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-cm-t35.c | 20 ++++++++++++++------ 1 file changed, 14 insertions(+), 6 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c index af2bb219e214..7fda3f5f8a7f 100644 --- a/arch/arm/mach-omap2/board-cm-t35.c +++ b/arch/arm/mach-omap2/board-cm-t35.c @@ -419,15 +419,22 @@ static struct omap2_hsmmc_info mmc[] = { {} /* Terminator */ }; +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 1, + .reset_gpio = OMAP_MAX_GPIO_LINES + 6, + .vcc_gpio = -EINVAL, + }, + { + .port = 2, + .reset_gpio = OMAP_MAX_GPIO_LINES + 7, + .vcc_gpio = -EINVAL, + }, +}; + static struct usbhs_omap_platform_data usbhs_bdata __initdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = OMAP_MAX_GPIO_LINES + 6, - .reset_gpio_port[1] = OMAP_MAX_GPIO_LINES + 7, - .reset_gpio_port[2] = -EINVAL }; static void __init cm_t35_init_usbh(void) @@ -444,6 +451,7 @@ static void __init cm_t35_init_usbh(void) msleep(1); } + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); } -- cgit v1.2.3 From a0409c9ae17827b9e5a7ad5e4bc85eb437efab07 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 20 Mar 2013 17:44:49 +0200 Subject: ARM: OMAP3: cm-t3517: Adapt to ehci-omap changes Use usbhs_init_phys() to register the PHY's RESET regulators and the NOP PHY devices. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-cm-t3517.c | 20 ++++++++++++++------ 1 file changed, 14 insertions(+), 6 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-cm-t3517.c b/arch/arm/mach-omap2/board-cm-t3517.c index a66da808cc4a..6920f6cfc97c 100644 --- a/arch/arm/mach-omap2/board-cm-t3517.c +++ b/arch/arm/mach-omap2/board-cm-t3517.c @@ -188,15 +188,22 @@ static inline void cm_t3517_init_rtc(void) {} #define HSUSB2_RESET_GPIO (147) #define USB_HUB_RESET_GPIO (152) +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 1, + .reset_gpio = HSUSB1_RESET_GPIO, + .vcc_gpio = -EINVAL, + }, + { + .port = 2, + .reset_gpio = HSUSB2_RESET_GPIO, + .vcc_gpio = -EINVAL, + }, +}; + static struct usbhs_omap_platform_data cm_t3517_ehci_pdata __initdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = HSUSB1_RESET_GPIO, - .reset_gpio_port[1] = HSUSB2_RESET_GPIO, - .reset_gpio_port[2] = -EINVAL, }; static int __init cm_t3517_init_usbh(void) @@ -213,6 +220,7 @@ static int __init cm_t3517_init_usbh(void) msleep(1); } + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&cm_t3517_ehci_pdata); return 0; -- cgit v1.2.3 From e3d38f9b07efba8a9c6412138f9309d21a87d39d Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 20 Mar 2013 17:44:50 +0200 Subject: ARM: OMAP: devkit8000: Adapt to ehci-omap changes Remove deprecated USBHS platform data. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-devkit8000.c | 8 -------- 1 file changed, 8 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c index 53056c3b0836..42fbf1ef12a9 100644 --- a/arch/arm/mach-omap2/board-devkit8000.c +++ b/arch/arm/mach-omap2/board-devkit8000.c @@ -437,15 +437,7 @@ static struct platform_device *devkit8000_devices[] __initdata = { }; static struct usbhs_omap_platform_data usbhs_bdata __initdata = { - .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = -EINVAL, - .reset_gpio_port[2] = -EINVAL }; #ifdef CONFIG_OMAP_MUX -- cgit v1.2.3 From 9c4d678e7452af7b07c7e2ba4c7712bf4aa004a4 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 20 Mar 2013 17:44:51 +0200 Subject: ARM: OMAP3: igep0020: Adapt to ehci-omap changes Use usbhs_init_phys() to register the PHY's RESET regulators and the NOP PHY devices. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-igep0020.c | 32 ++++++++++++++++++-------------- 1 file changed, 18 insertions(+), 14 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c index bf92678a01d0..95ccec0eeab9 100644 --- a/arch/arm/mach-omap2/board-igep0020.c +++ b/arch/arm/mach-omap2/board-igep0020.c @@ -527,26 +527,28 @@ static void __init igep_i2c_init(void) omap3_pmic_init("twl4030", &igep_twldata); } +static struct usbhs_phy_data igep2_phy_data[] __initdata = { + { + .port = 1, + .reset_gpio = IGEP2_GPIO_USBH_NRESET, + .vcc_gpio = -EINVAL, + }, +}; + +static struct usbhs_phy_data igep3_phy_data[] __initdata = { + { + .port = 2, + .reset_gpio = IGEP3_GPIO_USBH_NRESET, + .vcc_gpio = -EINVAL, + }, +}; + static struct usbhs_omap_platform_data igep2_usbhs_bdata __initdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = IGEP2_GPIO_USBH_NRESET, - .reset_gpio_port[1] = -EINVAL, - .reset_gpio_port[2] = -EINVAL, }; static struct usbhs_omap_platform_data igep3_usbhs_bdata __initdata = { - .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = IGEP3_GPIO_USBH_NRESET, - .reset_gpio_port[2] = -EINVAL, }; #ifdef CONFIG_OMAP_MUX @@ -642,8 +644,10 @@ static void __init igep_init(void) if (machine_is_igep0020()) { omap_display_init(&igep2_dss_data); igep2_init_smsc911x(); + usbhs_init_phys(igep2_phy_data, ARRAY_SIZE(igep2_phy_data)); usbhs_init(&igep2_usbhs_bdata); } else { + usbhs_init_phys(igep3_phy_data, ARRAY_SIZE(igep3_phy_data)); usbhs_init(&igep3_usbhs_bdata); } } -- cgit v1.2.3 From 6ef818ee3544ec344cb289a81693d10ad480d2e0 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 20 Mar 2013 17:44:52 +0200 Subject: ARM: OMAP3: omap3evm: Adapt to ehci-omap changes Use usbhs_init_phys() to register the PHY's RESET regulator and the NOP PHY device. VAUX2 supplies the PHY's VCC. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-omap3evm.c | 25 +++++++++++++------------ 1 file changed, 13 insertions(+), 12 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c index 48789e0bb915..2de92facc8a3 100644 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ b/arch/arm/mach-omap2/board-omap3evm.c @@ -496,7 +496,7 @@ struct wl12xx_platform_data omap3evm_wlan_data __initdata = { static struct regulator_consumer_supply omap3evm_vaux2_supplies[] = { REGULATOR_SUPPLY("VDD_CSIPHY1", "omap3isp"), /* OMAP ISP */ REGULATOR_SUPPLY("VDD_CSIPHY2", "omap3isp"), /* OMAP ISP */ - REGULATOR_SUPPLY("hsusb1", "ehci-omap.0"), + REGULATOR_SUPPLY("vcc", "nop_usb_xceiv.2"), /* hsusb port 2 */ REGULATOR_SUPPLY("vaux2", NULL), }; @@ -539,17 +539,16 @@ static int __init omap3_evm_i2c_init(void) return 0; } -static struct usbhs_omap_platform_data usbhs_bdata __initdata = { +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 2, + .reset_gpio = -1, /* set at runtime */ + .vcc_gpio = -EINVAL, + }, +}; - .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, +static struct usbhs_omap_platform_data usbhs_bdata __initdata = { .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - /* PHY reset GPIO will be runtime programmed based on EVM version */ - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = -EINVAL, - .reset_gpio_port[2] = -EINVAL }; #ifdef CONFIG_OMAP_MUX @@ -725,7 +724,7 @@ static void __init omap3_evm_init(void) /* setup EHCI phy reset config */ omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP); - usbhs_bdata.reset_gpio_port[1] = 21; + phy_data[0].reset_gpio = 21; /* EVM REV >= E can supply 500mA with EXTVBUS programming */ musb_board_data.power = 500; @@ -733,10 +732,12 @@ static void __init omap3_evm_init(void) } else { /* setup EHCI phy reset on MDC */ omap_mux_init_gpio(135, OMAP_PIN_OUTPUT); - usbhs_bdata.reset_gpio_port[1] = 135; + phy_data[0].reset_gpio = 135; } usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); usb_musb_init(&musb_board_data); + + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); board_nand_init(omap3evm_nand_partitions, ARRAY_SIZE(omap3evm_nand_partitions), NAND_CS, -- cgit v1.2.3 From 08a15fe857103f12639842c89d3fd5ae07600125 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 20 Mar 2013 17:44:53 +0200 Subject: ARM: OMAP3: omap3pandora: Adapt to ehci-omap changes Use usbhs_init_phys() to register the PHY's RESET regulator and NOP PHY device. VAUX2 supplies the PHY's VCC. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-omap3pandora.c | 21 ++++++++++++--------- 1 file changed, 12 insertions(+), 9 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c index 2bba362148a0..1004d2aaa68f 100644 --- a/arch/arm/mach-omap2/board-omap3pandora.c +++ b/arch/arm/mach-omap2/board-omap3pandora.c @@ -346,7 +346,7 @@ static struct regulator_consumer_supply pandora_vcc_lcd_supply[] = { }; static struct regulator_consumer_supply pandora_usb_phy_supply[] = { - REGULATOR_SUPPLY("hsusb1", "ehci-omap.0"), + REGULATOR_SUPPLY("vcc", "nop_usb_xceiv.2"), /* hsusb port 2 */ }; /* ads7846 on SPI and 2 nub controllers on I2C */ @@ -561,6 +561,14 @@ fail: printk(KERN_ERR "wl1251 board initialisation failed\n"); } +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 2, + .reset_gpio = 16, + .vcc_gpio = -EINVAL, + }, +}; + static struct platform_device *omap3pandora_devices[] __initdata = { &pandora_leds_gpio, &pandora_keys_gpio, @@ -569,15 +577,7 @@ static struct platform_device *omap3pandora_devices[] __initdata = { }; static struct usbhs_omap_platform_data usbhs_bdata __initdata = { - - .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = 16, - .reset_gpio_port[2] = -EINVAL }; #ifdef CONFIG_OMAP_MUX @@ -601,7 +601,10 @@ static void __init omap3pandora_init(void) spi_register_board_info(omap3pandora_spi_board_info, ARRAY_SIZE(omap3pandora_spi_board_info)); omap_ads7846_init(1, OMAP3_PANDORA_TS_GPIO, 0, NULL); + + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); + usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); usb_musb_init(NULL); gpmc_nand_init(&pandora_nand_data, NULL); -- cgit v1.2.3 From af29470bdb084542ed9d38c052f9ff24f27b3ae9 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 20 Mar 2013 17:44:54 +0200 Subject: ARM: OMAP3: omap3stalker: Adapt to ehci-omap changes Use usbhs_init_phys() to register the PHY's RESET regulator and the NOP PHY device. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-omap3stalker.c | 17 ++++++++++------- 1 file changed, 10 insertions(+), 7 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-omap3stalker.c b/arch/arm/mach-omap2/board-omap3stalker.c index 95c10b3aa678..bf0956489899 100644 --- a/arch/arm/mach-omap2/board-omap3stalker.c +++ b/arch/arm/mach-omap2/board-omap3stalker.c @@ -358,19 +358,20 @@ static int __init omap3_stalker_i2c_init(void) #define OMAP3_STALKER_TS_GPIO 175 +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 2, + .reset_gpio = 21, + .vcc_gpio = -EINVAL, + }, +}; + static struct platform_device *omap3_stalker_devices[] __initdata = { &keys_gpio, }; static struct usbhs_omap_platform_data usbhs_bdata __initdata = { - .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = 21, - .reset_gpio_port[2] = -EINVAL, }; #ifdef CONFIG_OMAP_MUX @@ -407,6 +408,8 @@ static void __init omap3_stalker_init(void) omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL); usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); usb_musb_init(NULL); + + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); omap_ads7846_init(1, OMAP3_STALKER_TS_GPIO, 310, NULL); -- cgit v1.2.3 From 3da6ca3596aef2a8536b3449c0f05e77552b0b63 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 20 Mar 2013 17:44:55 +0200 Subject: ARM: OMAP3: omap3touchbook: Adapt to ehci-omap changes Use usbhs_init_phys() to register the PHY's RESET regulator and the NOP PHY device. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-omap3touchbook.c | 17 ++++++++++------- 1 file changed, 10 insertions(+), 7 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-omap3touchbook.c b/arch/arm/mach-omap2/board-omap3touchbook.c index bcd44fbcd877..7da48bc42bbf 100644 --- a/arch/arm/mach-omap2/board-omap3touchbook.c +++ b/arch/arm/mach-omap2/board-omap3touchbook.c @@ -305,21 +305,22 @@ static struct omap_board_mux board_mux[] __initdata = { }; #endif +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 2, + .reset_gpio = 147, + .vcc_gpio = -EINVAL, + }, +}; + static struct platform_device *omap3_touchbook_devices[] __initdata = { &leds_gpio, &keys_gpio, }; static struct usbhs_omap_platform_data usbhs_bdata __initdata = { - .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = 147, - .reset_gpio_port[2] = -EINVAL }; static void omap3_touchbook_poweroff(void) @@ -368,6 +369,8 @@ static void __init omap3_touchbook_init(void) omap_ads7846_init(4, OMAP3_TS_GPIO, 310, &ads7846_pdata); usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); usb_musb_init(NULL); + + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); board_nand_init(omap3touchbook_nand_partitions, ARRAY_SIZE(omap3touchbook_nand_partitions), NAND_CS, -- cgit v1.2.3 From 14c67d2309a77dff234da7992e9db508bd2f5e8e Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 20 Mar 2013 17:44:56 +0200 Subject: ARM: OMAP3: overo: Adapt to ehci-omap changes Use usbhs_init_phys() to register the PHY's RESET regulator and the NOP PHY device. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-overo.c | 16 ++++++++++------ 1 file changed, 10 insertions(+), 6 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index 86bab51154ee..ab79a4422bcc 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -458,14 +458,16 @@ static int __init overo_spi_init(void) return 0; } +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 2, + .reset_gpio = OVERO_GPIO_USBH_NRESET, + .vcc_gpio = -EINVAL, + }, +}; + static struct usbhs_omap_platform_data usbhs_bdata __initdata = { - .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - .phy_reset = true, - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = OVERO_GPIO_USBH_NRESET, - .reset_gpio_port[2] = -EINVAL }; #ifdef CONFIG_OMAP_MUX @@ -502,6 +504,8 @@ static void __init overo_init(void) ARRAY_SIZE(overo_nand_partitions), NAND_CS, 0, NULL); usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); usb_musb_init(NULL); + + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); overo_spi_init(); overo_init_smsc911x(); -- cgit v1.2.3 From 9b9208675dd04526917454eb000528309eacd2a5 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 20 Mar 2013 17:44:57 +0200 Subject: ARM: OMAP: zoom: Adapt to ehci-omap changes Use usbhs_init_phys() to register the PHY's RESET regulator and the NOP PHY device. Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-zoom.c | 16 ++++++++++------ 1 file changed, 10 insertions(+), 6 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-zoom.c b/arch/arm/mach-omap2/board-zoom.c index 5e4d4c9fe61a..1a3dd865d8eb 100644 --- a/arch/arm/mach-omap2/board-zoom.c +++ b/arch/arm/mach-omap2/board-zoom.c @@ -92,14 +92,16 @@ static struct mtd_partition zoom_nand_partitions[] = { }, }; +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 2, + .reset_gpio = ZOOM3_EHCI_RESET_GPIO, + .vcc_gpio = -EINVAL, + }, +}; + static struct usbhs_omap_platform_data usbhs_bdata __initdata = { - .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - .phy_reset = true, - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = ZOOM3_EHCI_RESET_GPIO, - .reset_gpio_port[2] = -EINVAL, }; static void __init omap_zoom_init(void) @@ -109,6 +111,8 @@ static void __init omap_zoom_init(void) } else if (machine_is_omap_zoom3()) { omap3_mux_init(board_mux, OMAP_PACKAGE_CBP); omap_mux_init_gpio(ZOOM3_EHCI_RESET_GPIO, OMAP_PIN_OUTPUT); + + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); } -- cgit v1.2.3 From f17c89948dcd60ecd5640fb8c7b30253faa00448 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 20 Mar 2013 17:44:58 +0200 Subject: ARM: dts: OMAP4: Add HS USB Host IP nodes MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Adds device nodes for HS USB Host module, TLL module, OHCI and EHCI controllers. CC: Benoît Cousson Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap4.dtsi | 30 ++++++++++++++++++++++++++++++ 1 file changed, 30 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index 739bb79e410e..b7db1a2b6ca7 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -529,5 +529,35 @@ ti,hwmods = "timer11"; ti,timer-pwm; }; + + usbhstll: usbhstll@4a062000 { + compatible = "ti,usbhs-tll"; + reg = <0x4a062000 0x1000>; + interrupts = <0 78 0x4>; + ti,hwmods = "usb_tll_hs"; + }; + + usbhshost: usbhshost@4a064000 { + compatible = "ti,usbhs-host"; + reg = <0x4a064000 0x800>; + ti,hwmods = "usb_host_hs"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + usbhsohci: ohci@4a064800 { + compatible = "ti,ohci-omap3", "usb-ohci"; + reg = <0x4a064800 0x400>; + interrupt-parent = <&gic>; + interrupts = <0 76 0x4>; + }; + + usbhsehci: ehci@4a064c00 { + compatible = "ti,ehci-omap", "usb-ehci"; + reg = <0x4a064c00 0x400>; + interrupt-parent = <&gic>; + interrupts = <0 77 0x4>; + }; + }; }; }; -- cgit v1.2.3 From af3eb366ae6a3f33eb6e7f8c282ab6859b2fca95 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 20 Mar 2013 17:44:59 +0200 Subject: ARM: dts: OMAP3: Add HS USB Host IP nodes MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Adds device nodes for HS USB Host module, TLL module, OHCI and EHCI controllers. CC: Benoît Cousson Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3.dtsi | 31 +++++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi index 1acc26148ffc..a14f74bbce7c 100644 --- a/arch/arm/boot/dts/omap3.dtsi +++ b/arch/arm/boot/dts/omap3.dtsi @@ -397,5 +397,36 @@ ti,timer-alwon; ti,timer-secure; }; + + usbhstll: usbhstll@48062000 { + compatible = "ti,usbhs-tll"; + reg = <0x48062000 0x1000>; + interrupts = <78>; + ti,hwmods = "usb_tll_hs"; + }; + + usbhshost: usbhshost@48064000 { + compatible = "ti,usbhs-host"; + reg = <0x48064000 0x400>; + ti,hwmods = "usb_host_hs"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + usbhsohci: ohci@48064400 { + compatible = "ti,ohci-omap3", "usb-ohci"; + reg = <0x48064400 0x400>; + interrupt-parent = <&intc>; + interrupts = <76>; + }; + + usbhsehci: ehci@48064800 { + compatible = "ti,ehci-omap", "usb-ehci"; + reg = <0x48064800 0x400>; + interrupt-parent = <&intc>; + interrupts = <77>; + }; + }; + }; }; -- cgit v1.2.3 From 2e5f78aeceb6f203b514ca03a48e3fd056025524 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 20 Mar 2013 17:45:00 +0200 Subject: ARM: dts: omap3-beagle: Add USB Host support MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Provide RESET and Power regulators for the USB PHY, the USB Host port mode and the PHY device. Also provide pin multiplexer information for USB host pins. CC: Benoît Cousson Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-beagle.dts | 71 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 71 insertions(+) (limited to 'arch/arm') diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts index f624dc85d441..02d23f15fd86 100644 --- a/arch/arm/boot/dts/omap3-beagle.dts +++ b/arch/arm/boot/dts/omap3-beagle.dts @@ -38,6 +38,57 @@ }; }; + /* HS USB Port 2 RESET */ + hsusb2_reset: hsusb2_reset_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb2_reset"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio5 19 0>; /* gpio_147 */ + startup-delay-us = <70000>; + enable-active-high; + }; + + /* HS USB Port 2 Power */ + hsusb2_power: hsusb2_power_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb2_vbus"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&twl_gpio 18 0>; /* GPIO LEDA */ + startup-delay-us = <70000>; + }; + + /* HS USB Host PHY on PORT 2 */ + hsusb2_phy: hsusb2_phy { + compatible = "usb-nop-xceiv"; + reset-supply = <&hsusb2_reset>; + vcc-supply = <&hsusb2_power>; + }; +}; + +&omap3_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = < + &hsusbb2_pins + >; + + hsusbb2_pins: pinmux_hsusbb2_pins { + pinctrl-single,pins = < + 0x5c0 0x3 /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_clk OUTPUT */ + 0x5c2 0x3 /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_stp OUTPUT */ + 0x5c4 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dir INPUT | PULLDOWN */ + 0x5c6 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_nxt INPUT | PULLDOWN */ + 0x5c8 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat0 INPUT | PULLDOWN */ + 0x5cA 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat1 INPUT | PULLDOWN */ + 0x1a4 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat2 INPUT | PULLDOWN */ + 0x1a6 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat3 INPUT | PULLDOWN */ + 0x1a8 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat4 INPUT | PULLDOWN */ + 0x1aa 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat5 INPUT | PULLDOWN */ + 0x1ac 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat6 INPUT | PULLDOWN */ + 0x1ae 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat7 INPUT | PULLDOWN */ + >; + }; }; &i2c1 { @@ -65,3 +116,23 @@ &mmc3 { status = "disabled"; }; + +&usbhshost { + port2-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <0 &hsusb2_phy>; +}; + +&twl_gpio { + ti,use-leds; + /* pullups: BIT(1) */ + ti,pullups = <0x000002>; + /* + * pulldowns: + * BIT(2), BIT(6), BIT(7), BIT(8), BIT(13) + * BIT(15), BIT(16), BIT(17) + */ + ti,pulldowns = <0x03a1c4>; +}; -- cgit v1.2.3